component
ZGR1033AG1
Public Made by Adomby adom
Zynalog Voltage Reference, SOT-23-3. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownZGR1033AG1
Zynalog · Voltage Reference · SOT-23-3
ZGR1033AG1 from Zynalog, in a SOT-23-3. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input supply voltage: recommended range is Vout + Vdrop to 5.5 V (absolute maximum 6 V, from -0.3 V), and if Vout is below 2.5 V the input must be at least 2.5 V. |
| 2 | VOUT | power_out | Voltage reference output, rated for load currents of -10 mA to +10 mA with output voltage absolute maximum of 5.5 V and short-circuit current of 22 mA (maximum, absolute rating). |
| 3 | GND | power_in | Ground reference pin for the device. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Zynalog |
| Package | SOT-23-3 |
| Category | Power Management (PMIC) |
| Pins | 3 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 输入电源电压 (input supply voltage) | Vin | -0.3 | 6 | V | 4 | ||
| 使能引脚电压 (enable pin voltage) | VEN | -0.3 | V | printed max is Vin + 0.3 | 4 | ||
| 输出电压 (output voltage) | Vout | -0.3 | 5.5 | V | 4 | ||
| 输出短路电流 (output short-circuit current) | Isc | 22 | mA | 4 | |||
| 工作温度 (operating temperature, absolute max table) | TA | -55 | 160 | °C | 4 | ||
| 储存温度 (storage temperature) | Tstg | -65 | 170 | °C | 4 | ||
| 输入电压 (recommended input voltage) | Vin | 5.5 | V | min printed as Vout + Vdrop (footnote: at least 2.5 V if Vout < 2.5 V) | 4 | ||
| 使能电压 (recommended enable voltage) | VEN | 0 | V | max printed as Vin | 4 | ||
| 输出电流 (output current) | Iload | -10 | 10 | mA | 4 | ||
| 工作温度 (recommended operating temperature) | TA | -40 | 125 | °C | 4 | ||
| 初始精度 (initial output accuracy) | Vout | -0.2 | 0.2 | % | TA = 25°C | 5 | |
| 输出电压温漂 (output voltage temperature drift) | Vout | 30 | ppm/°C | −40°C ≤ TA ≤ 125°C | 5 | ||
| 线性调整率 (line regulation) | ΔVout/ΔVin | 4 | 20 | ppm/V | Vout + Vdrop ≤ Vin ≤ 5.5V | 5 | |
| 负载调整率 (load regulation, source) | ΔVout/ΔIload | 7.5 | 20 | ppm/mA | Iload = 0 to 10mA; Vin = Vout + Vdrop | 5 | |
| 负载调整率 (load regulation, sink) | ΔVout/ΔIload | 2 | 10 | ppm/mA | Iload = −10mA to 0; Vin = Vout + Vdrop | 5 | |
| 容性负载 (capacitive load) | Cload | 0.1 | 100 | µF | 5 | ||
| 静态电流 工作模式 (quiescent current, operating mode) | Iq | 330 | 350 | µA | 工作模式 | 5 | |
| 静态电流 关断输出模式 (quiescent current, shutdown output mode) | Iq | 1.5 | 5 | µA | 关断输出模式 | 5 | |
| 使能电压 高 (enable high threshold) | VEN | 2 | V | 工作模式 (EN=1) | 5 | ||
| 使能电压 低 (enable low threshold) | VEN | 0.3 | V | 关断输出模式 (EN=0) | 5 | ||
| 压降电压 (dropout voltage, 0 mA) | Vdrop | 8 | 50 | mV | Iload = 0mA | 5 | |
| 压降电压 (dropout voltage, 10 mA) | Vdrop | 310 | 500 | mV | Iload = 10mA | 5 | |
| 输出短路电流 (output short-circuit current) | Isc | 22 | 25 | mA | VOUT 接地 | 5 | |
| 使能启动时间 (enable startup time) | ton | 2.5 | mS | EN 使能启动; 0.1% settling, Cload = 10μF | 5 | ||
| 使能启动时间 (enable startup time) | ton | 240 | µS | EN 使能启动; 0.1% settling, Cload = 1μF | 5 | ||
| 上电启动时间 (power-up startup time) | ton | 250 | µS | 上电启动; 0.1% settling, Cload = 1μF; Vin = 3V | 5 | ||
| 上电启动时间 (power-up startup time) | ton | 200 | µS | 上电启动; 0.1% settling, Cload = 1μF; Vin = 5V | 5 | ||
| 低频噪声 (low-frequency noise) | en(p−p) | 15 | μVpp/V | f = 0.1Hz to 10Hz | 5 | ||
| 宽带噪声 (broadband noise) | en | 45 | μVrms | f = 10Hz to 10KHz | 5 | ||
| 结至环境热阻 (junction-to-ambient thermal resistance) | RΘJA | 185 | °C/W | 4 | |||
| 结至外壳（顶部）热阻 (junction-to-case top thermal resistance) | RΘJC(top) | 156 | °C/W | 4 | |||
| 结至电路板热阻 (junction-to-board thermal resistance) | RΘJB | 29.6 | °C/W | 4 | |||
| 结至顶部特征参数 (junction-to-top characterization parameter) | ψJT | 33.8 | °C/W | 4 | |||
| 结至电路板特征参数 (junction-to-board characterization parameter) | ψJB | 29.1 | °C/W | 4 |
CAD (KiCad official)
- Symbol:
ZGR1033AG1 - Footprint:
Package_TO_SOT_SMD:SOT-23-3 - 3D model: SOT-23-3 (KiCad packages3D, STEP)
- 3D model files:
zgr1033ag1-etched.step/zgr1033ag1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);zgr1033ag1.step/zgr1033ag1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Zynalog datasheet (13 pp, sha256
0a00b15e0877f76d, retrieved 2026-10-18, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).