3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownPI6CG33402ZHIEX
Diodes Incorporated · Clock Generators / Frequency Synthesizers / PLL · TQFN-32-EP(5x5)
PI6CG33402ZHIEX from Diodes Incorporated, in a TQFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin for the device (GND is also listed on pins 15, 26 and 30). |
| 2 | XTAL_IN/CLK | input | Crystal input or CMOS reference input, with a 25MHz input frequency specified for the crystal or CMOS reference. |
| 3 | XTAL_OUT | output | Crystal output, used with a 25MHz fundamental crystal (CL=8pF recommended) connected between XTAL_IN/CLK and XTAL_OUT. |
| 4 | VDD_OSC | power_in | Power supply for oscillator circuitry, nominal 3.3V, with a 3.135V to 3.465V supply range. |
| 5 | VDD_REFOUT | power_in | Power supply for the buffered CMOS REFOUT output, nominal 3.3V, with a 3.135V to 3.465V supply range. |
| 6 | SADR/REFOUT | bidirectional | Latched at first application of PD# to select the SMBus address (0 = 1101000, 1 = 1101010) or LVCMOS REFOUT; has an internal pulldown. |
| 7 | GND_REF | power_in | Ground for REFOUT. |
| 8 | GND_DIG | power_in | Ground for digital circuitry. |
| 9 | VDD_DIG | power_in | Power supply for digital circuitry, nominal 3.3V, with a 3.135V to 3.465V supply range. |
| 10 | SCLK | input | SMBus clock input, CMOS and 3.3V tolerant. |
| 11 | SDATA | bidirectional | SMBus data line, CMOS and 3.3V tolerant; SMBus input high voltage limit is 3.6V. |
| 12 | OE0# | input | Active-low output enable for the Q0 pair (1 = disable outputs, 0 = enable outputs), with an internal pulldown. |
| 13 | Q0+ | output | HCSL differential true clock output at 100MHz with on-chip termination, default ZOUT of 85Ω, blocked until the PLL is locked. |
| 14 | Q0- | output | HCSL differential complementary clock output paired with Q0+ at 100MHz with on-chip termination. |
| 15 | GND | power_in | Ground pin for the device. |
| 16 | VDDO | power_in | Power supply for the differential outputs, nominal 3.3V, with a 3.135V to 3.465V supply range (VDDO is also on pin 25). |
| 17 | OE1# | input | Active-low output enable for the Q1 pair (1 = disable outputs, 0 = enable outputs), with an internal pulldown. |
| 18 | Q1+ | output | HCSL differential true clock output at 100MHz with on-chip termination, default ZOUT of 85Ω, blocked until the PLL is locked. |
| 19 | Q1- | output | HCSL differential complementary clock output paired with Q1+ at 100MHz with on-chip termination. |
| 20 | GNDA | power_in | Ground for analog circuitry. |
| 21 | VDDA | power_in | Power supply for analog circuitry, nominal 3.3V, with a 3.135V to 3.465V supply range. |
| 22 | Q2+ | output | HCSL differential true clock output at 100MHz with on-chip termination, default ZOUT of 85Ω, blocked until the PLL is locked. |
| 23 | Q2- | output | HCSL differential complementary clock output paired with Q2+ at 100MHz with on-chip termination. |
| 24 | OE2# | input | Active-low output enable for the Q2 pair (1 = disable outputs, 0 = enable outputs), with an internal pulldown. |
| 25 | VDDO | power_in | Power supply for the differential outputs, nominal 3.3V, with a 3.135V to 3.465V supply range. |
| 26 | GND | power_in | Ground pin for the device. |
| 27 | Q3+ | output | HCSL differential true clock output at 100MHz with on-chip termination, default ZOUT of 85Ω, blocked until the PLL is locked. |
