3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLKS32MC071CBT8
LINKOSEMI · Microcontroller Units (MCUs/MPUs/SOCs) · TQFP-48
LKS32MC071CBT8 from LINKOSEMI, in a TQFP-48. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | P0_0 | bidirectional | GPIO P0.0 multiplexed with CLKO, MCPWM_BKIN0, UART0_RXD, SPI_DI, CLUOUT0, ADC01_CH4, DAC0_OUT, DAC1_OUT, FLT, EXTI0 and WK0; internal 10kΩ pull-up that can be disabled in software. |
| 2 | P0_2 / RST_n | bidirectional | Reset pin RST_n (default function of P0.2, which can be switched to GPIO); datasheet recommends a 10nF-100nF capacitor to ground and a 10k-20k pull-up between RSTN and AVDD, with a 100nF capacitor if an external pull-up is used, and RSTN has a fixed internal 100kΩ pull-up. |
| 3 | GND | power_in | Chip ground; the datasheet strongly recommends connecting multiple ground pins together on the PCB. |
| 4 | AVDD | power_in | Chip supply voltage, specified range 2.5-5.5 V. |
| 5 | P3_2 | bidirectional | GPIO P3.2 multiplexed with MCPWM_CH3P (PWM channel 3 high side) and CLUOUT2. |
| 6 | P0_3 | bidirectional | GPIO P0.3 multiplexed with MCPWM_CH4P, SCL, TIM2_CH0, ADC01_CH7 and EXTI3; internal 10kΩ pull-up that can be disabled in software. |
| 7 | P0_4 | bidirectional | GPIO P0.4 multiplexed with MCPWM_CH4N, SDA, TIM2_CH1 and ADC01_CH8; internal 10kΩ pull-up that can be disabled in software. |
| 8 | P0_5 | bidirectional | GPIO P0.5 multiplexed with HALL_IN0, MCPWM_CH5P, QEP0_Z and ADC01_CH9. |
| 9 | P0_6 | bidirectional | GPIO P0.6 multiplexed with HALL_IN1, MCPWM_CH5N, CAN_RX, UART1_RXD, SCL, TIM1_CH0, CMP2_IN, FLT, EXTI4 and WK2; internal 10kΩ pull-up that can be disabled in software. |
| 10 | P0_7 | bidirectional | GPIO P0.7 multiplexed with HALL_IN2, MCPWM_BKIN1, UART1_TXD, SDA, TIM1_CH1, CAN_TX, CMP2_IP0 and FLT; internal 10kΩ pull-up that can be disabled in software. |
| 11 | P2_11 | bidirectional | GPIO P2.11 multiplexed with MCPWM_CH1P, TIM2_CH0 and CMP2_IP1. |
| 12 | P2_12 | bidirectional | GPIO P2.12 multiplexed with MCPWM_CH1N, SPI_CS, TIM2_CH1, ADC_TRIGGER0, CLUOUT3 and EXTI6. |
| 13 | P0_11 | bidirectional | GPIO P0.11 multiplexed with HALL_IN0, TIM3_CH0, ADC1_CH11, CMP0_IP1, FLT, EXTI7 and WK3. |
| 14 | P0_12 | bidirectional | GPIO P0.12 multiplexed with HALL_IN1, TIM3_CH1, CAN_RX, ADC1_CH12, CMP0_IP2 and FLT. |
| 15 | P0_13 | bidirectional | GPIO P0.13 multiplexed with HALL_IN2, QEP0_Z, CAN_TX, ADC1_CH13, CMP0_IP3 and FLT. |
| 16 | P0_14 | bidirectional | GPIO P0.14 multiplexed with CMP0_OUT, MCPWM_BKIN1, UART0_TXD, SPI_CLK, SCL, TIM0_CH1, QEP1_Z, ADC_TRIGGER0, SIF, CLUOUT0, ADC0_CH10, CMP0_IP4, FLT, EXTI8 and WK4; internal 10kΩ pull-up that can be disabled in software. |
| 17 | P0_15 | bidirectional | GPIO P0.15 multiplexed with CMP2_OUT, MCPWM_CH0P, UART0_RXD, SPI_DO, SDA, TIM0_CH0, ADC_TRIGGER1, CMP0_IN, FLT and EXTI9; internal 10kΩ pull-up that can be disabled in software. |
| 18 | P1_0 | bidirectional | GPIO P1.0 multiplexed with MCPWM_CH0N, UART0_TXD, SPI_DI, TIM0_BKIN and EXTI10; internal 10kΩ pull-up that can be disabled in software. |
| 19 | P1_3 | bidirectional | GPIO P1.3 multiplexed with TIM3_CH1 and ADC01_CH5; internal 10kΩ pull-up that can be disabled in software. |
| 20 | P3_5 | input | Op-amp 0 non-inverting input (OPA0_IP) on P3.5. |
| 21 | P3_7 | input | Op-amp 0 inverting input (OPA0_IN) on P3.7. |
| 22 | P2_7 | bidirectional | GPIO P2.7 multiplexed with CLKO, UART0_TXD, TIM0_CH0, TIM3_CH1, ADC_TRIGGER1, CAN_TX, CLUOUT1, ADC0_CH11, OPAx_OUT (op-amp output buffer), LDO15 (1.5 V LDO output), REF (reference voltage), EXTI11 and WK6; internal 10kΩ pull-up that can be disabled in software. |
| 23 | P3_0 | input | Op-amp 1 non-inverting input (OPA1_IP) on P3.0. |
| 24 | P3_1 | input | Op-amp 1 inverting input (OPA1_IN) on P3.1. |
| 25 | P2_8 | bidirectional | GPIO P2.8 multiplexed with UART1_RXD, SPI_DO, TIM3_CH0 and OSC_IN (external crystal pin); internal 10kΩ pull-up that can be disabled in software. |
| 26 | P3_9 | bidirectional | GPIO P3.9 multiplexed with UART1_TXD, TIM3_CH1 and OSC_OUT (external crystal pin); internal 10kΩ pull-up that can be disabled in software. |
| 27 | P1_4 | bidirectional | GPIO P1.4 multiplexed with MCPWM_CH0P and QEP0_Z. |
| 28 | P1_5 | bidirectional | GPIO P1.5 multiplexed with MCPWM_CH0N. |
| 29 | P1_6 | bidirectional | GPIO P1.6 multiplexed with MCPWM_CH1P. |
| 30 | P1_7 | bidirectional | GPIO P1.7 multiplexed with MCPWM_CH1N. |
| 31 | P1_8 | bidirectional | GPIO P1.8 multiplexed with MCPWM_CH2P. |
| 32 | P1_9 | bidirectional | GPIO P1.9 multiplexed with MCPWM_CH2N. |
| 33 | P1_10 | bidirectional | GPIO P1.10 multiplexed with MCPWM_CH3P, UART0_RXD, SCL, TIM0_CH0, ADC_TRIGGER0, ADC0_CH13 and EXTI12; internal 10kΩ pull-up that can be disabled in software. |
| 34 | P1_11 | bidirectional | GPIO P1.11 multiplexed with MCPWM_CH3N, UART0_TXD, SDA, TIM0_CH1, ADC_TRIGGER1, SIF and CLUOUT2; internal 10kΩ pull-up that can be disabled in software. |
| 35 | P3_10 | bidirectional | GPIO P3.10 multiplexed with MCPWM_CH4P and OPA2_IP (op-amp 2 non-inverting input). |
| 36 | P3_11 | bidirectional | GPIO P3.11 multiplexed with MCPWM_CH4N and OPA2_IN (op-amp 2 inverting input). |
| 37 | P2_9 | bidirectional | GPIO P2.9 multiplexed with MCPWM_CH5P, SPI_DI, SCL, ADC0_CH12 and CMP0_IP0; internal 10kΩ pull-up that can be disabled in software. |
| 38 | P2_10 | bidirectional | GPIO P2.10 multiplexed with MCPWM_CH5N, SPI_DO and SDA; internal 10kΩ pull-up that can be disabled in software. |
| 39 | P3_14 | input | Op-amp 3 inverting input (OPA3_IN) on P3.14. |
| 40 | P3_15 | input | Op-amp 3 non-inverting input (OPA3_IP) on P3.15. |
| 41 | P2_1 | bidirectional | GPIO P2.1 multiplexed with SPI_CLK, ADC1_CH10 and CMP1_IP0. |
| 42 | P2_2 | bidirectional | GPIO P2.2 multiplexed with QEP1_Z and CMP1_IN (comparator 1 inverting input). |
| 43 | P2_3 | bidirectional | GPIO P2.3 multiplexed with CMP1_OUT, MCPWM_BKIN0, SPI_CS, TIM0_CH1, QEP0_Z, CLUOUT3, FLT and EXTI13. |
| 44 | P2_4 | bidirectional | GPIO P2.4 multiplexed with CMP0_OUT, HALL_IN0, MCPWM_CH2P, UART1_RXD, SPI_CLK, TIM1_CH0, TIM2_CH0, ADC_TRIGGER0, CAN_RX, CMP1_IP1, FLT, EXTI14 and WK5; internal 10kΩ pull-up that can be disabled in software. |
