Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

F280049CPMS

Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)

F280049CPMS from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GPIO29 bidirectional General-purpose I/O 29 (default GPIO), multiplexed with SCIA_TX, EPWM7_B, EQEP1_B, SPIB_STE, LINA_RX and ERRORSTS.
2 GPIO28 bidirectional General-purpose I/O 28 (default GPIO), multiplexed with SCIA_RX, EPWM7_A, EQEP1_A, LINA_TX, SPIB_CLK and ERRORSTS.
3 XRSn bidirectional Device reset input and watchdog reset output (open-drain with internal pullup); a 2.2 kΩ to 10 kΩ resistor should be placed between XRSn and VDDIO, and any noise-filter capacitor should be 100 nF or less.
4 VDD power_in 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins.
5 VSS power_in Digital ground; all VSS pins must be connected to the board ground.
6 A6/PGA5_OF input ADC-A input 6 (also PGA-5 optional output filter, CMPSS-5 comparator input and AIO228); keep the ADC input below VDDA + 0.3 V.
7 B2/C6/PGA3_OF input ADC-B input 2 (also ADC-C input 6, PGA-3 optional output filter and CMPSS-3 input); keep the ADC input below VDDA + 0.3 V.
8 B3/VDAC input ADC-B input 3 and optional external reference for the on-chip DAC; a 100 pF capacitor to VSSA is always present, and at least one 1 µF capacitor is required if used as the DAC reference.
9 A2/B6/PGA1_OF input ADC-A input 2 (also ADC-B input 6, PGA-1 optional output filter and CMPSS-1 input); keep the ADC input below VDDA + 0.3 V.
10 PGA1_GND power_in PGA-1, PGA-3 and PGA-5 ground (Kelvin ground reference, ideally equal to VSSA).
11 C4/PGA5_IN input ADC-C input 4 (also PGA-5 input and CMPSS-5 input); keep the ADC input below VDDA + 0.3 V.
12 C0/PGA1_IN input ADC-C input 0 (also PGA-1 input and CMPSS-1 input); keep the ADC input below VDDA + 0.3 V.
13 C2/PGA3_IN input ADC-C input 2 (also PGA-3 input and CMPSS-3 input); keep the ADC input below VDDA + 0.3 V.
14 A1/DACB_OUT input ADC-A input 1 (also buffered DAC-B output and AIO232); keep the ADC input below VDDA + 0.3 V.
15 A0/B15/C15/DACA_OUT input ADC-A input 0 (also ADC-B input 15, ADC-C input 15, buffered DAC-A output and AIO231); keep the ADC input below VDDA + 0.3 V.
16 VREFHIA bidirectional ADC-A/B/C high reference; drive externally in external-reference mode, device-driven in internal-reference mode, place at least 2.2 µF between each VREFHIx and its VREFLOx pin, and do not load externally.
17 VREFLOA input ADC-A/B/C low reference voltage; unused VREFLOx pins are tied to VSSA.
18 C1/PGA2_IN input ADC-C input 1 (also PGA-2 input and CMPSS-2 input); keep the ADC input below VDDA + 0.3 V.
19 C3/PGA4_IN input ADC-C input 3 (also PGA-4 input and CMPSS-4 input); keep the ADC input below VDDA + 0.3 V.
20 PGA2_GND power_in PGA-2, PGA-4 and PGA-6 ground (Kelvin ground reference, ideally equal to VSSA).
21 VSSA power_in Analog ground.
22 VDDA power_in 3.3 V analog supply; place a minimum 2.2 µF decoupling capacitor connected to VSSA on each VDDA pin.
23 A4/B8/PGA2_OF input ADC-A input 4 (also ADC-B input 8, PGA-2 optional output filter and CMPSS-2 input); keep the ADC input below VDDA + 0.3 V.
24 B4/C8/PGA4_OF input ADC-B input 4 (also ADC-C input 8, PGA-4 optional output filter and CMPSS-4 input); keep the ADC input below VDDA + 0.3 V.