| 28 | Q3- | output | HCSL differential complementary clock output paired with Q3+ at 100MHz with on-chip termination. |
| 29 | OE3# | input | Active-low output enable for the Q3 pair (1 = disable outputs, 0 = enable outputs), with an internal pulldown. |
| 30 | GND | power_in | Ground pin for the device. |
| 31 | PD# | input | Low enters Power Down Mode and a subsequent high exits it; a high assertion also samples the latched inputs and starts up on first high, with an internal pullup. |
| 32 | SS_SEL_TRI | input | Tri-level latched input selecting spread at power-up (1 = -0.5%, M = -0.25%, 0 = spread off), with an internal pulldown. |
| 33 | ePad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | TQFN-32-EP(5x5) |
| Category | Clock and Timing |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | -65 | 150 | °C | 5 | |||
| Supply Voltage to Ground Potential | VDDxx | -0.5 | 4.6 | V | 5 | ||
| Input Voltage | -0.5 | 4.6 | V | VDD+0.5V, not exceed 4.6V | 5 | ||
| SMBus Input High Voltage | 3.6 | V | 5 | ||||
| ESD Protection (HBM) | 2000 | V | 5 | ||||
| Max Junction Temperature | 125 | °C | 5 | ||||
| Power Supply Voltage | VDDO, VDDA, VDD_OSC, VDD_DIG, VDD_REFOUT | 3.135 | 3.3 | 3.465 | V | 5 | |
| Ambient Temperature | TA | -40 | 85 | °C | Industrial grade | 5 | |
| Analog Power Supply Current | IDDA | 22 | 25 | mA | All outputs active @ 100MHz | 5 | |
| Power Supply Current | IDD | 13 | 16 | mA | All VDD, except VDDA and VDDO, All outputs active @ 100MHz | 5 | |
| IO Power Supply Current | IDDO | 20 | 25 | mA | VDDO, All outputs active @ 100MHz | 5 | |
| Thermal Resistance Junction to Ambient | θJA | 44.7 | °C/W | Still air | 22 | ||
| Thermal Resistance Junction to Case | θJC | 21.7 | °C/W | 22 | |||
| Output Voltage High | VOH | 660 | 784 | 850 | mV | Statistical measurement on single-ended signal using oscilloscope math function | 9 |
| Output Voltage Low | VOL | -150 | 150 | mV | 9 | ||
| Output Voltage Maximum | VOMAX | 816 | 1150 | mV | Measurement on single-ended signal using absolute value | 9 | |
| Output Voltage Minimum | VOMIN | -300 | -42 | mV | 9 | ||
| Output Cross Voltage | VOC | 250 | 430 | 550 | mV | 9 | |
| VOC Magnitude Change | DVOC | 12 | 140 | mV | 9 | ||
| Slew Rate (fast setting) | tRF | 2.5 | 3.2 | 4 | V/ns | Scope averaging on fast setting | 9 |
| Slew Rate (slow setting) | tRF | 2.2 | 3 | 3.7 | V/ns | Scope averaging on slow setting | 9 |
| Slew Rate Matching | DtRF | 7 | 15 | % | Scope averaging on | 9 | |
| Duty Cycle (HCSL) | tDC | 45 | 50 | 55 | % | Measured differentially, PLL Mode | 9 |
| Output Skew | tSKEW | 20 | 50 | ps | Averaging on, VT = 50% | 9 | |
| Cycle-to-Cycle Jitter | tjc-c | 20 | 50 | ps | 9 | ||
| Integrated Phase Jitter (RMS) | tjPHASE | 20 | 30 | 86 | ps(p-p) | PCIe 1.0 | 10 |
| Integrated Phase Jitter (RMS) | tjPHASE | 0.08 | 0.1 | 3 | ps | PCIe 2.0 Low Band, 10kHz < f < 1.5MHz | 10 |
| Integrated Phase Jitter (RMS) | tjPHASE | 0.99 | 1.3 | 3.1 | ps | PCIe 2.0 High Band, 1.5MHz < f < Nyquist (50MHz) | 10 |
| Integrated Phase Jitter (RMS) | tjPHASE | 0.32 | 0.42 | 1 | ps | PCIe 3.0 Common Clock Architecture (PLL BW of 2-4 or 2-5MHz, CDR = 10MHz) | 10 |
| Integrated Phase Jitter (RMS) | tjPHASE | 0.16 | 0.21 | 0.7 | ps | PCIe 3.0 Separate Reference No Spread (PLL BW of 2-4 or 2-5MHz, CDR =10 MHz) | 10 |
| Integrated Phase Jitter (RMS) | tjPHASE | 0.32 | 0.4 | 0.5 | ps | PCIe 4.0 (PLL BW of 2-4 or 2-5MHz, CDR = 10MHz) | 10 |
