3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLAN9253-V
MICROCHIP TECHNOLOGY / ATMEL · Global Sourcing Parts · QFN-64(9x9)
LAN9253-V from MICROCHIP TECHNOLOGY / ATMEL, in a QFN-64(9x9). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OSCI | input | External 25 MHz crystal input that can also be over-driven by a single-ended clock oscillator, in which case OSCO is left unconnected. |
| 2 | OSCO | output | External 25 MHz crystal output. |
| 3 | OSCVDD12 | power_in | Crystal +1.2 V power supply, supplied by the on-chip regulator unless configured for regulator off mode via the REG_EN pin. |
| 4 | OSCVSS | power_in | Crystal ground. |
| 5 | VDD33 | power_in | +3.3 V power supply for the internal regulators, which must be supplied even if the internal regulators are disabled. |
| 6 | VDDCR | power_in | +1.2 V digital core supply (regulator output pin) supplied by the on-chip regulator unless regulator off mode is set, with 1 µF and 470 pF decoupling capacitors in parallel to ground. |
| 7 | REG_EN | input | Regulator enable; when tied to 3.3 V the internal 1.2 V regulators are enabled. |
| 8 | CLK_25/CLK_25_EN/XTAL_MODE | bidirectional | 25 MHz clock output (O8) and multi-level strap input: below 0.8 V disables CLK_25 and selects the crystal amplifier, 1.5 V enables CLK_25 with the crystal amplifier, above 2.2 V enables CLK_25 with Schmitt trigger input on OSCI. |
| 9 | ERRLED/PME/100FD_B/LEDPOL4 | bidirectional | ERR LED open-drain/open-source output (OD12/OS12) or PME output, which also latches the 100FD_B and LEDPOL4 straps at reset. |
| 10 | WAIT_ACK/PME/LATCH0/EE_EMUL_SPI3 | bidirectional | Host bus wait/acknowledge output (VO8/VOD8, tri-state when not selected), PME or LATCH0 function, with the EE_EMUL_SPI3 strap (pull-down) selecting the Beckhoff SPI Data Out sample mode. |
| 11 | RST# | bidirectional | Active-low system reset input with internal pull-up that may be left unconnected, and also driven low as an output during POR or an EtherCAT reset command. |
| 12 | D2/AD2/SOF/SIO2/EE_EMUL_SPI0 | bidirectional | Host bus data/address-data bit 2, Start of Frame output, SPI/SQI SIO2, or EE_EMUL_SPI0 strap, depending on mode. |
| 13 | D1/AD1/EOF/SO/SIO1 | bidirectional | Host bus data/address-data bit 1, End of Frame output, SPI serial data output SO or SQI SIO1, depending on mode. |
| 14 | VDDIO | power_in | +1.8 V to +3.3 V variable I/O power. |
| 15 | D14/AD14/DIGIO8/GPI8/GPO8/MII_TXD3/TX_SHIFT1 | bidirectional | Host bus data/address-data bit 14, digital I/O, GPI/GPO 8 or MII transmit data 3 (VO8), which carries the TX_SHIFT1 strap for MII TX timing. |
| 16 | D13/AD13/DIGIO7/GPI7/GPO7/MII_TXD2/TX_SHIFT0 | bidirectional | Host bus data/address-data bit 13, digital I/O, GPI/GPO 7 or MII transmit data 2 (VO8), which carries the TX_SHIFT0 strap for MII TX timing. |
| 17 | D0/AD0/WD_STATE/SI/SIO0 | bidirectional | Host bus data/address-data bit 0, SyncManager watchdog state output (0 means expired), SPI serial data input SI or SQI SIO0, depending on mode. |
| 18 | SYNC1/LATCH1/PME | bidirectional | Distributed Clock SYNC1 output (VO8/VOD8/VOS8) or LATCH1 input, also mappable as the PME output, not driven until the EEPROM is loaded. |
