component
FT4222HQ-D-T
Public Made by Adomby adom
FTDI Interface - Specialized, VQFN-32(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownFT4222HQ-D-T
FTDI · Interface - Specialized · VQFN-32(5x5)
FT4222HQ-D-T from FTDI, in a VQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DEBUGGER | bidirectional | Debugging pin that should be reserved and tied high. |
| 2 | STEST_RSTN | input | Chip reset input for test mode, active low, which should be reserved and tied high. |
| 3 | RESETN | input | Chip reset input for non-test mode operation, active low; it can be tied to VCCIO (+3.3V) if not used. |
| 4 | DCNF0 | input | Chip mode configuration selection bit 0, which together with DCNF1 selects one of the four chip configuration modes. |
| 5 | DCNF1 | input | Chip mode configuration selection bit 1, which together with DCNF0 selects one of the four chip configuration modes. |
| 6 | DGND | power_in | Digital ground. |
| 7 | VCCIO | power_in | Supply for all I/O ports at +3.3V, +2.5V or +1.8V, and must be connected to pin 25 when the I/O ports operate at 3.3V. |
| 8 | SCK | bidirectional | SPI interface clock, serial clock output in SPI master mode and serial clock input in SPI slave mode. |
| 9 | MISO | bidirectional | SPI master single mode serial data input, SPI dual/quad mode data bus bit 1, or SPI slave mode serial data output. |
| 10 | MOSI | bidirectional | SPI master single mode serial data output, SPI dual/quad mode data bus bit 0, or SPI slave mode serial data input. |
| 11 | IO2 | bidirectional | Quad SPI data bus bit 2. |
| 12 | IO3 | bidirectional | Quad SPI data bus bit 3. |
| 13 | GPIO0/SS1O/SCL | bidirectional | GPIO 0 by default, configurable as SPI master slave select 1 output or as I2C serial clock (SCL). |
| 14 | GPIO1/SS2O/SDA | bidirectional | GPIO 1 by default, configurable as SPI master slave select 2 output or as I2C serial data (SDA). |
| 15 | GPIO2/SS3O/SUSP_OUT | bidirectional | GPIO 2 by default, configurable as SPI master slave select 3 output or as USB suspend output indicator. |
| 16 | GPIO3/WAKEUP/INTR | bidirectional | GPIO 3 by default, configurable as USB remote wakeup input or as interrupt input. |
| 17 | SS0O | output | Slave select 0 output in SPI master mode. |
| 18 | XSCI | input | Crystal oscillator input, 12 MHz only. |
| 19 | XSCO | output | Crystal oscillator output, 12 MHz only. |
| 20 | UGND | power_in | USB analog ground. |
| 21 | RREF | input | USB peripheral reference input that requires a 12 kOhm ±1% resistor connected to GND. |
| 22 | DM | bidirectional | USB peripheral bidirectional DM data line. |
| 23 | DP | bidirectional | USB peripheral bidirectional DP data line. |
| 24 | UGND | power_in | USB analog ground. |
| 25 | VOUT3V3 | power_out | Internal +3.3V regulator output that may power VCCIO and must be connected to pin 26; when VCCIN is supplied with 3.3V it becomes a power input. |
| 26 | VCCIN | power_in | Supply input of +5.0V (or 3.3V) to the embedded regulator. |
| 27 | AGND | power_in | Analog ground. |
| 28 | DGND | power_in | Digital ground. |
| 29 | VPP | power_in | +6.5V supply for programming the embedded OTP memory, which should be kept floating or at 0V when not programming. |
| 30 | VBUS_DET | input | VBUS detection input that is tolerant of +5.0V. |
| 31 | BCD_DET | output | Battery charger detection indicator output that is active when connected to a dedicated charger port, with polarity configurable. |
| 32 | SS | input | SPI slave select input from the SPI master, active in SPI slave mode and must be tied high when SPI master mode is enabled. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FTDI |
| Package | VQFN-32(5x5) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | -65 | 150 | °C | 23 | |||
| Ambient Operating Temperature (Power Applied) | -40 | 85 | °C | 23 | |||
| VCCIN Supply Voltage | -0.3 | 5.5 | V | 23 | |||
| VCCIO IO Voltage | -0.3 | 4 | V | 23 | |||
| VPP Supply Voltage | -0.25 | 6.5 | 0.25 | V | 23 | ||
| DC Input Voltage, USBDP and USBDM | -0.5 | 3.63 | V | 23 | |||
| DC Input Voltage, High Impedance Bi-directional (powered from VCCIO) | -0.3 | V | 23 | ||||
| DC Output Current, Outputs | 100 | mA | 23 | ||||
| VCCIN Operating Supply Voltage | VCC1 | 4.5 | 5 | 5.5 | V | VCCIN is supplied with 5V | 24 |
| VCCIN Operating Supply Voltage | VCC1 | 2.97 | 3.3 | 3.63 | V | VCCIN is supplied with 3.3V | 24 |
| VCCIO Operating Supply Voltage | VCC2 | 2.97 | 3.3 | 3.63 | V | VCCIO is supplied with 3.3V | 24 |
| VCCIO Operating Supply Voltage | VCC2 | 2.25 | 2.5 | 2.75 | V | VCCIO is supplied with 2.5V | 24 |
| VCCIO Operating Supply Voltage | VCC2 | 1.62 | 1.8 | 1.98 | V | VCCIO is supplied with 1.8V | 24 |
| Operating Supply Current | Icc1 | 50 | 52 | mA | Normal Operation at 24MHz | 24 | |
| Operating Supply Current | Icc1 | 62 | 64 | mA | Normal Operation at 48MHz | 24 | |
| Operating Supply Current | Icc1 | 68 | 70 | mA | Normal Operation at 60MHz | 24 | |
| Operating Supply Current | Icc1 | 78 | 80 | mA | Normal Operation at 80MHz | 24 | |
| Suspend Supply Current | Icc2 | 375 | 460 | μA | USB Suspend when SPI Master | 24 | |
| Suspend Supply Current | Icc2 | 377 | 465 | μA | USB Suspend when SPI Slave | 24 | |
| Suspend Supply Current | Icc2 | 386 | 419 | μA | USB Suspend when I2C Master | 24 | |
| Suspend Supply Current | Icc2 | 388 | 456 | μA | USB Suspend when I2C Slave | 24 | |
| 3.3v regulator output | 3V3 | 2.97 | 3.3 | 3.63 | V | VCCIN must be greater than 3V3 otherwise VOUT3V3 is an input which must be driven with 3.3V | 24 |
| Output Voltage High | Voh | 2.97 | V | Ioh = +/-2mA; I/O Drive strength* = 4mA | 25 | ||
| Output Voltage Low | Vol | 0 | 0.4 | V | Iol = +/-2mA; I/O Drive strength* = 4mA | 25 | |
| Input low Switching Threshold | Vil | 0.8 | V | LVTTL | 25 | ||
| Input High Switching Threshold | Vih | 2 | V | LVTTL | 25 | ||
| Input pull-up resistance | Rpu | 40 | 75 | 190 | KΩ | Vin = 0 | 25 |
| Input pull-down resistance | Rpd | 40 | 75 | 190 | KΩ | Vin =VCCIO | 25 |
| Input Leakage Current | Iin | -10 | 10 | μA | Vin = 0 | 25 | |
| Tri-state output leakage current | Ioz | -10 | 10 | μA | Vin = 5.5V or 0 | 25 | |
| Output Voltage High | Voh | 2.25 | V | Ioh = +/-2mA; I/O Drive strength* = 4mA | 26 | ||
| Output Voltage Low | Vol | 0 | 0.4 | V | Iol = +/-2mA; I/O Drive strength* = 4mA | 26 | |
| Input low Switching Threshold | Vil | 0.8 | V | LVTTL | 26 | ||
| Input High Switching Threshold | Vih | 1.7 | V | LVTTL | 26 | ||
| Input pull-up resistance | Rpu | 40 | 75 | 190 | KΩ | Vin = 0 | 26 |
| Input pull-down resistance | Rpd | 40 | 75 | 190 | KΩ | Vin =VCCIO | 26 |
| Input Leakage Current | Iin | -10 | 10 | μA | Vin = 0 | 26 | |
| Tri-state output leakage current | Ioz | -10 | 10 | μA | Vin = 5.5V or 0 | 26 | |
| Output Voltage High | Voh | 1.62 | V | Ioh = +/-2mA; I/O Drive strength* = 4mA | 27 | ||
| Output Voltage Low | Vol | 0 | 0.4 | V | Iol = +/-2mA; I/O Drive strength* = 4mA | 27 | |
| Input low Switching Threshold | Vil | 0.63 | V | LVTTL | 27 | ||
| Input High Switching Threshold | Vih | 1.17 | V | LVTTL | 27 | ||
| Input pull-up resistance | Rpu | 40 | 75 | 190 | KΩ | Vin = 0 | 27 |
| Input pull-down resistance | Rpd | 40 | 75 | 190 | KΩ | Vin =VCCIO | 27 |
| Input Leakage Current | Iin | -10 | 10 | μA | Vin = 0 | 27 | |
| Tri-state output leakage current | Ioz | -10 | 10 | μA | Vin = 5.5V or 0 | 27 | |
| PHY Operating Supply Voltage | VPHY, VPLL | 3 | 3.3 | 3.6 | V | 3.3V I/O | 28 |
| PHY Operating Supply Current | ICCPHY | 30 | 60 | mA | High-speed operation at 480 MHz | 28 | |
| PHY Suspend Supply Current | ICCPHY(susp) | 210 | 250 | μA | USB Suspend | 28 | |
| High Speed Differential input voltage sensitivity | VHSDIFF | 300 | mV | Measure at the connection of an application circuit | 28 | ||
| Full Speed Differential input voltage sensitivity | VDI | 0.2 | V | VI(DP), VI(DM) | 28 | ||
| Differential common mode voltage range of full speed data signalling | VCM | 0.8 | 2.5 | V | 28 | ||
| Full Speed Low-level output voltage | VOLPHY | 0 | 0.3 | V | 29 | ||
| Full Speed High-level output voltage | VOHPHY | 2.8 | 3.6 | V | 29 |
CAD (KiCad official)
- Symbol:
FT4222HQ-D-T - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: VQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
ft4222hq-d-t-etched.step/ft4222hq-d-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft4222hq-d-t.step/ft4222hq-d-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FTDI datasheet (47 pp, sha256
d109323d99285cfe, retrieved 2026-11-05, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).