component
TPS2394PWR
Public Made by Adomby adom
Texas Instruments Supervisor And Reset ICs, TSSOP-14. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTPS2394PWR
Texas Instruments · Supervisor And Reset ICs · TSSOP-14
TPS2394PWR from Texas Instruments, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RTN | power_in | Supply return and positive supply input for negative-voltage systems, connected directly to the input bus return node, with an absolute maximum range of -0.3 V to 100 V. |
| 2 | FLT | output | Open-drain, active-low fault indication, pulled to SOURCE, able to sink 10 mA in fault and withstand 80 V without leakage when not faulted. |
| 3 | UV | input | Under-voltage comparator input with a 1.4 V threshold referenced to SOURCE; the linear current amplifier is enabled when UV is more than 1.4 V above SOURCE, and it can also serve as an active-high logic enable. |
| 4 | OV | input | Over-voltage comparator input with a 1.4 V threshold referenced to SOURCE; the linear current amplifier is enabled when OV is less than 1.4 V above SOURCE, and it can also serve as an active-low logic enable. |
| 5 | FLTTIM | bidirectional | Fault timer pin, with an external capacitor from FLTTIM to SOURCE setting the fault timeout; the capacitor is charged to the 4-V fault threshold (3.75 V to 4.25 V) and then discharged at about 1% of the charge rate to set the retry duty cycle. |
| 6 | RAMP | bidirectional | Inrush slew-rate programming input, with an external capacitor from RAMP to SOURCE that sets the turn-on current slew rate; when fully charged RAMP can exceed SOURCE by 6 V, and the sense reference is clamped to 42 mV. |
| 7 | SOURCE | power_in | Connection to the negative input supply rail and the reference for the UV, OV, FLTTIM, RAMP, and FLT/PG thresholds; the recommended supply is -12 V to -80 V with -48 V nominal. |
| 8 | NC | unconnected | Not connected; leave floating. |
| 9 | NC | unconnected | Not connected; leave floating. |
| 10 | SENSE | input | Positive current sense input; an external low-value resistor between SENSE and SOURCE sets the current limit, with the linear current amplifier regulating SENSE to 42 mV and an overload threshold of 120 mV that bypasses the fault timer. |
| 11 | GAT | output | Gate drive for the external N-channel protection MOSFET, which is driven up to 14 V above SOURCE when fully enhanced and pulled low during faults, with a sink current of 30 mA min in fault. |
| 12 | PG | output | Open-drain, active-high power-good output that goes high when the pass MOSFET is fully enhanced and load current is below the current limit; it is pulled to SOURCE, can sink 10 mA, and withstands 80 V without leakage when power is not good. |
| 13 | NC | unconnected | Not connected; leave floating. |
| 14 | NC | unconnected | Not connected; leave floating. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSSOP-14 |
| Category | Power Management (PMIC) |
| Pins | 14 |
CAD (KiCad official)
- Symbol:
TPS2394PWR - Footprint:
Package_SO:TSSOP-14_4.4x5mm_P0.65mm - 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files:
tps2394pwr-etched.step/tps2394pwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps2394pwr.step/tps2394pwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (23 pp, sha256
6e464d424e04733d, retrieved 2026-10-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).