25 A10/B1/C10/PGA7_OF input ADC-A input 10 (also ADC-B input 1, ADC-C input 10 and PGA-7 optional output filter); keep the ADC input below VDDA + 0.3 V.
26 VSS power_in Digital ground; all VSS pins must be connected to the board ground.
27 VDD power_in 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins.
28 VDDIO power_in 3.3 V digital I/O supply; place a minimum 0.1 µF decoupling capacitor on each VDDIO pin.
29 GPIO13 bidirectional General-purpose I/O 13 (default GPIO), multiplexed with EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX, PMBUSA_ALERT and FSIRXA_CLK.
30 GPIO12 bidirectional General-purpose I/O 12 (default GPIO), multiplexed with EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX, PMBUSA_CTL and FSIRXA_D0.
31 GPIO11 bidirectional General-purpose I/O 11 (default GPIO), multiplexed with EPWM6_B, SCIB_RX, OUTPUTXBAR7, EQEP1_B, SPIA_STE and FSIRXA_D1.
32 GPIO33 bidirectional General-purpose I/O 33 (default GPIO), multiplexed with I2CA_SCL, SPIB_STE, OUTPUTXBAR4, LINA_RX, SD1_C3, FSIRXA_CLK and CANA_RX.
33 GPIO16 bidirectional General-purpose I/O 16 (default GPIO), multiplexed with SPIA_SIMO, CANB_TX, OUTPUTXBAR7, EPWM5_A, SCIA_TX, SD1_D1, EQEP1_STROBE, PMBUSA_SCL and XCLKOUT.
34 GPIO17 bidirectional General-purpose I/O 17 (default GPIO), multiplexed with SPIA_SOMI, CANB_RX, OUTPUTXBAR8, EPWM5_B, SCIA_RX, SD1_C1, EQEP1_INDEX and PMBUSA_SDA.
35 GPIO24 bidirectional General-purpose I/O 24 (default GPIO), multiplexed with OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SD1_D1, PMBUSA_SCL, SCIA_TX and ERRORSTS.
36 TCK input JTAG test clock input with internal pullup.
37 GPIO37/TDO output JTAG test data output (TDO, default function); the pin is tri-stated when there is no JTAG activity, so an internal or external pullup is required to avoid a floating GPIO input.
38 TMS bidirectional JTAG test mode select with internal pullup, clocked on TCK rising edge; a 2.2 kΩ external pullup to VDDIO is recommended on the board.
39 GPIO35/TDI input JTAG test data input (TDI, default function); enable the internal pullup or add an external pullup to avoid a floating input.
40 GPIO32 bidirectional General-purpose I/O 32 (default GPIO), multiplexed with I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3, FSIRXA_D0 and CANA_TX.
41 GPIO18_X2 bidirectional General-purpose I/O 18 also serving as the X2 crystal oscillator output; GPIO18 and its mux options are usable only when INTOSC clocks the system and X1 has an external pull-down (1 kΩ recommended).
42 X1 bidirectional Crystal oscillator or single-ended 3.3 V clock input; device initialization software must configure this pin before enabling the crystal oscillator.
43 VDDIO power_in 3.3 V digital I/O supply; place a minimum 0.1 µF decoupling capacitor on each VDDIO pin.
44 VDD power_in 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins.
45 VSS power_in Digital ground; all VSS pins must be connected to the board ground.
46 VREGENZ input Internal regulator enable with internal pulldown; tie to VSS to enable the internal VREG and to VDDIO to use an external VDD supply.
47 GPIO8 bidirectional General-purpose I/O 8 (default GPIO), multiplexed with EPWM5_A, CANB_TX, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL and FSITXA_D1.
48 GPIO4 bidirectional General-purpose I/O 4 (default GPIO), multiplexed with EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK.
49 GPIO3 bidirectional General-purpose I/O 3 (default GPIO), multiplexed with EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and FSIRXA_D0.
50 GPIO2 bidirectional General-purpose I/O 2 (default GPIO), multiplexed with EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX and FSIRXA_D1.
