component
FM93C66A-SO-T-G
Public Made by Adomby adom
FUDAN MICRO EEPROM, SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownFM93C66A-SO-T-G
FUDAN MICRO · EEPROM · SOP-8
FM93C66A-SO-T-G from FUDAN MICRO, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | Chip Select input; device is enabled when CS is brought high, and DO outputs Ready/Busy status of the part following a write, erase, or program cycle if CS is held low for minimum 200 ns to 250 ns depending on supply voltage. |
| 2 | DI | input | Serial Data Input for three-wire serial interface; accepts start bit (first logic "1" read during rising edge of SK) followed by op-code bits and address bits for instruction execution. |
| 3 | DO | output | Serial Data Output for three-wire serial interface; outputs data synchronized with rising edges of SK during read operations, and outputs Ready/Busy status (logic "0" for busy, logic "1" for ready) when CS is brought high during write/erase/program cycles. |
| 4 | GND | power_in | Ground reference connection. |
| 5 | NC | unconnected | No connection; pin should be left unconnected. |
| 6 | VCC | power_in | Power supply voltage input; operating range 1.7V to 5.5V with maximum operating voltage of 6.25V. |
| 7 | SK | input | Serial Clock input for three-wire serial interface; clock frequency range 1 MHz (at 1.7V to 2.5V) to 2 MHz (at 2.5V to 5.5V); synchronizes data input and output transitions. |
| 8 | ORG | input | Organization Select input; when connected to VCC or left unconnected, selects x16 (word) organization; when connected to GND, selects x8 (byte) organization; should be set to VSS or VCC for minimum standby power consumption. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FUDAN MICRO |
| Package | SOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | 1.7 | 5.5 | V | TA = -40°C to +85°C | 12 | |
| Operating Temperature | -55 | 125 | °C | 3 | |||
| Storage Temperature | -65 | 150 | °C | 3 | |||
| Voltage on Any Pin with Respect to Ground | -1 | 7 | V | 3 | |||
| Maximum Operating Voltage | 6.25 | V | 3 | ||||
| DC Output Current | 5 | mA | 3 | ||||
| ICC Supply Current | ICC | 2 | mA | VCC = 5.0V, fsk = 2.0 MHz CS = VIH, DO = open | 12 | ||
| ICC Supply Current | ICC | 1 | mA | VCC = 1.7V, fsk = 1.0 MHz | 12 | ||
| ISB Standby Current | ISB | 15 | µA | VCC=5V CS = SK = GND, ORG = VCC/GND | 12 | ||
| ISB Standby Current | ISB | 2 | µA | VCC = 1.7V | 12 | ||
| Input Leakage | ILI | -1 | 1 | µA | 0V ≤ VIN ≤ Vcc | 12 | |
| Output Leakage | ILO | -1 | 1 | µA | 0V ≤ VOUT ≤ Vcc ; DO = Hi-Z | 12 | |
| Input Low Voltage | VIL | -0.45 | V | 12 | |||
| Output Low Voltage | VOL | 0.4 | V | VCC = 5V IOL = 2.1 mA | 12 | ||
| Output Low Voltage | VOL | 0.2 | V | VCC = 1.7V IOL = 100 µA | 12 | ||
| Input Capacitance | CIN | 6 | pF | VIN = 0V, f = 1 MHz | 12 | ||
| Output Capacitance | COUT | 8 | pF | VOUT = 0V, f = 1 MHz | 12 | ||
| SK Clock Frequency | fBSK | 1 | MHz | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| SK Clock Frequency | fBSK | 2 | MHz | 2.5V < Vcc ≤ 5.5V | 13 | ||
| SK Low Time | tBSKL | 250 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| SK Low Time | tBSKL | 200 | ns | 2.5V < Vcc ≤ 5.5V | 13 | ||
| SK High Time | tBSKHB | 250 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| SK High Time | tBSKHB | 200 | ns | 2.5V < Vcc ≤ 5.5V | 13 | ||
| Minimum CS Low | tBCS | 250 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| Minimum CS Low | tBCS | 200 | ns | 2.5V < Vcc ≤ 5.5V | 13 | ||
| CS Setup Time | tBCSSB | 50 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| CS Hold Time | tBCSH | 0 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| DI Setup Time | tDISB | 100 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| DI Setup Time | tDISB | 50 | ns | 2.5V < Vcc ≤ 5.5V | 13 | ||
| DI Hold Time | tBDIH | 100 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| DI Hold Time | tBDIH | 50 | ns | 2.5V < Vcc ≤ 5.5V | 13 | ||
| Output Delay to 1 | tBPD1 | 400 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| Output Delay to 1 | tBPD1 | 200 | ns | 2.5V < Vcc ≤ 5.5V | 13 | ||
| Output Delay to 0 | tBPD0 | 400 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| Output Delay to 0 | tBPD0 | 200 | ns | 2.5V < Vcc ≤ 5.5V | 13 | ||
| CS to Status Valid | tBSVB | 400 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| CS to Status Valid | tBSVB | 200 | ns | 2.5V < Vcc ≤ 5.5V | 13 | ||
| CS to DO in High | tBDFB | 200 | ns | 1.7V ≤ Vcc ≤ 2.5V | 13 | ||
| CS to DO in High | tBDFB | 100 | ns | 2.5V < Vcc ≤ 5.5V | 13 | ||
| Write Cycle | tBWRB | 5 | ms | 13 | |||
| Endurance | 1e+06 | Write Cycles | 3.3V, 25°C | 13 |
CAD (KiCad official)
- Symbol:
FM93C66A-SO-T-G - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
fm93c66a-so-t-g-etched.step/fm93c66a-so-t-g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);fm93c66a-so-t-g.step/fm93c66a-so-t-g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FUDAN MICRO datasheet (23 pp, sha256
24f79e252a44ab45, retrieved 2026-10-26, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.2, primaryclaude-haiku-4-5-20251001(text), consensusoff(skipped (clean text read)), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).