| 19 | D9/AD9/LATCH_IN/SCK | bidirectional | Host bus data/address-data bit 9, external data latch input LATCH_IN, or SPI/SQI serial clock input SCK, depending on mode. |
| 20 | VDDIO | power_in | +1.8 V to +3.3 V variable I/O power. |
| 21 | D12/AD12/DIGIO6/GPI6/GPO6/MII_TXD1/100FD_B | bidirectional | Host bus data/address-data bit 12, digital I/O, GPI/GPO 6 or MII transmit data 1 (VO8), which carries the 100FD_B strap in 3-port mode. |
| 22 | D11/AD11/DIGIO5/GPI5/GPO5/MII_TXD0/100FD_A | bidirectional | Host bus data/address-data bit 11, digital I/O, GPI/GPO 5 or MII transmit data 0 (VO8), which carries the 100FD_A strap in 3-port mode. |
| 23 | D10/AD10/DIGIO4/GPI4/GPO4/MII_TXEN | bidirectional | Host bus data/address-data bit 10, digital I/O, GPI/GPO 4 or MII transmit data enable output to the external PHY. |
| 24 | VDDCR | power_in | +1.2 V digital core power supply, supplied by the on-chip regulator unless regulator off mode is set. |
| 25 | A1/ALELO/OE_EXT/MII_CLK25/EE_EMUL_SPI2 | bidirectional | Host bus address bit 1 or address latch enable low, Output Enable input OE_EXT (low clears output data), or free-running 25 MHz MII clock output, with EE_EMUL_SPI2 strap (pull-down) setting SCS# polarity. |
| 26 | A3/BE0/DIGIO11/GPI11/GPO11/MII_RXDV | bidirectional | Host bus address bit 3 or byte enable 0, digital I/O, GPI/GPO 11 or MII receive data valid input from the external PHY. |
| 27 | A4/BE1/DIGIO12/GPI12/GPO12/MII_RXD0 | bidirectional | Host bus address bit 4 or byte enable 1, digital I/O, GPI/GPO 12 or MII receive data bit 0 from the external PHY. |
| 28 | CS/DIGIO13/GPI13/GPO13/MII_RXD1 | bidirectional | Host bus chip select (normally active low), digital I/O, GPI/GPO 13 or MII receive data bit 1 from the external PHY. |
| 29 | A2/ALEHI/DIGIO10/GPI10/GPO10/LINKACTLED2/EE_EMUL_ALELO_POL/MII_LINKPOL/LEDPOL2 | bidirectional | Host bus address bit 2 or address latch enable high, digital I/O, GPI/GPO 10, or Link/Activity LED 2 output, with MII_LINKPOL, EE_EMUL_ALELO_POL and LEDPOL2 straps latched at reset. |
| 30 | WR/ENB/DIGIO14/GPI14/GPO14/MII_RXD2 | bidirectional | Host bus write strobe or data enable strobe (normally active low), digital I/O, GPI/GPO 14 or MII receive data bit 2. |
| 31 | RD/RD_WR/DIGIO15/GPI15/GPO15/MII_RXD3 | bidirectional | Host bus read strobe or read/write direction control, digital I/O, GPI/GPO 15 or MII receive data bit 3. |
| 32 | VDDIO | power_in | +1.8 V to +3.3 V variable I/O power. |
| 33 | A0/D15/AD15/DIGIO9/GPI9/GPO9/MII_RXER | bidirectional | Host bus address bit 0 shared with data bit 15 or address/data bit 15, digital I/O, GPI/GPO 9 or MII receive error input from the external PHY. |
| 34 | SYNC0/LATCH0/PME | bidirectional | Distributed Clock SYNC0 output (VO8/VOD8/VOS8) or LATCH0 input, also mappable as the PME output, not driven until the EEPROM is loaded. |
| 35 | D3/AD3/WD_TRIG/SIO3/EE_EMUL_SPI1 | bidirectional | Host bus data/address-data bit 3, SyncManager watchdog trigger output, or SQI SIO3, with EE_EMUL_SPI1 strap (pull-up) configuring the SPI mode. |
| 36 | D6/AD6/DIGIO0/GPI0/GPO0/MII_RXCLK | bidirectional | Host bus data/address-data bit 6, digital I/O, GPI/GPO 0 or MII receive clock input from the external PHY. |