| Integrated Phase Jitter (RMS) | tjPHASE | 0.02 | 0.05 | 0.15 | ps | PCIe 5.0 (PLL BW of 500k to 1.8MHz. CDR = 20MHz) | 10 |
| Integrated Phase Jitter (RMS), -0.25% Spread | tjPHSRISG2 | 0.6 | 0.92 | 2 | ps | PCIe 2.0, Separate Reference Independent Spread (PLL BW of 16MHz, CDR=5MHz) | 10 |
| Integrated Phase Jitter (RMS), -0.25% Spread | tjPHSRISG3 | 0.32 | 0.4 | 0.7 | ps | PCIe 3.0, Separate Reference Independent Spread (PLL BW of 2-4MHz or 2-5MHz, CDR=10MHz) | 10 |
| Integrated Phase Jitter (RMS), -0.5% Spread | tjPHSRISG2 | 0.8 | 1.1 | 2 | ps | PCIe 2.0, Separate Reference Independent Spread (PLL BW of 16MHz, CDR=5MHz) | 10 |
| Integrated Phase Jitter (RMS), -0.5% Spread | tjPHSRISG3 | 0.35 | 0.6 | 0.7 | ps | PCIe 3.0, Separate Reference Independent Spread (PLL BW of 2-4MHz or 2-5MHz, CDR=10MHz) | 10 |
| Input Low Voltage | VIL | -0.3 | V | Single-ended inputs, except SMBus | 7 | ||
| Input High Current | IIH | 5 | µA | Single-ended inputs, VIN = VDD | 7 | ||
| Input Low Current | IIL | -5 | µA | Single-ended inputs, VIN = 0V | 7 | ||
| Input High Current (with pullup/pulldown) | IIH | 50 | µA | Single-ended inputs with pullup/pulldown resistor, VIN = VDD | 7 | ||
| Input Low Current (with pullup/pulldown) | IIL | -50 | µA | Single-ended inputs with pullup/pulldown resistor, VIN = 0V | 7 | ||
| Input Capacitance | CIN | 1.5 | 5 | pF | 7 | ||
| Input Rise Time | tRIN | 5 | ns | Single-ended inputs | 8 | ||
| Input Fall Time | tFIN | 5 | ns | Single-ended inputs | 8 | ||
| Clock Stabilization | tSTAB | 0.75 | 1 | ms | From power up and after input clock stabilization or deassertion of PD# to first clock | 8 | |
| Output Enable Latency | tOELAT | 1 | 3 | clocks | Q start after OE# assertion; Q stop after OE# deassertion | 8 | |
| PD# Deassertion Latency | tPDLAT | 20 | 300 | µs | Differential outputs enable after PD# deassertion | 8 | |
| REFOUT Slew Rate (Byte 3 = 1F) | tSLEW | 0.9 | 1.4 | 2 | V/ns | Byte 3 = 1F, 20% to 80% of VDDREF | 8 |
| REFOUT Duty Cycle | tDC | 45 | 50 | 55 | % | VT = VDD/2V, driven by a Xtal | 8 |
| REFOUT Cycle-Cycle Jitter | tJITCC | 70 | 150 | ps | VT = VDD/2V, driven by a Xtal | 8 | |
| REFOUT Phase Jitter, RMS (SSC off) | tJITPH | 0.16 | 0.3 | ps | 12kHz to 5MHz, SSC off, driven by a Xtal | 8 | |
| REFOUT Phase Jitter, RMS (SSC on) | tJITPH | 0.9 | 1.5 | ps | 12kHz to 5MHz, SSC on, driven by a Xtal | 8 | |
| Noise Floor | tJITN | -149 | -135 | dBc/Hz | 1kHz offset, driven by a Xtal | 8 | |
| SMBus Nominal Bus Voltage | VDDSMB | 2.7 | 3.6 | V | 6 | ||
| SMBus Input High Voltage | VIHSMB | 2.1 | 3.6 | V | SMBus, VDDSMB = 3.3V | 6 | |
| SMBus Input Low Voltage | VILSMB | 0.8 | V | SMBus, VDDSMB = 3.3V | 6 | ||
| SMBus Output Low Voltage | VOLSMB | 0.4 | V | SMBus at ISMBSINK | 6 | ||
| SS Modulation Frequency | fMOD | 30 | 31.8 | 33 | kHz | Triangular modulation | 6 |
| Pin Inductance | LPIN | 7 | nH | 6 | |||
| Equivalent Series Resistance | ESR | 50 | W | ESR value is dependent upon frequency of oscillation | 6 |
CAD (KiCad official)
- Symbol:
PI6CG33402ZHIEX - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: TQFN-32-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
pi6cg33402zhiex-etched.step/pi6cg33402zhiex-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);pi6cg33402zhiex.step/pi6cg33402zhiex.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (24 pp, sha256
94af1f3519d31368, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).