51 GPIO1 bidirectional General-purpose I/O 1 (default GPIO), multiplexed with EPWM1_B and I2CA_SCL.
52 GPIO0 bidirectional General-purpose I/O 0 (default GPIO), multiplexed with EPWM1_A and I2CA_SDA.
53 VDDIO_SW power_in 3.3 V supply for the internal DC/DC regulator; if the DC/DC is used a 20 µF bulk input capacitor is required, and this pin must be tied to VDDIO.
54 GPIO23_VSW bidirectional General-purpose I/O 23 (default DC/DC mode) that serves as the internal DC/DC switching output VSW when DCDCEN = 1; it has about 100 pF internal capacitance, so an alternate GPIO is recommended where fast switching response is needed.
55 VSS_SW power_in Internal DC/DC regulator ground; must be tied to VSS.
56 GPIO22_VFBSW bidirectional General-purpose I/O 22 (default DC/DC mode) that serves as the internal DC/DC feedback VFBSW when DCDCEN = 1; connect it to the node where L(VSW) meets the VDD rail, as close to the device as possible.
57 GPIO7 bidirectional General-purpose I/O 7 (default GPIO), multiplexed with EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK.
58 VSS power_in Digital ground; all VSS pins must be connected to the board ground.
59 VDD power_in 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins.
60 VDDIO power_in 3.3 V digital I/O supply; place a minimum 0.1 µF decoupling capacitor on each VDDIO pin.
61 GPIO5 bidirectional General-purpose I/O 5 (default GPIO), multiplexed with EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1.
62 GPIO9 bidirectional General-purpose I/O 9 (default GPIO), multiplexed with EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX, SPIA_CLK and FSITXA_D0.
63 GPIO10 bidirectional General-purpose I/O 10 (default GPIO), multiplexed with EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI, I2CA_SDA and FSITXA_CLK.
64 GPIO6 bidirectional General-purpose I/O 6 (default GPIO), multiplexed with EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package LQFP-64(10x10)
Category Embedded Processors & Controllers
Pins 64

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDDIO 以 VSS 为基准 (供电电压,绝对最大额定值) VDDIO -0.3 4.6 V 以 VSS 为基准 58
VDDA 以 VSSA 为基准 (供电电压,绝对最大额定值) VDDA -0.3 4.6 V 以 VSSA 为基准 58
VDD 以 VSS 为基准 (内核供电电压,绝对最大额定值) VDD -0.3 1.5 V 以 VSS 为基准 58
VDDIO 和 VDDIO_SW 引脚之间的电压差 -0.3 0.3 V 58
输入电压 VIN (3.3V) VIN -0.3 4.6 V 58
输出电压 VO -0.3 4.6 V 58
数字输入钳位电流(每引脚) IIK -20 20 mA VIN < VSS 或 VIN > VDDIO 58
模拟输入钳位电流(每引脚) IIKANALOG -20 20 mA VIN < VSSA 或 VIN > VDDA 58
所有输入的总计钳位电流 IIKTOTAL -20 20 mA VIN < VSS/VSSA 或 VIN > VDDIO/VDDA 58