| 45 | P2_5 | bidirectional | GPIO P2.5 multiplexed with CMP1_OUT, HALL_IN1, MCPWM_CH2N, UART1_TXD, SPI_DO, TIM1_CH1, TIM2_CH1, ADC_TRIGGER1, CAN_TX, CMP1_IP2 and FLT; internal 10kΩ pull-up that can be disabled in software. |
| 46 | P2_6 | bidirectional | GPIO P2.6 multiplexed with CMP2_OUT, HALL_IN2, MCPWM_CH3P, TIM0_BKIN, TIM3_CH0, ADC_TRIGGER0, SIF, CLUOUT0, CMP1_IP3 and FLT; internal 10kΩ pull-up that can be disabled in software. |
| 47 | P2_14 | bidirectional | GPIO P2.14 multiplexed with SWCLK (SWD clock), SPI_DI and SCL; internal 10kΩ pull-up that can be disabled in software. |
| 48 | P2_15 | bidirectional | GPIO P2.15 multiplexed with SWDIO (SWD data), UART0_RXD, SPI_CS, SDA, TIM2_CH1, CLUOUT1, EXTI15 and WK7; internal 10kΩ pull-up that can be disabled in software. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | LINKOSEMI |
| Package | TQFP-48 |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply voltage | AVDD | -0.3 | 6 | V | 65 | ||
| Pre-driver supply voltage | VCC | -0.3 | 25 | V | LKS07x with 6N driver | 65 | |
| Pre-driver supply voltage | VCC | -0.3 | 40 | V | LKS07x with 3P3N driver | 65 | |
| LDO supply voltage | VCCLDO | -0.3 | 25 | V | 074DO 中 LDO 供电的引脚 | 65 | |
| Operating temperature | -40 | 105 | ˚C | 65 | |||
| Storage temperature | -40 | 150 | ˚C | 65 | |||
| Junction temperature | 125 | °C | 65 | ||||
| Lead temperature | 260 | °C | 焊接,10 秒 | 65 | |||
| ESD (HBM) | -6000 | 6000 | V | MIL-STD-883J Method 3015.9 | 65 | ||
| Latch-up current | -200 | 200 | mA | 85℃ | 65 | ||
| GPIO signal input voltage range | VIN | -0.3 | 6 | V | 65 | ||
| Max injection current per GPIO | IINJ_PAD | -11.2 | 11.2 | mA | 65 | ||
| Max injection current, all GPIO | IINJ_SUM | -50 | 50 | mA | 65 | ||
| Power supply voltage | AVDD | 2.5 | 5 | 5.5 | V | 65 | |
| Analog operating voltage | AVDDA | 2.8 | 5 | 5.5 | V | REF2VDD=0,ADC 选择 2.4V 内部基准 | 65 |
| Analog operating voltage | AVDDA | 2.4 | 5 | 5.5 | V | REF2VDD=1,ADC 选择 AVDD 为基准 | 65 |
| Pre-driver supply voltage | VCC | 4.5 | 20 | V | 071DO/074DO | 65 | |
| Digital IO input high voltage | VIH | 3.06 | V | AVDD 5V | 66 | ||
| Digital IO input high voltage | VIH | 2.07 | V | AVDD 3.3V | 66 | ||
| Digital IO input low voltage | VIL | 0.8 | V | AVDD 3.3V | 66 | ||
| Digital IO output low voltage | VOL | 0.5 | V | 最大驱动电流 11.2mA | 66 | ||
| Digital IO input high current, current consumption | IIH | 1 | uA | AVDD 5V / 3.3V | 66 | ||
| Digital IO input low current, current consumption | IIL | -1 | uA | AVDD 5V / 3.3V | 66 | ||
| Pull-up resistance | Rpup | 8 | 12 | kΩ | 66 | ||
| Resistance between IO and internal analog circuit | Rio-ana | 100 | 200 | Ω | 66 | ||
| Digital IO input capacitance | CIN | 10 | pF | AVDD 5V / 3.3V | 66 |
CAD (KiCad official)
- Symbol:
LKS32MC071CBT8 - Footprint:
Package_QFP:TQFP-48_7x7mm_P0.5mm - 3D model: TQFP-48 (KiCad packages3D, STEP)
- 3D model files:
lks32mc071cbt8-etched.step/lks32mc071cbt8-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lks32mc071cbt8.step/lks32mc071cbt8.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: LINKOSEMI datasheet (91 pp, sha256
d7b5cc2187fa2830, retrieved 2026-11-13, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).