Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

KSZ8842-16MVLI-TR

Microchip Tech · Ethernet Transceivers · LQFP-128(14x14)

KSZ8842-16MVLI-TR from Microchip Tech, in a LQFP-128(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TEST_EN input Test enable; for normal operation pull down to ground.
2 SCAN_EN input Scan test scan mux enable; for normal operation pull down to ground.
3 P1LED2 output Port 1 LED indicator, output with internal pull-up; function depends on SGCR5 bits.
4 P1LED1 output Port 1 LED indicator, output with internal pull-up; function depends on SGCR5 bits.
5 P1LED0 output Port 1 LED indicator, output with internal pull-up; function depends on SGCR5 bits.
6 P2LED2 output Port 2 LED indicator, output with internal pull-up; function depends on SGCR5 bits.
7 P2LED1 output Port 2 LED indicator, output with internal pull-up; function depends on SGCR5 bits.
8 P2LED0 output Port 2 LED indicator, output with internal pull-up; function depends on SGCR5 bits.
9 DGND power_in Digital ground.
10 VDDIO power_in 3.3V digital VDDIO input power supply for IO with well decoupling capacitors.
11 RDYRTNN input Ready return not; asserted by host to complete synchronous reads in VLBus-like mode, or driven low for wait states in 32-bit burst mode.
12 BCLK input Local bus clock for synchronous bus systems; maximum frequency is 50 MHz; tie low or unconnected in asynchronous mode.
13 NC unconnected No connect.
14 NC unconnected No connect.
15 SRDYN output Synchronous ready not; falling edge indicates ready in VLBus-like mode, synchronous to BCLK.
16 INTRN output Active-low interrupt to host CPU; requires an external 4.7 kΩ pull-up resistor.
17 LDEVN output Active-low output asserted when AEN is low and A15-A4 decode to the programmed base address.
18 RDN input Asynchronous active-low read strobe.
19 EECS output EEPROM chip select.
20 ARDY output Asynchronous ready used to extend bus access cycles; requires an external 4.7 kΩ pull-up resistor.
21 CYCLEN input Cycle signal; follows the addressing cycle to signal the command cycle in VLBus-like mode.
22 P2LED3 output Port 2 LED indicator with internal pull-down; see pins 6, 7 and 8.
23 DGND power_in Digital IO ground.
24 VDDCO power_out 1.2V digital core voltage output from the internal LDO; supplies VDDC, VDDA and VDDAP; do not connect an external supply.
25 VLBUSN input Bus mode select: pull-down or float selects synchronous mode; pull-up selects 8/16-bit asynchronous or EISA-like burst mode.
26 EEEN input EEPROM enable; EEPROM is enabled and connected when pulled up, and disabled when pulled down or no connect.
27 P1LED3 output Port 1 LED indicator with internal pull-down; see pins 3, 4 and 5.
28 EEDO output EEPROM data out; connected to the DI input of the serial EEPROM.
29 EESK output EEPROM serial clock to load configuration; 4 µs cycle at 25 MHz on-chip bus speed or 800 ns at 125 MHz.
30 EEDI input EEPROM data in; connected to the DO output of the serial EEPROM when EEEN is pulled up.
31 SWR input Synchronous write/read; write cycles when high and read cycles when low.
32 AEN input Address enable; active-low address qualifier for address decoding.
33 WRN input Asynchronous active-low write strobe.
34 DGND power_in Digital IO ground.
35 ADSN input Address strobe not; the rising edge latches A15-A1 and AEN.
36 PWRDN input Full-chip power-down; low powers down the chip, high or floating is normal operation.
37 AGND power_in Analog ground.
38 VDDA power_in 1.2V analog VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor.
39 AGND power_in Analog ground.
40 NC unconnected No connect.
41 NC unconnected No connect.
42 AGND power_in Analog ground.
43 VDDA power_in 1.2V analog VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor.
44 NC unconnected No connect.
45 RXP1 bidirectional Port 1 physical receive (MDI) or transmit signal, + differential.
46 RXM1 bidirectional Port 1 physical receive (MDI) or transmit signal, - differential.
47 AGND power_in Analog ground.
48 TXP1 bidirectional Port 1 physical transmit (MDI) or receive (MDI-X) signal, + differential.
49 TXM1 bidirectional Port 1 physical transmit (MDI) or receive (MDI-X) signal, - differential.
50 VDDATX power_in 3.3V analog VDD input power supply with well decoupling capacitors.
51 VDDARX power_in 3.3V analog VDD input power supply with well decoupling capacitors.
52 RXM2 bidirectional Port 2 physical receive (MDI) or transmit (MDI-X) signal, - differential.
53 RXP2 bidirectional Port 2 physical receive (MDI) or transmit (MDI-X) signal, + differential.
54 AGND power_in Analog ground.
55 TXM2 bidirectional Port 2 physical receive (MDI) or transmit (MDI-X) signal, - differential.
56 TXP2 bidirectional Port 2 physical receive (MDI) or transmit (MDI-X) signal, + differential.
57 VDDA power_in 1.2V analog VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor.
58 AGND power_in Analog ground.
59 NC unconnected No connect.
60 NC unconnected No connect.
61 ISET output Sets physical transmit output current; pull down with a 3.01 kΩ 1% resistor to ground.
62 AGND power_in Analog ground.
63 VDDAP power_in 1.2V analog VDD for PLL supplied from VDDCO (pin 24) through an external ferrite bead and capacitor.
64 AGND power_in Analog ground.
65 X1 input 25 MHz crystal or oscillator clock input; clock requirement ±50 ppm; a 3.3V tolerant oscillator may drive X1.
66 X2 output Crystal connection for the 25 MHz clock; no connect when an oscillator is used.
67 RSTN input Hardware reset, active-low; requires a minimum of 10 ms low after the 3.3V supply is stable.
68 A15 input Address bit 15 input.
69 A14 input Address bit 14 input.
70 A13 input Address bit 13 input.
71 A12 input Address bit 12 input.
72 A11 input Address bit 11 input.
73 A10 input Address bit 10 input.
74 A9 input Address bit 9 input.
75 A8 input Address bit 8 input.
76 A7 input Address bit 7 input.
77 A6 input Address bit 6 input.
78 DGND power_in Digital IO ground.
79 VDDIO power_in 3.3V digital VDDIO input power supply for IO with well decoupling capacitors.
80 A5 input Address bit 5 input.
81 A4 input Address bit 4 input.
82 A3 input Address bit 3 input.
83 A2 input Address bit 2 input.
84 A1 input Address bit 1 input.
85 NC unconnected No connect.
86 NC unconnected No connect.
87 BE1N input Active-low byte enable 1 for data byte 1; don't care in 8-bit bus mode.
88 BE0N input Active-low byte enable 0 for data byte 0; internally inverted and connected to BE1N in 8-bit bus mode.
89 NC unconnected No connect.
90 DGND power_in Digital core ground.
91 VDDC power_in 1.2V digital core VDD supplied from VDDCO (pin 24) through an external ferrite bead and capacitor.
92 VDDIO power_in 3.3V digital VDDIO input power supply for IO with well decoupling capacitors.
93 NC unconnected No connect.
94 NC unconnected No connect.
95 NC unconnected No connect.
96 NC unconnected No connect.
97 NC unconnected No connect.
98 NC unconnected No connect.
99 NC unconnected No connect.
100 NC unconnected No connect.
101 NC unconnected No connect.
102 NC unconnected No connect.
103 NC unconnected No connect.
104 NC unconnected No connect.
105 NC unconnected No connect.
106 NC unconnected No connect.
107 DGND power_in Digital IO ground.
108 VDDIO power_in 3.3V digital VDDIO input power supply for IO with well decoupling capacitors.
109 NC unconnected No connect.
110 D15 bidirectional Data bus bit 15.
111 D14 bidirectional Data bus bit 14.
112 D13 bidirectional Data bus bit 13.
113 D12 bidirectional Data bus bit 12.
114 D11 bidirectional Data bus bit 11.
115 D10 bidirectional Data bus bit 10.
116 D9 bidirectional Data bus bit 9.
117 D8 bidirectional Data bus bit 8.
118 D7 bidirectional Data bus bit 7.
119 D6 bidirectional Data bus bit 6.
120 D5 bidirectional Data bus bit 5.
121 D4 bidirectional Data bus bit 4.
122 D3 bidirectional Data bus bit 3.
123 DGND power_in Digital IO ground.
124 DGND power_in Digital core ground.
125 VDDIO power_in 3.3V digital VDDIO input power supply for IO with well decoupling capacitors.
126 D2 bidirectional Data bus bit 2.
127 D1 bidirectional Data bus bit 1.
128 D0 bidirectional Data bus bit 0.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package LQFP-128(14x14)
Category Communication Interface Chip
Pins 128

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input High Voltage VIH 2 V 110
Input Low Voltage VIL 0.8 V 110
Input Current IIN -10 10 μA VIN = GND ~ VDDIO 110
Output High Voltage VOH 2.4 V IOH = -8 mA 110
Output Low Voltage VOL 0.4 V IOL = 8 mA 110
Output Tri-State Leakage /IOZ/ 10 μA 110
Peak Differential Output Voltage VO -0.95 1.05 V 100Ω termination on the differential output. 110
Output Voltage Imbalance VIMB 2 % 100Ω termination on the differential output. 110
Rise/Fall Time tr/tf 3 5 ns 110
Rise/Fall Time Imbalance 0 0.5 ns 110
Duty Cycle Distortion -0.25 0.25 ns 110
Overshoot 5 % 110
Output Jitter (100BASE-TX) 0.7 1.4 ns Peak-to-peak 110
Output Jitter (10BASE-T) 1.8 3.5 ns Peak-to-peak 110
Supply Voltage (VDDATX, VDDARX, VDDIO) -0.5 4 V 109
Input Voltage (all inputs) -0.5 5 V 109
Output Voltage (all outputs) -0.5 4 V 109
Storage Temperature TS -55 150 °C 109
Lead Temperature (Soldering) 270 °C Soldering, 10 sec 109
Supply Voltage (VDDATX, VDDARX, VDDIO) 3.1 3.5 V 109
Ambient Operating Temperature (industrial option) TA -40 85 °C Industrial Temperature Range (Features, page 1) 1
Maximum Junction Temperature TJ 125 °C 109
Thermal Resistance (junction-to-ambient) ΘJA 42.91 °C/W Note 5-1: no heat spreader; air velocity 0 m/s 109
Thermal Resistance (junction-to-case) ΘJC 19.6 °C/W Note 5-1: no heat spreader; air velocity 0 m/s 109
Stable supply voltages to reset high tSR 10 ms 121
Address valid to RDN/WRN active t1 0 ns A1-A15, AEN, BExN[3:0] valid to RDN, WRN active 111
Address hold after RDN inactive t2 0 ns Assume ADSN tied Low 111
Address hold after WRN inactive t2 1 ns Assume ADSN tied Low 111
Read data valid to ARDY rising t3 0.8 ns 111
Read data hold after RDN inactive t4 4 ns 111
Write data setup to WRN inactive t5 4 ns 111
Write data hold after WRN inactive t6 2 ns 111
Read active to ARDY Low t7 8 ns 111
Write inactive to ARDY Low t8 8 ns 111

CAD (KiCad official)

  • Symbol: KSZ8842-16MVLI-TR
  • Footprint: Package_QFP:LQFP-128_14x14mm_P0.4mm
  • 3D model: LQFP-128(14x14) (KiCad packages3D, STEP)
  • 3D model files: ksz8842-16mvli-tr-etched.step / ksz8842-16mvli-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ksz8842-16mvli-tr.step / ksz8842-16mvli-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (132 pp, sha256 36e29b760fb0e430, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF