3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLP8556SQX-E08
Texas Instruments · LED Drivers · WQFN-24-EP(4x4)
LP8556SQX-E08 from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | passive | Connection to the drain terminal of the integrated power MOSFET; SW, LED1 to LED6 and VBOOST are rated -0.3 V to 50 V absolute maximum. |
| 2 | SW | passive | Connection to the drain terminal of the integrated power MOSFET; SW, LED1 to LED6 and VBOOST are rated -0.3 V to 50 V absolute maximum. |
| 3 | GND_SW | power_in | Connection to the source terminal of the integrated power MOSFET. |
| 4 | GND_SW | power_in | Connection to the source terminal of the integrated power MOSFET. |
| 5 | SDA | bidirectional | I2C data input/output pin; SCL, SDA and PWM are rated -0.3 V to 6 V absolute maximum. |
| 6 | SCL | input | I2C clock input pin; SCL, SDA and PWM are rated -0.3 V to 6 V absolute maximum. |
| 7 | EN / VDDIO | power_in | Dual-purpose chip enable and power supply reference for the PWM, SDA and SCL inputs; drive it with a logic gate capable of sourcing at least 1 mA, with a recommended range of 1.62 V to 3.6 V. |
| 8 | NC | unconnected | No connect pin. |
| 9 | PWM | input | PWM dimming input; supply a 75-Hz to 25-kHz PWM signal, and connect to GND if unused. |
| 10 | GND | power_in | Ground pin. |
| 11 | GND | power_in | Ground pin. |
| 12 | LED1 | passive | LED driver current sink pin; may be left floating if unused. |
| 13 | LED2 | passive | LED driver current sink pin; may be left floating if unused. |
| 14 | LED3 | passive | LED driver current sink terminal; may be left floating if unused. |
| 15 | GND | power_in | Ground pin. |
| 16 | LED4 | passive | LED driver current sink pin; may be left floating if unused. |
| 17 | LED5 | passive | LED driver current sink pin; may be left floating if unused. |
| 18 | LED6 | passive | LED driver current sink pin; may be left floating if unused. |
| 19 | VLDO | power_out | Internal LDO output pin; connect capacitor CVLDO between this pin and the ground reference. |
| 20 | VBOOST | power_out | Boost converter output pin monitored by internal feedback and overvoltage protection; connect the output capacitor bank close to this pin, with recommended range 0 V to 48 V. |
| 21 | FSET | passive | Sets the boost and PWM dimming frequency through resistor RFSET to ground (see Table 5); may be left floating if PWM_FSET_EN = 0 and BOOST_FSET_EN = 0. |
| 22 | VDD | power_in | Device power supply pin, 2.7 V to 20 V, which is the input of the internal LDO regulator. |
| 23 | ISET | passive | LED current set resistor RISET connects from this pin to ground; may be left floating if ISET_EN = 0. |
| 24 | GND | power_in | Ground pin. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-24-EP(4x4) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VDD | VDD | 2.7 | 20 | V | 6 | ||
| EN / VDDIO supply voltage | EN / VDDIO | 1.62 | 3.6 | V | 6 | ||
| Voltage on LED1...LED6, SW, VBOOST | V | 0 | 48 | V | 6 | ||
| Junction temperature | TJ | -30 | 125 | °C | 6 | ||
| Ambient temperature | TA | -30 | 85 | °C | 6 | ||
| VDD absolute maximum voltage | VDD | -0.3 | 24 | V | 6 | ||
| Voltage on logic pins (SCL, SDA, PWM) | -0.3 | 6 | V | 6 | |||
| Voltage on analog pins (VLDO, EN / VDDIO) | -0.3 | 6 | V | 6 | |||
| Voltage on analog pins (FSET, ISET) | -0.3 | V | 6 | ||||
| Voltage on LED1...LED6, SW, VBOOST | V | -0.3 | 50 | V | 6 | ||
| Junction temperature (TJ-MAX) | TJ-MAX | 125 | °C | 6 | |||
| Maximum lead temperature (soldering) | 260 | °C | 6 | ||||
| Storage temperature | Tstg | -65 | 150 | °C | 6 | ||
| Standby supply current | IDD | 1.6 | µA | EN / VDDIO = 0 V, LDO disabled, -30°C ≤ TA ≤ 85°C | 7 | ||
| Normal mode supply current, LDO enabled, boost disabled | IDD | 0.9 | 1.5 | mA | LDO enabled, boost disabled | 7 | |
| Normal mode supply current, LDO enabled, boost enabled, no load | IDD | 2.2 | 3.65 | mA | LDO enabled, boost enabled, no load | 7 | |
