component
FSW6860YQFN48G
Public Made by Adomby adom
Full-Way(四方杰芯) , QFN-48L(6x6). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownFSW6860YQFN48G
Full-Way(四方杰芯) · IC · QFN-48L(6x6)
FSW6860YQFN48G from Full-Way(四方杰芯), in a QFN-48L(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | Not connected; leave floating. |
| 2 | S11 | input | Select pin for Port B01/B11 path: L selects Port A1 to B01, H selects Port A1 to B11 (active only when _EN is low). |
| 3 | VCC2 | power_in | Positive supply for the normal-speed channel; the datasheet gives VCC1,VCC2 absolute maximum of -0.3 V to 6.5 V and tests normal-speed DC levels at 3.3 V. |
| 4 | B11 | bidirectional | Analog/digital signal Port 1, normally open contact of the normal-speed SPDT switch. |
| 5 | COMAN | bidirectional | Negative differential signal 1 for the USB 3.1 COM port. |
| 6 | COMAP | bidirectional | Positive differential signal 1 for the USB 3.1 COM port. |
| 7 | COMBN | bidirectional | Negative differential signal 2 for the USB 3.1 COM port. |
| 8 | COMBP | bidirectional | Positive differential signal 2 for the USB 3.1 COM port. |
| 9 | COMCN | bidirectional | Negative differential signal 3 for the USB 3.1 COM port. |
| 10 | COMCP | bidirectional | Positive differential signal 3 for the USB 3.1 COM port. |
| 11 | COMDN | bidirectional | Negative differential signal 4 for the USB 3.1 COM port. |
| 12 | COMDP | bidirectional | Positive differential signal 4 for the USB 3.1 COM port. |
| 13 | GND2 | power_in | Power ground. |
| 14 | COMEN | bidirectional | Negative differential signal 5 for the USB 3.1 COM port. |
| 15 | COMEP | bidirectional | Positive differential signal 5 for the USB 3.1 COM port. |
| 16 | SEL | input | Select pin for the high-speed mux: L connects Port COM to Port A, H connects Port COM to Port B (internal pull-down 2 MΩ). |
| 17 | _EN | input | Active-low enable for the high-speed channel; high disables the switch into shutdown (internal pull-up 2 MΩ), with logic thresholds VIH 1.6 V min and VIL 0.4 V max at VCC 1.8-4.5 V. |
| 18 | DA4P | bidirectional | Positive differential signal 4 for the USB 3.1 Port A. |
| 19 | DA4N | bidirectional | Negative differential signal 4 for the USB 3.1 Port A. |
| 20 | DA2P | bidirectional | Positive differential signal 2 for the USB 3.1 Port A. |
| 21 | DA2N | bidirectional | Negative differential signal 2 for the USB 3.1 Port A. |
| 22 | DB3P | bidirectional | Positive differential signal 3 for the USB 3.1 Port B. |
| 23 | DB3N | bidirectional | Negative differential signal 3 for the USB 3.1 Port B. |
| 24 | GND3 | power_in | Power ground. |
| 25 | DB4P | bidirectional | Positive differential signal 4 for the USB 3.1 Port B. |
| 26 | DB4N | bidirectional | Negative differential signal 4 for the USB 3.1 Port B. |
| 27 | DA3P | bidirectional | Positive differential signal 3 for the USB 3.1 Port A. |
| 28 | DA3N | bidirectional | Negative differential signal 3 for the USB 3.1 Port A. |
| 29 | DB2P | bidirectional | Positive differential signal 2 for the USB 3.1 Port B. |
| 30 | DB2N | bidirectional | Negative differential signal 2 for the USB 3.1 Port B. |
| 31 | DB1P | bidirectional | Positive differential signal 1 for the USB 3.1 Port B. |
| 32 | DB1N | bidirectional | Negative differential signal 1 for the USB 3.1 Port B. |
| 33 | DB0P | bidirectional | Positive differential signal 0 for the USB 3.1 Port B. |
