3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownISL12058IBZ-T
Intersil(Renesas Electronics) · Clock / Timing - Application Specific · SOP-8-150mil
ISL12058IBZ-T from Intersil(Renesas Electronics), in a SOP-8-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Input of an inverting amplifier, intended to be connected to one pin of an external 32.768kHz quartz crystal (or driven by a 0V to VDD 32.768kHz square wave with X2 floating). |
| 2 | X2 | output | Output of an inverting amplifier, intended to be connected to one pin of an external 32.768kHz quartz crystal. |
| 3 | NC | unconnected | No connection; not connected to the die and can be connected to GND or left floating. |
| 4 | GND | power_in | Ground. |
| 5 | SDA | bidirectional | Serial data pin for I2C transfer into and out of the device; open drain output that may be wire-OR'ed, accepts pull-up voltage up to 5.5V. |
| 6 | SCL | input | Serial clock input used to clock all serial data into and out of the device; accepts logic high up to 5.5V. |
| 7 | IRQ/FOUT | output | Open-drain alarm interrupt or frequency output selected via the configuration register, requires an external pull-up (up to 5.5V), and defaults to 32.768kHz output at power-up. |
| 8 | VDD | power_in | Power supply; full operation from 1.8V to 3.6V, timekeeping from 1.4V, with a 0.1µF decoupling capacitor to ground recommended. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Intersil(Renesas Electronics) |
| Package | SOP-8-150mil |
| Category | Clock and Timing |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Main Power Supply | VDD | 1.8 | 3.6 | V | 4 | ||
| Timekeeping Power Supply | VDDT | 1.4 | 1.8 | V | 4 | ||
| Standby Supply Current | IDD1 | 600 | 950 | nA | VDD = 3.6V | 4 | |
| Standby Supply Current | IDD1 | 500 | nA | VDD = 3.0V | 4 | ||
| Timekeeping Current | IDD2 | 400 | 650 | nA | VDD = 1.8V | 4 | |
| Timekeeping Current | IDD2 | 350 | nA | VDD = 1.4V | 4 | ||
| Supply Current With I2C Active at Clock Speed of 400kHz | IDD3 | 15 | 40 | µA | VDD = 3.6V | 4 | |
| Input Leakage Current on SCL | ILI | -100 | 100 | nA | 4 | ||
| I/O Leakage Current on SDA | ILO | -100 | 100 | nA | 4 | ||
| IRQ/FOUT Output Low Voltage | VOL | 0.4 | V | VDD = 1.8V, IOL = 3mA | 4 | ||
| SDA and SCL Input Buffer LOW Voltage | VIL | -0.3 | V | max is 0.3 x VDD | 4 | ||
| SDA and SCL Input Buffer HIGH Voltage | VIH | 5.5 | V | min is 0.7 x VDD | 4 | ||
| SDA Output Buffer LOW Voltage, Sinking 3mA | VOL | 0 | 0.4 | V | VDD > 1.8V, VPULLUP = 5.0V | 4 | |
| SDA and SCL Pin Capacitance | Cpin | 10 | pF | TA = +25°C, f = 1MHz, VDD = 5V, VIN = 0V, VOUT = 0V | 4 | ||
| SCL Frequency | fSCL | 400 | kHz | 4 | |||
| Pulse width Suppression Time at SDA and SCL Inputs | tIN | 50 | ns | Any pulse narrower than the max spec is suppressed | 5 | ||
| SCL Falling Edge to SDA Output Data Valid | tAA | 900 | ns | SCL falling edge crossing 30% of VDD, until SDA exits the 30% to 70% of VDD window | 5 | ||
| Bus Free Time Before New Transmission | tBUF | 1300 | ns | SDA crossing 70% of VDD during a STOP condition, to SDA crossing 70% of VDD during the following START condition | 5 | ||
| Clock LOW Time | tLOW | 1300 | ns | Measured at the 30% of VDD crossing | 5 | ||
| Clock HIGH Time | tHIGH | 600 | ns | Measured at the 70% of VDD crossing | 5 | ||
| START Condition Setup Time | tSU:STA | 600 | ns | SCL rising edge to SDA falling edge. Both crossing 70% of VDD | 5 | ||
| START Condition Hold Time | tHD:STA | 600 | ns | From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD | 5 | ||
| Input Data Setup Time | tSU:DAT | 100 | ns | From SDA exiting the 30% to 70% of VDD window, to SCL rising edge crossing 30% of VDD | 5 | ||
| Input Data Hold Time | tHD:DAT | 0 | 900 | ns | From SCL falling edge crossing 30% of VDD to SDA entering the 30% to 70% of VDD window | 5 | |
| STOP Condition Setup Time | tSU:STO | 600 | ns | From SCL rising edge crossing 70% of VDD, to SDA rising edge crossing 30% of VDD | 5 | ||
| STOP Condition Hold Time | tHD:STO | 600 | ns | From SDA rising edge to SCL falling edge. Both crossing 70% of VDD | 5 | ||
| Output Data Hold Time | tDH | 0 | ns | From SCL falling edge crossing 30% of VDD, until SDA enters the 30% to 70% of VDD window | 5 | ||
| SDA and SCL Rise Time | tR | 300 | ns | From 30% to 70% of VDD; min is 20 + 0.1 x Cb | 5 | ||
| SDA and SCL Fall Time | tF | 300 | ns | From 70% to 30% of VDD; min is 20 + 0.1 x Cb | 5 | ||
| Capacitive Loading of SDA or SCL | Cb | 400 | pF | Total on-chip and off-chip | 5 | ||
| SDA and SCL Bus Pull-Up Resistor Off-Chip | Rpu | 1 | kΩ | Maximum is determined by tR and tF | 5 | ||
| Voltage on VDD Pin | VDD | -0.2 | 4 | V | respect to GND | 4 | |
| Voltage on IRQ/FOUT, SCL and SDA Pins | -0.2 | 6 | V | respect to GND | 4 | ||
| Voltage on X1 and X2 Pins | -0.2 | 4 | V | respect to GND | 4 | ||
| ESD Rating Human Body Model | 4 | kV | Per MIL-STD-883 Method 3014, printed >4kV | 4 | |||
| ESD Rating Machine Model | 350 | V | Printed >350V | 4 | |||
| Storage Temperature | -65 | 150 | °C | 4 | |||
| Operating Temperature Range | -40 | 85 | °C | ISL12058IBZ-T | 2 | ||
| Thermal Resistance 8 Lead SOIC | θJA | 120 | °C/W | Typical, mounted on high effective thermal conductivity test board in free air | 4 |
CAD (KiCad official)
- Symbol:
ISL12058IBZ-T - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8-150mil (KiCad packages3D, STEP)
- 3D model files:
isl12058ibz-t-etched.step/isl12058ibz-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);isl12058ibz-t.step/isl12058ibz-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Intersil(Renesas Electronics) datasheet (20 pp, sha256
2d8e7292ed81b98f, retrieved 2026-10-23, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).