Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

INA310A1IDGKR

TEXAS INSTRUMENTS · Global Sourcing Parts · VSSOP-8

INA310A1IDGKR from TEXAS INSTRUMENTS, in a VSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VS power_in Power supply pin; the operating supply range is 2.7 V to 20 V.
2 OUT output Amplifier output voltage; the output can swing from as low as 20 mV to as high as 200 mV below the supply voltage.
3 CMPIN input Comparator input, which accepts 0 V up to 5.5 V or the supply voltage if it is lower than 5.5 V, with the comparator tripping at the 0.6 V internal threshold.
4 GND power_in Ground reference pin for the device.
5 RESET input Active-low comparator reset pin: low selects transparent mode and high selects latch mode, and the pin accepts 0 V to the supply voltage with an internal 2 MΩ (typical) pull-down.
6 CMPOUT output Open-drain comparator output that latches high when RESET is high, and can be pulled up to a voltage range of 0 V to 20 V through a pullup resistor.
7 IN- input Shunt resistor negative sense input, with a common-mode input range of −4 V to 110 V; connect to the load side of the sense resistor for high-side applications and to the ground side for low-side applications.
8 IN+ input Shunt resistor positive sense input, with a common-mode input range of −4 V to 110 V; connect to the bus-voltage side of the sense resistor for high-side applications and to the load side for low-side applications.

Key specifications

Parameter Value
Manufacturer TEXAS INSTRUMENTS
Package VSSOP-8
Category Global Sourcing Parts
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Common-mode input range VCM -4 48 110 V 4
Operating supply voltage VS 2.7 5 20 V 4
Operating free-air temperature TA -40 125 °C 4
Common-mode input range VCM -4 110 V TA = -40°C to +125°C 5
Supply voltage range VS 2.7 20 V TA = -40°C to +125°C 6
Quiescent current IQ 1.6 2 mA 6
Quiescent current IQ 2.25 mA TA = -40°C to +125°C 6
Supply voltage VS -0.3 22 V 4
Analog inputs differential (VIN+), (VIN-) VIN+, VIN- -12 12 V Differential (VIN+), (VIN-) 4
Analog inputs with respect to GND VIN+, VIN- -20 120 V with respect to GND 4
Input current into any pin 5 mA 4
Operating temperature TA -55 150 °C 4
Junction temperature TJ -65 150 °C 4
Storage temperature Tstg -65 150 °C 4
Junction-to-ambient thermal resistance (DGK) RθJA 172.2 °C/W 4
Junction-to-case (top) thermal resistance (DGK) RθJC(top) 63.5 °C/W 4
Junction-to-board thermal resistance (DGK) RθJB 93.8 °C/W 4
Junction-to-top characterization parameter (DGK) ΨJT 9.8 °C/W 4
Junction-to-board characterization parameter (DGK) ΨJB 92.2 °C/W 4
Common-mode rejection ratio CMRR 140 160 dB INA310Ax, VIN+ = -4 V to 110 V, TA = -40°C to +125°C 5
Offset voltage, RTI (INA310A1) VOS -150 30 150 µV 5
Offset drift, RTI (INA310A1, A2, A3) dVOS/dT -0.5 0.05 0.5 µV/°C TA = -40°C to +125°C, INA310A1, INA310A2, INA310A3 5
Power-supply rejection ratio, RTI (INA310A1) PSRR -8 1 8 µV/V INA310A1, 2.7 V ≤ VS ≤ 20 V, TA = -40°C to +125°C 5
Input bias current IB 10 20 30 µA IB+, IB-, VSENSE = 0 mV 5
Gain error (INA310Ax) GERR -0.15 0.02 0.15 % INA310Ax, GND + 50 mV ≤ VOUT ≤ VS, 200 mV 5
Gain error drift (INA310Ax) GERR 1 10 ppm/°C INA310Ax, TA = -40°C to +125°C 5
Nonlinearity error NLERR -0.01 0.01 % GND + 50 mV ≤ VOUT ≤ VS, 200 mV 5
Maximum capacitive load 500 pF No sustained oscillation, no isolation resistor 5
Swing to GND (offset above GND) VSN 5 20 mV RLOAD = 10 kΩ to GND, TA = -40°C to +125°C, VSENSE = 0 mV 5
Alert threshold VTHRESHOLD 585 600 615 mV TA = 25°C 6
Alert threshold VTHRESHOLD 580 620 mV TA = -40°C to +125°C 6
Comparator hysteresis 8 mV TA = 25°C 6
Input bias current, CMPIN IBCMPIN -20 1 20 nA TA = 25°C, VCMPIN = 0.4 V to 1.2 V 6
Minimum RESET pulse width 100 200 ns TA = -40°C to +125°C 6

CAD (KiCad official)

  • Symbol: INA310A1IDGKR
  • Footprint: Package_SO:VSSOP-8_3x3mm_P0.65mm
  • 3D model: VSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: ina310a1idgkr-etched.step / ina310a1idgkr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ina310a1idgkr.step / ina310a1idgkr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TEXAS INSTRUMENTS datasheet (34 pp, sha256 3e33543dd9085674, retrieved 2026-11-11, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF