3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMAX3221CAE+
Analog Devices Inc./Maxim Integrated · RS232 ICs · SSOP-16
MAX3221CAE+ from Analog Devices Inc./Maxim Integrated, in a SSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Receiver enable control: drive low for normal receiver operation, or high to force the receiver outputs into a high-impedance state. |
| 2 | C1+ | passive | Positive terminal of the voltage doubler charge-pump capacitor. |
| 3 | V+ | power_out | +5.5V generated by the charge pump, regardless of VCC over the +3.0V to +5.5V range. |
| 4 | C1- | passive | Negative terminal of the voltage doubler charge-pump capacitor. |
| 5 | C2+ | passive | Positive terminal of the inverting charge-pump capacitor. |
| 6 | C2- | passive | Negative terminal of the inverting charge-pump capacitor. |
| 7 | V- | power_out | -5.5V generated by the charge pump, regardless of VCC over the +3.0V to +5.5V range. |
| 8 | R1IN | input | RS-232 receiver input with an input voltage range of -25V to +25V. |
| 9 | R1OUT | output | TTL/CMOS receiver output; the receiver is an inverting three-state output. |
| 10 | INVALID | output | Output of the valid signal detector that goes high when a valid RS-232 level is present on the receiver inputs. |
| 11 | T1IN | input | TTL/CMOS transmitter input. |
| 12 | FORCEON | input | Drive high to override the automatic circuitry and keep the transmitters on (FORCEOFF must be high). |
| 13 | T1OUT | output | RS-232 transmitter output, with output voltage swing of at least ±5.0V when loaded with 3kΩ to ground. |
| 14 | GND | power_in | Ground reference for the device. |
| 15 | VCC | power_in | Supply voltage of +3.0V to +5.5V. |
| 16 | FORCEOFF | input | Drive low to shut down the transmitters and on-board power supply, overriding all automatic circuitry and FORCEON. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc./Maxim Integrated |
| Package | SSOP-16 |
| Category | Interface |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Current, AutoShutdown | 1 | 10 | µA | VCC = 3.3V or 5.0V, TA = +25°C; all R_IN open, FORCEON = GND, FORCEOFF = VCC | 2 | ||
| Supply Current, Shutdown | 1 | 10 | µA | FORCEOFF = GND | 2 | ||
| Supply Current, AutoShutdown Disabled | 0.3 | 1 | mA | FORCEON = FORCEOFF = VCC, no load | 2 | ||
| Input Logic Threshold Low | 0.8 | V | T_IN, FORCEON, FORCEOFF, EN (MAX3223) | 2 | |||
| Input Logic Threshold High | 2 | V | T_IN, EN, FORCEON, FORCEOFF; VCC = 3.3V | 2 | |||
| Input Logic Threshold High | 2.4 | V | T_IN, EN, FORCEON, FORCEOFF; VCC = 5.0V | 2 | |||
| Input Leakage Current | -1 | 0.01 | 1 | µA | T_IN, EN, FORCEON, FORCEOFF | 2 | |
| Output Leakage Current | -10 | 0.05 | 10 | µA | Receivers disabled | 2 | |
| Output Voltage Low | 0.4 | V | IOUT = 1.6mA | 2 | |||
| Receiver Input Threshold to Transmitters Enabled, Positive threshold | 2.7 | V | Figure 5 | 2 | |||
| Receiver Input Threshold to Transmitters Enabled, Negative threshold | -2.7 | V | Figure 5 | 2 | |||
| Receiver Input Threshold to Transmitters Disabled | -0.3 | 0.3 | V | 1µA supply current, Figure 5 | 2 | ||
| INVALID Output Voltage Low | 0.4 | V | IOUT = 1.6mA | 2 | |||
| Receiver Threshold to Transmitters Enabled | tWU | 250 | µs | Figure 5 | 2 | ||
| Receiver Positive or Negative Threshold to INVALID High | tINVH | 1 | µs | Figure 5 | 3 | ||
| Receiver Positive or Negative Threshold to INVALID Low | tINVL | 30 | µs | Figure 5 | 3 | ||
| Receiver Input Voltage Range | -25 | 25 | V | 3 | |||
| Input Threshold Low | 0.6 | 1.2 | V | TA = +25°C, VCC = 3.3V | 3 | ||
| Input Threshold Low | 0.8 | 1.5 | V | TA = +25°C, VCC = 5.0V | 3 | ||
| Input Threshold High | 1.5 | 2.4 | V | TA = +25°C, VCC = 3.3V | 3 | ||
| Input Threshold High | 1.8 | 2.4 | V | TA = +25°C, VCC = 5.0V | 3 | ||
| Input Resistance | 3 | 5 | 7 | kΩ | TA = +25°C | 3 | |
| Output Voltage Swing | -5 | 5.4 | V | All transmitter outputs loaded with 3kΩ to ground | 3 | ||
| Output Resistance | 300 | Ω | VCC = V+ = V- = 0V, transmitter output = ±2V | 3 | |||
| Output Resistance | 10 | MΩ | VCC = V+ = V- = 0V, transmitter output = ±2V | 3 | |||
| Output Short-Circuit Current | -35 | 60 | mA | 3 | |||
| Output Leakage Current | -25 | 25 | µA | VOUT = ±12V, VCC = 0V or 3.0V to 5.5V, transmitters disabled | 3 | ||
| Maximum Data Rate | 120 | 235 | kbps | RL = 3kΩ, CL = 1000pF, one transmitter switching | 3 | ||
| Transmitter Skew, MAX3221/MAX3223 | │tPHL, tPLH│ | 200 | ns | 3 | |||
| Receiver Skew, MAX3221/MAX3223 | │tPHL, tPLH│ | 100 | ns | 3 | |||
| Transition-Region Slew Rate | 4 | 8 | 30 | V/µs | VCC = 3.3V, RL = 3kΩ to 7kΩ, TA = +25°C, measured from +3V to -3V or -3V to +3V; CL = 200pF to 2500pF | 3 | |
| Transition-Region Slew Rate | 6 | 30 | V/µs | VCC = 3.3V, RL = 3kΩ to 7kΩ, TA = +25°C, measured from +3V to -3V or -3V to +3V; CL = 200pF to 1000pF | 3 | ||
| Receiver Output Enable Time | 200 | ns | Normal operation | 3 | |||
| Receiver Output Disable Time | 200 | ns | Normal operation | 3 | |||
| Supply Voltage VCC | VCC | 3 | 5.5 | V | Single supply operating range (Selector Guide, MAX3221) | 1 | |
| Supply Voltage VCC | VCC | -0.3 | 6 | V | 2 | ||
| Positive charge-pump output V+ | V+ | -0.3 | 7 | V | Note 1 | 2 | |
| Negative charge-pump output V- | V- | -7 | 0.3 | V | Note 1 | 2 | |
| V+ + /V-/ | 13 | V | Note 1 | 2 | |||
| Input Voltage, T_IN, FORCEOFF, FORCEON, EN | -0.3 | 6 | V | 2 | |||
| Input Voltage, R_IN | -25 | 25 | V | 2 | |||
| Output Voltage, T_OUT | -13.2 | 13.2 | V | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature | 300 | °C | Soldering, 10s | 2 | |||
| Operating Temperature Range, commercial (MAX32__C__) | 0 | 70 | °C | Commercial grade; applies to MAX3221CAE | 2 | ||
| Minimum capacitor C1 (Table 3) | C1 | 0.1 | µF | VCC = 3.0 to 5.5V; do not use values smaller than listed | 11 | ||
| Minimum capacitors C2, C3, C4 (Table 3) | C2, C3, C4 | 0.47 | µF | VCC = 3.0 to 5.5V; do not use values smaller than listed | 11 | ||
| Input Hysteresis | 0.3 | V | 3 | ||||
| Receiver Propagation Delay, tPHL | tPHL | 0.3 | µs | Receiver input to receiver output, CL = 150pF | 3 | ||
| Receiver Propagation Delay, tPLH | tPLH | 0.3 | µs | Receiver input to receiver output, CL = 150pF | 3 | ||
| Thermal Resistance, junction-to-ambient, single layer board | θJA | 140 | °C/W | 16 SSOP, single layer board | 15 | ||
| Thermal Resistance, junction-to-case, single layer board | θJC | 34 | °C/W | 16 SSOP, single layer board | 15 | ||
| Thermal Resistance, junction-to-ambient, multi layer board | θJA | 86 | °C/W | 16 SSOP, multi layer board | 15 | ||
| Thermal Resistance, junction-to-case, multi layer board | θJC | 33 | °C/W | 16 SSOP, multi layer board | 15 |
CAD (KiCad official)
- Symbol:
MAX3221CAE+ - Footprint:
Package_SO:SSOP-16_5.3x6.2mm_P0.65mm - 3D model: SSOP-16 (KiCad packages3D, STEP)
- 3D model files:
max3221cae-etched.step/max3221cae-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max3221cae.step/max3221cae.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices Inc./Maxim Integrated datasheet (16 pp, sha256
4b10ea08c7155060, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).