| 34 | DB0N | bidirectional | Negative differential signal 0 for the USB 3.1 Port B. |
| 35 | VCC3 | power_in | Positive supply for the high-speed channel; absolute maximum is -0.5 V to +5.5 V and the high-speed electrical characteristics are specified at VCC = 3 V. |
| 36 | GND4 | power_in | Power ground. |
| 37 | NC | unconnected | Not connected; leave floating. |
| 38 | DA1P | bidirectional | Positive differential signal 1 for the USB 3.1 Port A. |
| 39 | DA1N | bidirectional | Negative differential signal 1 for the USB 3.1 Port A. |
| 40 | DA0P | bidirectional | Positive differential signal 0 for the USB 3.1 Port A. |
| 41 | DA0N | bidirectional | Negative differential signal 0 for the USB 3.1 Port A. |
| 42 | B02 | bidirectional | Analog/digital signal Port 2, normally closed contact of the normal-speed SPDT switch. |
| 43 | A2 | bidirectional | Common signal Port 2 of the normal-speed SPDT switch. |
| 44 | B12 | bidirectional | Analog/digital signal Port 2, normally open contact of the normal-speed SPDT switch. |
| 45 | VCC2 | power_in | Positive supply for the normal-speed channel; the datasheet gives VCC1,VCC2 absolute maximum of -0.3 V to 6.5 V. |
| 46 | S12 | input | Select pin for Port B02/B12: L selects Port A2 to B02, H selects Port A2 to B12 (active only when _OE is low). |
| 47 | B01 | bidirectional | Analog/digital signal Port 1, normally closed contact of the normal-speed SPDT switch. |
| 48 | A1 | bidirectional | Common signal Port 1 of the normal-speed SPDT switch. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Full-Way(四方杰芯) |
| Package | QFN-48L(6x6) |
| Category | |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | -55 | 150 | °C | 5 | |||
| Junction Temperature | 125 | °C | 5 | ||||
| Supply Voltage to Ground Potential (High Speed Channel) | VCC3 | -0.5 | 5.5 | V | 5 | ||
| Super Speed Data Channel TX / RX | -0.5 | 3.8 | V | 5 | |||
| DC Input Voltage | -0.5 | V | Upper limit printed as VCC3 | 5 | |||
| DC Output Current | 50 | mA | 5 | ||||
| Power Dissipation | 300 | mW | 6 | ||||
| Supply Voltage (Normal Speed Channel) | VCC1,VCC2 | -0.3 | 6.5 | V | 6 | ||
| Control Input Voltage | -0.3 | 6.5 | V | 6 | |||
| Continuous Current Through A1, B01, B11 | -100 | 100 | mA | 6 | |||
| Continuous Current Through A2, B02, B12 | -100 | 100 | mA | 6 | |||
| Peak Current Through A1, B01, B11 | -200 | 200 | mA | pulsed at 1ms 50% duty cycle | 6 | ||
| Thermal resistance | 350 | °C/W | 6 | ||||
| Input logic high (High Speed Channel) | VIH | 1.6 | V | VCC=1.8~4.5V | 6 | ||
| Input logic low (High Speed Channel) | VIL | 0.4 | V | VCC=1.8~4.5V | 6 | ||
| VCC Quiescent Current | IQ | 28 | uA | SEL=0 or VCC, _EN=0 | 6 | ||
| Power-down Current | IPO | 1 | uA | SEL=0 or VCC, _EN=VCC | 6 | ||
| Enable Time EN to Output | tEN | 80 | 150 | uS | RL=50Ω CL=0pF VIS= 0.6V | 6 | |
| Disable Time EN to Output | tDIS | 40 | 250 | nS | RL=50Ω CL=0pF VIS= 0.6V | 6 | |
| Turn-On Time SEL to Output | tON | 400 | 1200 | nS | RL=50Ω CL=0pF VIS= 0.6V | 6 | |
| Turn-Off Time SEL to Output | tOFF | 130 | 800 | nS | RL=50Ω CL=0pF VIS= 0.6V | 6 | |
| Break-Before-Make Time | tBBM | 250 | 500 | nS | RL=50Ω CL=0pF VIS= 0.6V | 6 | |
| Input logic high level (Normal Speed Channel) | VIH | 1.6 | V | VCC=3.3~5.5V | 7 | ||
| Input logic high level (Normal Speed Channel) | VIH | 1.4 | V | VCC=1.5~3.3V | 7 | ||
| Input logic low level (Normal Speed Channel) | VIL | 0.6 | V | VCC=3.3~5.5V | 7 | ||
| Input logic low level (Normal Speed Channel) | VIL | 0.4 | V | VCC=1.5~3.3V | 7 | ||
| Supply quiescent current | ICC | 2 | uA | IA=0, VSEL =0 or VSEL =VCC | 7 | ||
| Increase in ICC per input | ICCT | 2 | uA | IA=0, VCC=4.5V, VSEL>1.8 or VSEL<0.5 | 7 | ||
| Off state leakage from A1 to B01 (or B11) | IA | -2 | 2 | uA | VA = 5.5V, VB01(or B11) = 0V | 7 | |
| Off state leakage from A2 to B02 (or B12) | IA | -2 | 2 | uA | VA = 5.5V, VB02(or B12) = 0V | 7 | |
| On-Resistance (range 0 to 0.5V) | RON1 | 3 | 3.5 | Ω | VA=0 ~ 0.5V, IA=30mA | 7 | |
| On-Resistance (range 0.5 to 2.0V) | RON2 | 3.6 | 3.9 | Ω | VA=0.5 ~ 2.0V, IA=30mA | 7 | |
| On-Resistance (range 2.0 to 4.0V) | RON3 | 2.5 | 3.5 | Ω | VA=2.0 ~ 4.0V, IA=30mA | 7 | |
| On-Resistance (range 4.0 to 5.5V) | RON4 | 1.5 | 1.8 | Ω | VA=4.0 ~ 5.5V, IA=30mA | 7 | |
| On-Resistance Matching Between Channels | Δ RON | 0.1 | 0.2 | Ω | VA=0~5.5V, IA=30mA | 7 | |
| On-Resistance for TX/RX | RON_HS | 6.5 | Ω | VIS= 1.5V ION=8mA | 6 | ||
| RON Matching Between Channels (High Speed) | RMATCH | 0.1 | Ω | VIS= 0 to 1.2V ION=8mA | 6 | ||
| EN Internal pull-up resistor | RUP | 2 | MΩ | 6 | |||
| SEL Internal pull-down resistor | RDN | 2 | MΩ | 6 | |||
| Propagation Delay | tPD | 0.25 | nS | RL=50Ω CL=0pF VIS= 0.6V | 6 | ||
| Off Isolation | Off | -39 | dB | RL = 50Ω f = 5GHz VIS= 0.2VPP, See Fig.2 | 6 | ||
| Crosstalk | XTALK | -41 | dB | RL = 50Ω f = 5GHz VIS= 0.2VPP, See Fig.1 | 6 | ||
| -3dB Bandwidth (High Speed) | BW-3dB | 7.5 | GHz | RL=50Ω CL=0pF Signal 0dBm | 6 | ||
| Switch On Capacitance | CON | 1.5 | pF | VBias = 0.2V, f = 1.5GHz | 7 | ||
| Switch Off Capacitance | COFF | 1 | pF | VBias = 0.2V, f = 1.5GHz | 7 | ||
| Turn-On Time (Normal Speed) | TON | 200 | nS | VA=1.5V, CL=35pF, RL=50Ω | 7 | ||
| Turn-Off Time (Normal Speed) | TOFF | 200 | nS | VA=1.5V, CL=35pF, RL=50Ω | 7 | ||
| Break-Before-Make time (Normal Speed) | TBBM | 500 | nS | VA=1.5V, CL=35pF, RL=50Ω | 7 | ||
| -3dB Bandwidth (Normal Speed) | BW | 600 | MHZ | RL=50Ω, CL=0pF | 7 | ||
| Off isolation | OIRR | -81 | dB | F=1KHz, RL=50Ω | 7 | ||
| Off isolation | OIRR | -80 | dB | F=10KHz, RL=50Ω | 7 | ||
| Crosstalk (Normal Speed) | Xtalk | -83 | dB | F=1KHz, RL=50Ω | 7 | ||
| Crosstalk (Normal Speed) | Xtalk | -82 | dB | F=10KHz, RL=50Ω | 7 | ||
| Total Harmonic Distortion | THD | -80 | dB | F=20Hz to 20KHz, VA=600mVp-p @RL=32Ω | 7 | ||
| Off capacitance (Normal Speed) | COFF | 5 | pF | F=100KHz, VCC=3.3 | 7 | ||
| On capacitance (Normal Speed) | CON | 7 | pF | F=100KHz, VCC=3.3 | 7 | ||
| Specified Temperature range | -40 | 85 | °C | Ordering information, FSW6860YQFN48G/TR | 2 |
CAD (KiCad official)
- Symbol:
FSW6860YQFN48G - Footprint:
Package_DFN_QFN:QFN-48-1EP_6x6mm_P0.4mm_EP4.4x4.4mm - 3D model: QFN-48L(6x6), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.9 mm nominal QFN height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
fsw6860yqfn48g-etched.step/fsw6860yqfn48g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);fsw6860yqfn48g.step/fsw6860yqfn48g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Full-Way(四方杰芯) datasheet (11 pp, sha256
76f38ff80d44c134, retrieved 2026-11-09, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).