数字输出电流(每引脚) IOUT -20 20 mA 58
自然通风温度 TA -40 125 °C 自然通风 58
工作结温 TJ -40 150 °C 58
贮存温度 Tstg -65 150 °C 58
器件电源电压 VDDIO 和 VDDA(启用内部 BOR) VDDIO, VDDA 3.3 3.63 V 启用内部 BOR 59
器件电源电压 VDDIO 和 VDDA(禁用内部 BOR) VDDIO, VDDA 2.8 3.3 3.63 V 禁用内部 BOR 59
器件电源电压 VDD VDD 1.14 1.2 1.32 V 59
VDDIO 电源斜坡时间 tVDDIO-RAMP 10 ms 从 1V 到 VBOR-VDDIO(MAX) 59
结温 TJ(S 版本) TJ -40 125 °C S 版本 59
VDD 运行期间的电流消耗(外部电源) IDD 61 90 mA 请参阅节 6.5.4 61
VDDIO 运行期间的电流消耗(外部电源) IDDIO 26 45 mA 61
VDDA 运行期间的电流消耗(外部电源) IDDA 12 30 mA 61
器件处于空闲模式时的 VDD 电流消耗 IDD 18 40 mA CPU 处于空闲模式;闪存被断电;XCLKOUT 被关闭 61
器件处于空闲模式时的 VDDIO 电流消耗 IDDIO 1.2 4 mA 61
器件处于空闲模式时的 VDDA 电流消耗 IDDA 0.9 1.2 mA 61
器件处于停机模式时的 VDD 电流消耗 IDD 0.9 20 mA CPU 处于停机模式;闪存被断电;XCLKOUT 被关闭 61
器件处于停机模式时的 VDDIO 电流消耗 IDDIO 0.8 4 mA 61
器件处于停机模式时的 VDDA 电流消耗 IDDA 0.2 0.5 mA 61
擦除/编程周期期间的 VDD 电流消耗 IDD 40 70 mA CPU 从闪存运行擦除/编程;禁用 VREG;SYSCLK 100MHz 61
擦除/编程周期期间的 VDDIO 电流消耗 IDDIO 33 75 mA 61
擦除/编程周期期间的 VDDA 电流消耗 IDDA 0.1 2.5 mA 61
VDDIO 运行期间的电流消耗(内部 VREG) IDDIO 86 113 mA 请参阅节 6.5.4 61
VDDA 运行期间的电流消耗(内部 VREG) IDDA 12 30 mA 61
低电平输出电压 (IOL=IOL 最大值) VOL 0.4 V IOL=IOL 最大值 67
低电平输出电压 (IOL=100µA) VOL 0.2 V IOL = 100µA 67
高电平输入电压 (3.3V) VIH 2 V 67
低电平输入电压 (3.3V) VIL 0.8 V 67
VDDIO 欠压复位电压 VBOR-VDDIO 2.81 3 V 67
内部稳压器输出 VVREG 1.14 1.2 1.32 V 80
斜降时的 VDDIO 欠压复位电压 VBOR-VDDIO-DN 2.81 3 V XRSn 释放之后 80
CL1、CL2 负载电容 CL1, CL2 12 24 pF 93
晶振并联电容 C0 7 pF 93
fINTOSC 频率,INTOSC1 和 INTOSC2 fINTOSC 9.7 10 10.3 MHz 94
室温下的频率稳定性 fINTOSC-STABILITY -0.1 0.1 % 30°C,标称 VDD 95
VDD 上的频率稳定性 fINTOSC-STABILITY -0.2 0.2 % 30°C 95
频率稳定性 fINTOSC-STABILITY -3 3 % 95
ADCCLK(源自 PERx.SYSCLK) ADCCLK 5 50 MHz 123
有效输出电压范围 VOUT (RL=5kΩ) VOUT 0.3 V RL = 5kΩ 136
有效输出电压范围 VOUT (RL=1kΩ) VOUT 0.6 V RL = 1kΩ 136
负载调整率 -1 1 mV/V 136
偏移量误差 -10 10 mV 中点 136
增益误差 -2.5 2.5 FSR 百分比 136
比较器输入 (CMPINxx) 范围 0 V 143
以输入为基准的偏移量误差 -20 20 mV 低共模,反相输入设置为 50mV 143
CMPSS DAC 静态偏移量误差 -25 25 mV 144
CMPSS DAC 静态增益误差 -2 2 FSR 百分比 144
CMPSS DAC 静态 INL INL -16 16 LSB 已更正端点 144
CMPSS DAC 输出干扰 -100 100 LSB 由同一 CMPSS 模块内的比较器跳闸或 CMPSS DAC 代码更改引起的误差 144
VDAC 负载 6 8 10 kΩ 当 VDAC 为基准时 144
VBOR-GB VDDIO BOR 保护频带 VBOR-GB 0.1 V 59

CAD (KiCad official)

  • Symbol: F280049CPMS
  • Footprint: Package_QFP:LQFP-64_10x10mm_P0.5mm
  • 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
  • 3D model files: f280049cpms-etched.step / f280049cpms-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); f280049cpms.step / f280049cpms.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (277 pp, sha256 867e7bb5ada6819c, retrieved 2026-11-10, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF