3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownISO5852SQDWRQ1
Texas Instruments · Gate Drive ICs · SOIC-16-300mil
ISO5852SQDWRQ1 from Texas Instruments, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VEE2 | power_in | Output negative supply; connect to GND2 for unipolar supply application. |
| 2 | DESAT | input | Desaturation voltage input for IGBT collector-emitter overcurrent detection, referenced to GND2. |
| 3 | GND2 | power_in | Gate drive common; connect to IGBT emitter. |
| 4 | OUTH | output | Positive gate drive voltage output (2.5-A peak source). |
| 5 | VCC2 | power_in | Most positive output supply potential, 15 V to 30 V with respect to GND2. |
| 6 | OUTL | output | Negative gate drive voltage output (5-A peak sink). |
| 7 | CLAMP | output | Miller clamp output, used to sink Miller current from the IGBT gate when the gate is turned off in unipolar operation. |
| 8 | VEE2 | power_in | Output negative supply; connect to GND2 for unipolar supply application. |
| 9 | GND1 | power_in | Input ground. |
| 10 | IN+ | input | Non-inverting gate drive voltage control input, CMOS compatible with thresholds referenced to VCC1. |
| 11 | IN- | input | Inverting gate drive voltage control input, CMOS compatible with thresholds referenced to VCC1. |
| 12 | RDY | output | Power-good output, high when both input-side and output-side supplies are good; open-drain with internal 50-kΩ pullup. |
| 13 | FLT | output | Fault output, active low during DESAT condition; latched until reset through RST after RDY goes high. |
| 14 | RST | input | Reset input; apply a low pulse of at least 800 ns to reset the fault latch. |
| 15 | VCC1 | power_in | Positive input supply, 2.25 V to 5.5 V. |
| 16 | GND1 | power_in | Input ground. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOIC-16-300mil |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC1 supply-voltage input side | VCC1 | -0.3 | 6 | V | referenced to GND1 | 4 | |
| Positive supply-voltage output side (VCC2, GND2) | VCC2 | -0.3 | 35 | V | 4 | ||
| Negative supply-voltage output side (VEE2, GND2) | VEE2 | -17.5 | 0.3 | V | referenced to GND2 | 4 | |
| Total-supply output voltage (VCC2, VEE2) | V(SUP2) | -0.3 | 35 | V | 4 | ||
| Gate-driver high output current | I(OUTH) | 2.7 | A | Maximum pulse width = 10 μs, Maximum duty cycle = 0.2% | 4 | ||
| Gate-driver low output current | I(OUTL) | 5.5 | A | Maximum pulse width = 10 μs, Maximum duty cycle = 0.2% | 4 | ||
| Output current of FLT, RDY | I(LOP) | 10 | mA | 4 | |||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | TSTG | -65 | 150 | °C | 4 | ||
| Supply-voltage input side (VCC1, GND1) | VCC1 | 2.25 | 5.5 | V | 4 | ||
| Positive supply-voltage output side (VCC2, GND2) | VCC2 | 15 | 30 | V | 4 | ||
| Negative supply-voltage output side (VEE2, GND2) | V(EE2) | -15 | 0 | V | 4 | ||
| Total supply-voltage output side (VCC2, VEE2) | V(SUP2) | 15 | 30 | V | 4 | ||
| Pulse width at IN+, IN- for full output | tUI | 40 | ns | CLOAD = 1 nF | 4 | ||
| Pulse width at RST for resetting fault latch | tRST | 800 | ns | 4 | |||
| Ambient temperature | TA | -40 | 125 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 99.6 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 48.5 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 56.5 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ψJT | 29.2 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 56.5 | °C/W | 5 | |||
| Maximum power dissipation (both sides) | PD | 1255 | mW | VCC1 = 5.5 V, VCC2 = 30 V, TA = 25°C | 5 | ||
| Maximum input power dissipation | PID | 175 | mW | VCC1 = 5.5 V, VCC2 = 30 V, TA = 25°C | 5 | ||
| Maximum output power dissipation | POD | 1080 | mW | VCC1 = 5.5 V, VCC2 = 30 V, TA = 25°C | 5 | ||
| Input-supply quiescent current | IQ1 | 2.8 | 4.5 | mA | 8 | ||
| Output-supply quiescent current | IQ2 | 3.6 | 6 | mA | 8 | ||
| Low-level clamp current | I(CLP) | 1.6 | 2.5 | 3.3 | A | V(CLAMP) = VEE2 + 2.5 V | 8 |
| Clamp threshold voltage | V(CLTH) | 1.6 | 2.1 | 2.5 | V | 8 | |
| Blanking-capacitor charge current | I(CHG) | 0.42 | 0.5 | 0.58 | mA | V(DESAT), GND2 = 2 V | 8 |
| DESAT threshold voltage with respect to GND2 | V(DSTH) | 8.3 | 9 | 9.5 | V | 9 | |
| Output-signal rise time at OUTH | tr | 12 | 18 | 35 | ns | CLOAD = 1 nF | 9 |
| Output-signal fall time at OUTL | tf | 12 | 20 | 37 | ns | CLOAD = 1 nF | 9 |
| Propagation delay | tPLH, tPHL | 76 | 110 | ns | CLOAD = 1 nF | 9 | |
| Glitch filter on IN+, IN-, RST | tGF (IN,/RST) | 20 | 30 | 40 | ns | CLOAD = 1 nF | 9 |
| Leading-edge blanking time | tLEB | 310 | 400 | 480 | ns | See Figure 44 and Figure 45 | 9 |
| Common-mode transient immunity | CMTI | 100 | 120 | kV/μs | VCM = 1500 V, see Figure 47 | 9 |
CAD (KiCad official)
- Symbol:
ISO5852SQDWRQ1 - Footprint:
Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm - 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
- 3D model files:
iso5852sqdwrq1-etched.step/iso5852sqdwrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);iso5852sqdwrq1.step/iso5852sqdwrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
318e69c0fd223ff4, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).