| Internal oscillator frequency accuracy | fOSC | -4 | 4 | % | 7 | ||
| Internal oscillator frequency accuracy | fOSC | -7 | 7 | % | -30°C ≤ TA ≤ 85°C | 7 | |
| LDO output voltage | VLDO | 2.95 | 3.05 | 3.15 | V | VDD ≥ 3.1 V | 7 |
| Boost minimum output voltage | VBOOST_MIN | 16 | V | VBOOST_RANGE = 1 | 8 | ||
| Boost maximum output voltage | VBOOST_MAX | 32.7 | 34.5 | 36.6 | V | VBOOST_MAX = 101, VBOOST_RANGE = 1 | 8 |
| Maximum continuous output load current | ILOAD_MAX | 220 | mA | VIN = 3 V, VOUT = 18 V | 8 | ||
| Maximum continuous output load current | ILOAD_MAX | 160 | mA | VIN = 3 V, VOUT = 24 V | 8 | ||
| Maximum continuous output load current | ILOAD_MAX | 120 | mA | VIN = 3 V, VOUT = 30 V | 8 | ||
| SW pin current limit | ISW_LIM | 0.66 | 0.9 | 1.16 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 00 | 8 |
| SW pin current limit | ISW_LIM | 0.88 | 1.2 | 1.4 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 01 | 8 |
| SW pin current limit | ISW_LIM | 1.12 | 1.5 | 1.73 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 10 | 8 |
| SW pin current limit | ISW_LIM | 1.35 | 1.8 | 2.07 | A | IBOOST_LIM_2X = 0, IBOOST_LIM = 11 | 8 |
| Switch minimum pulse width | tPULSE | 50 | ns | No load | 8 | ||
| LED leakage current | ILED_LEAKAGE | 0.1 | 1 | µA | Outputs LED1...LED6, VOUT = 48 V | 9 | |
| Maximum sink current | ILED_MAX | 50 | mA | LED1...LED6 | 9 | ||
| LED current accuracy | ILED | -3 | 1 | 3 | % | Output current set to 23 mA | 9 |
| LED current accuracy | ILED | -4 | 1 | 4 | % | Output current set to 23 mA, -30°C ≤ TA ≤ 85°C | 9 |
| LED PWM output pulse duty cycle | PWMDUTY | 0.02 | 100 | % | 100 Hz < fPWM ≤ 200 Hz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.04 | 100 | % | 1 kHz < fPWM ≤ 2 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.1 | 100 | % | 2 kHz < fPWM ≤ 5 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.2 | 100 | % | 5 kHz < fPWM ≤ 10 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.4 | 100 | % | 10 kHz < fPWM ≤ 20 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.6 | 100 | % | 20 kHz < fPWM ≤ 30 kHz | 9 | |
| LED PWM output pulse duty cycle | PWMDUTY | 0.8 | 100 | % | 30 kHz < fPWM ≤ 39 kHz | 9 | |
| PWM frequency range | fPWM | 75 | 25000 | Hz | 9 | ||
| Minimum pulse ON time | tMIN_ON | 1 | µs | 9 | |||
| Minimum pulse OFF time | tMIN_OFF | 1 | µs | 9 | |||
| Input low level | VIL | 0.3 | × VDDIO | -30°C ≤ TA ≤ 85°C | 10 | ||
| Input high level | VIH | 0.7 | × VDDIO | -30°C ≤ TA ≤ 85°C | 10 | ||
| Input current | II | -1 | 1 | µA | VDDIO = 0 V or 3.6 V, VI = 0 V or 3.6 V, -30°C ≤ TA ≤ 85°C | 10 | |
| Output low level (SDA) | VOL | 0.3 | V | IOUT = 3 mA (pull-up current) | 10 | ||
| SCL clock frequency | fSCL | 400 | kHz | 10 | |||
| Hold time (repeated) START condition | 0.6 | µs | 10 | ||||
| Clock low time | 1.3 | µs | 10 | ||||
| Rise time of SDA and SCL | 300 | ns | 20 + 0.1Cb | 10 | |||
| Junction-to-ambient thermal resistance (RTW, WQFN 24 pins) | RθJA | 35 | °C/W | 7 | |||
| Junction-to-case (top) thermal resistance (RTW, WQFN 24 pins) | RθJC(top) | 32.2 | °C/W | 7 | |||
| Junction-to-board thermal resistance (RTW, WQFN 24 pins) | RθJB | 13.7 | °C/W | 7 | |||
| Junction-to-case (bottom) thermal resistance (RTW, WQFN 24 pins) | RθJC(bot) | 3.3 | °C/W | 7 | |||
| Switch ON resistance | RDS_ON | 0.19 | Ω | ISW = 0.5A | 8 | ||
| VIN undervoltage lockout threshold | VUVLO | 2.5 | V | UVLO_TH = 0, falling | 8 | ||
| VIN undervoltage lockout threshold | VUVLO | 5.2 | V | UVLO_TH = 1, falling | 8 |
CAD (KiCad official)
- Symbol:
LP8556SQX-E08 - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lp8556sqx-e08-etched.step/lp8556sqx-e08-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp8556sqx-e08.step/lp8556sqx-e08.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (65 pp, sha256
13ca3211bd8fa7b8, retrieved 2026-10-31, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).