Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MCP45HV51-503E

Microchip Tech · Pre-ordered MCUs · TSSOP-14

MCP45HV51-503E from Microchip Tech, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VL power_in Positive digital power supply input, ranging from 1.8V to 5.5V relative to DGND, with a decoupling capacitor on VL to DGND recommended.
2 SCL input I2C serial clock input; the device is an I2C slave so SCL is input-only with a Schmitt trigger.
3 A1 input I2C address bit 1 input that, together with A0, completes the device address and allows up to four devices on one bus.
4 SDA bidirectional I2C serial data pin, an open-drain N-channel driver with Schmitt-trigger input that lets the host read and write the Wiper and TCON registers.
5 A0 input I2C address bit 0 input whose value is latched at POR/BOR, completing the device address together with A1.
6 WLAT input Wiper latch enable; when Low the received I2C value is transferred to the Wiper register, and when High it is held in the I2C shift register buffer (SPBUF).
7 NC unconnected Pin not internally connected to the die; to reduce noise coupling, connect it to either DGND or VL.
8 SHDN input Shutdown input that forces the resistor network terminals into the hardware shutdown state.
9 DGND power_in Digital ground reference for the device logic and the VL supply.
10 V- power_in Analog negative potential supply; its potential must be lower than or equal to the DGND pin potential.
11 P0B passive Potentiometer 0 Terminal B; voltage must be between V- and V+, and it can carry both positive and negative current.
12 P0W passive Potentiometer 0 wiper terminal; voltage must be between V- and V+, and it can carry both positive and negative current.
13 P0A passive Potentiometer 0 Terminal A; voltage must be between V- and V+, and it can carry both positive and negative current.
14 V+ power_in Analog positive supply, which must be at a higher potential than V-; analog operation is specified from 10V to 36V relative to V-.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package TSSOP-14
Category Embedded Processors & Controllers
Pins 14

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Resistance tolerance (RAB) RAB -20 20 % Resistance (± 20%), -503 device 4
End-to-end resistance RAB 40 50 60 k -503 devices, V+/V- = 10V to 36V 4
RAB current IAB 0.9 mA -503 devices, 36V / RAB(MIN), V- = -18V, V+ = +18V 4
Wiper resistance RW 75 170 ohm IW = 1 mA V+ = +18V, V- = -18V, code = 00h, PxA = floating, PxB = V-. 6
Wiper resistance RW 145 200 ohm IW = 1 mA V+ = +5.0V, V- = -5.0V, code = 00h, PxA = floating, PxB = V-. (Note 2) 6
Terminal current (A, B, W) IT, IW 6.5 mA -503 devices IBW(W ≠ ZS) and IAW(W ≠ FS) 6
Terminal current at zero/full scale IT, IW 36 mA IBW(W = ZS), or IAW(W = FS) 6
Supply current, serial interface active IDDD 45 650 µA Serial Interface Active, Write all 0's to Volatile Wiper 0 (address 0h), VL = 5.5V, FSCL = 3.4 MHz, V- = DGND 5
Supply current, serial interface inactive IDDD 4 7 µA Serial Interface Inactive, VL = 5.5V, SCL = VIH, Wiper = 0, V- = DGND 5
Supply current, analog IDDA 5 µA Current V+ to V-, PxA = PxB = PxW, DGND = V- +(V+/2) 5
Digital positive supply voltage VL 2.7 5.5 V With respect to DGND (Note 4) 4
Digital positive supply voltage VL 1.8 5.5 V VL ≥ V- + 2.7V (Note 1, Note 4) 4
Analog positive supply voltage V+ 36 V With respect to V- (Note 4) 4
Delay after device exits reset state TBORD 10 20 µs VL > VBOR 5
Power supply sensitivity PSS 0.0015 0.0035 %/% 8-bit VL = 2.7V to 5.5V, V+ = 18V, V- = -18V, Code = 7Fh 14
RAB current into PxA/PxB/PxW pins (continuous, 50 k) -6.5 6.5 mA RAB = 50 k 3
Voltage on V+ with respect to DGND V+ -0.3 40 V Printed as DGND - 0.3V to 40.0V 3
ESD protection, Human Body Model -5 5 kV HBM 3
Maximum junction temperature TJ 150 °C 3
Package power dissipation, TSSOP-14 1000 mW TA = +50°C, TJ = +150°C 3
Ambient temperature with power applied TA -40 125 °C 3
Storage temperature TA -65 150 °C 3
Thermal resistance, 14L-TSSOP (ST) θJA 100 °C/W 21
Nominal resistance tempco RAB/T 50 ppm/°C TA = -40°C to +85°C 6
Nominal resistance tempco RAB/T 100 ppm/°C TA = -40°C to +125°C 6
Ratiometric tempco VBW/T 15 ppm/°C Code = Mid scale (7Fh or 3Fh) 6
Leakage current into A, W or B ITL 5 nA A = W = B = V- 6
Capacitance (PW) CW 120 pF Measured to V-, f = 1 MHz, Wiper code = Mid Scale 13
VW settling time (50 k) tS 2.5 µs VA = 10V, VB = 0V, ±1LSb error band, CL = 50 pF, Code = 00h -> FFh (7Fh); FFh (7Fh) -> 00h 10

CAD (KiCad official)

  • Symbol: MCP45HV51-503E
  • Footprint: Package_SO:TSSOP-14_4.4x5mm_P0.65mm
  • 3D model: TSSOP-14 (KiCad packages3D, STEP)
  • 3D model files: mcp45hv51-503e-etched.step / mcp45hv51-503e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp45hv51-503e.step / mcp45hv51-503e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (100 pp, sha256 ab854db7c83242c1, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF