component
XL393
Public Made by Adomby adom
XINLUDA Comparators, SOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownXL393
XINLUDA · Comparators · SOP-8
XL393 from XINLUDA, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | 1OUT | output | Output of comparator 1, an open-drain (open-collector) NPN pull-down that can be wired-AND with other open-collector outputs and sinks at most 20 mA (absolute maximum). |
| 2 | 1IN- | input | Inverting input of comparator 1; it should not go more than 0.3 V below ground, and it is limited to VCC - 1.5 V at the upper end of the common-mode range. |
| 3 | 1IN+ | input | Non-inverting input of comparator 1; it can exceed VCC and either input can go to 30 V without damage, and it should not go more than 0.3 V below ground. |
| 4 | GND | power_in | Ground reference pin; all voltages are measured with respect to network ground. |
| 5 | 2IN+ | input | Non-inverting input of comparator 2; it can exceed VCC and either input can go to 30 V without damage, and it should not go more than 0.3 V below ground. |
| 6 | 2IN- | input | Inverting input of comparator 2; it should not go more than 0.3 V below ground, and it is limited to VCC - 1.5 V at the upper end of the common-mode range. |
| 7 | 2OUT | output | Output of comparator 2, an open-drain (open-collector) NPN pull-down that can be wired-AND with other open-collector outputs and sinks at most 20 mA (absolute maximum). |
| 8 | VCC | power_in | Single-supply pin; recommended supply range is 2 V to 30 V for non-V devices (XL393 is non-V), with 36 V absolute maximum. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XINLUDA |
| Package | SOP-8 |
| Category | Amplifiers/Comparators |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage range | VCC | 36 | V | 4 | |||
| Differential input voltage | VID | -36 | 36 | V | Differential voltages are at IN+ with respect to IN- | 4 | |
| Input pin voltage range | VIN | -0.3 | 36 | V | 4 | ||
| Output pin voltage range | VO | 36 | V | 4 | |||
| Output current | IO | 20 | mA | 4 | |||
| Operating virtual-junction temperature | Tj | 300 | ℃ | 4 | |||
| Storage temperature range | Tstg | -65 | 150 | ℃ | 4 | ||
| Electrostatic discharge, Human Body Model | VESD | 0 | 2000 | V | HBM, per ANSI/ESDA/JEDEC JS-001 | 4 | |
| Electrostatic discharge, Charged Device Model | VESD | 0 | 1000 | V | CDM, per JEDEC JESD22-C101 | 4 | |
| Supply voltage (non-V devices) | VCC | 2 | 30 | V | Non-V devices (XL393) | 4 | |
| Junction temperature | Tj | -40 | 125 | °C | 4 | ||
| Operating free-air temperature range (characterized) | 0 | 70 | °C | XL393 characterized range per description and ordering table | 1 | ||
| Input offset voltage (table 6.5) | VIO | 2 | 5 | mV | Vcc = 5 V to 30 V, Vic = VICR min, Vo = 1.4 V, 25°C | 5 | |
| Input offset voltage (table 6.5, full range) | VIO | 9 | mV | Vic = VICR min, Vo = 1.4 V, full range | 5 | ||
| Input offset current (table 6.5) | IIO | 5 | 50 | nA | Vo = 1.4 V, 25°C | 5 | |
| Input offset current (table 6.5, full range) | IIO | 250 | nA | Vo = 1.4 V, full range | 5 | ||
| Input bias current (table 6.5) | IIB | -25 | -250 | nA | Vo = 1.4 V, 25°C | 5 | |
| Input bias current (table 6.5, full range) | IIB | -400 | nA | Vo = 1.4 V, full range | 5 | ||
| Common-mode input-voltage range (table 6.5) | VICR | 0 | V | 25°C; upper limit printed as Vcc -1.5 V | 5 | ||
| Common-mode input-voltage range (table 6.5, full range) | VICR | 0 | V | Full range; upper limit printed as Vcc -2 V | 5 | ||
| Large-signal differential-voltage amplification (table 6.5) | AVD | 50 | 200 | V/mV | Vcc = 15 V, Vo = 1.4 V to 11.4 V, RL ≥ 15 kΩ to Vcc, 25°C | 5 | |
| High-level output current (table 6.5) | IOH | 0.1 | 50 | nA | VOH = 5 V, VID = 1 V, 25°C | 5 | |
| High-level output current (table 6.5, full range) | IOH | 1 | µA | VOH = 30 V, VID = 1 V, full range | 5 | ||
| Low-level output voltage (table 6.5) | VOL | 150 | 400 | mV | IOL = 4 mA, VID = -1 V, 25°C | 5 | |
| Low-level output voltage (table 6.5, full range) | VOL | 700 | mV | IOL = 4 mA, VID = -1 V, full range | 5 | ||
| Low-level output current (table 6.5) | IOL | 6 | mA | VOL = 1.5 V, VID = -1 V, 25°C | 5 | ||
| Supply current (table 6.5) | Icc | 0.8 | 1 | mA | RL = ∞, Vcc = 5 V, 25°C | 5 | |
| Supply current (table 6.5, full range) | Icc | 2.5 | mA | RL = ∞, Vcc = 30 V, full range | 5 | ||
| Input offset voltage (table 6.6) | VID | 1 | 2 | mV | Vcc = 5 V to MAX, Vo = 1.4 V, 25°C | 6 | |
| Input offset voltage (table 6.6, full range) | VID | 4 | mV | Vic = VICR min, full range | 6 | ||
| Input offset current (table 6.6) | IIO | 5 | 50 | nA | Vo = 1.4 V, 25°C | 6 | |
| Input offset current (table 6.6, full range) | IIO | 150 | nA | Vo = 1.4 V, full range | 6 | ||
| Input bias current (table 6.6) | IIB | -25 | -250 | nA | Vo = 1.4 V, 25°C | 6 | |
| Input bias current (table 6.6, full range) | IIB | -400 | nA | Vo = 1.4 V, full range | 6 | ||
| Common-mode input-voltage range (table 6.6) | VICR | 0 | V | 25°C; upper limit printed as Vcc -1.5 V | 6 | ||
| Common-mode input-voltage range (table 6.6, full range) | VICR | 0 | V | Full range; upper limit printed as Vcc -2 V | 6 | ||
| Large-signal differential-voltage amplification (table 6.6) | AVD | 50 | 200 | V/mV | Vcc = 15 V, Vo = 1.4 V to 11.4 V, RL ≥ 15 kΩ to Vcc, 25°C | 6 | |
| High-level output current (table 6.6) | IOH | 0.1 | 50 | nA | VOH = 5 V, VID = 1 V, 25°C | 6 | |
| High-level output current (table 6.6, full range) | IOH | 1 | µA | VOH = 30 V, VID = 1 V, full range | 6 | ||
| Low-level output voltage (table 6.6) | VOL | 150 | 400 | mV | IOL = 4 mA, VID = -1 V, 25°C | 6 | |
| Low-level output voltage (table 6.6, full range) | VOL | 700 | mV | IOL = 4 mA, VID = -1 V, full range | 6 | ||
| Low-level output current (table 6.6) | IOL | 6 | mA | VOL = 1.5 V, VID = -1 V, 25°C | 6 | ||
| Supply current (table 6.6) | Icc | 0.8 | 1 | mA | RL = ∞, Vcc = 5 V, 25°C | 6 | |
| Supply current (table 6.6, full range) | Icc | 2.5 | mA | RL = ∞, Vcc = 30 V, full range | 6 | ||
| Junction-to-ambient thermal resistance (SOP 8-pin) | RSJA | 97 | °c/w | SOP 8 pins | 4 |
CAD (KiCad official)
- Symbol:
XL393 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
xl393-etched.step/xl393-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xl393.step/xl393.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XINLUDA datasheet (16 pp, sha256
a26f77a27e4aad48, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).