| 37 | VDDIO | power_in | +1.8 V to +3.3 V variable I/O power. |
| 38 | VDDCR | power_in | +1.2 V digital core power supply, supplied by the on-chip regulator unless regulator off mode is set. |
| 39 | D7/AD7/DIGIO1/GPI1/GPO1/MII_MDC | bidirectional | Host bus data/address-data bit 7, digital I/O, GPI/GPO 1 or MII serial management clock output (VO8) to the external PHY. |
| 40 | D8/AD8/DIGIO2/GPI2/GPO2/MII_MDIO | bidirectional | Host bus data/address-data bit 8, digital I/O, GPI/GPO 2 or MII serial management data input/output, which requires an external pull-up. |
| 41 | TESTMODE | input | Test mode select that must be tied to VSS for proper operation. |
| 42 | EESDA/TMS/EE_EMUL1 | bidirectional | EEPROM I2C serial data input/open-drain output that must be pulled up externally at all times, also JTAG TMS and EE_EMUL1 strap. |
| 43 | EESCL/TCK/EE_EMUL2 | bidirectional | EEPROM I2C clock input/open-drain output that must be pulled up externally when an EEPROM is used, also JTAG TCK and EE_EMUL2 strap. |
| 44 | IRQ/LATCH1 | bidirectional | Interrupt request output (VO8/VOD8) with programmable polarity, source and buffer type, or LATCH1 input in Digital I/O mode. |
| 45 | RUNLED/STATE_RUNLED/E2PSIZE/EE_EMUL0/LEDPOL3 | bidirectional | RUN or STATE_RUN LED open-drain/open-source output (VOD12/VOS12), also latching the E2PSIZE, EE_EMUL0 and LEDPOL3 straps at reset. |
| 46 | LINKACTLED1/TDI/CHIP_MODE1/LEDPOL1 | bidirectional | Link/Activity LED 1 open-drain/open-source output, JTAG TDI input, with CHIP_MODE1 and LEDPOL1 straps latched at reset. |
| 47 | VDDIO | power_in | +1.8 V to +3.3 V variable I/O power. |
| 48 | LINKACTLED0/TDO/CHIP_MODE0/100FD_A/LEDPOL0 | bidirectional | Link/Activity LED 0 open-drain/open-source output or JTAG TDO output (VO12), with CHIP_MODE0, 100FD_A and LEDPOL0 straps latched at reset. |
| 49 | D4/AD4/DIGIO3/GPI3/GPO3/MII_LINK | bidirectional | Host bus data/address-data bit 4, digital I/O, GPI/GPO 3 or MII link status input indicating a 100 Mbit/s full-duplex link, with polarity set by MII_LINKPOL. |
| 50 | D5/AD5/OUTVALID/SCS# | bidirectional | Host bus data/address-data bit 5, OUTVALID output marking valid outputs, or active-low SPI/SQI slave chip select input SCS#. |
| 51 | VDD33TXRX1 | power_in | +3.3 V Port A analog power supply. |
| 52 | TXNA | bidirectional | Port A twisted pair transmit/receive negative channel 1 (AIO), swapped internally if Auto-MDIX detects a reversed connection. |
| 53 | TXPA | bidirectional | Port A twisted pair transmit/receive positive channel 1 (AIO), swapped internally if Auto-MDIX detects a reversed connection. |
| 54 | RXNA | bidirectional | Port A twisted pair transmit/receive negative channel 2 (AIO), swapped internally if Auto-MDIX detects a reversed connection. |
| 55 | RXPA | bidirectional | Port A twisted pair transmit/receive positive channel 2 (AIO), swapped internally if Auto-MDIX detects a reversed connection. |
| 56 | VDD12TX1 | power_in | Port A transmitter +1.2 V supply from VDDCR, which must be tied to VDD12TX2 for proper operation. |
| 57 | RBIAS | passive | Internal bias reference connected to an external 12.1 kOhm, 1% resistor to ground, with a nominal 1.2 V that dissipates approximately 1 mW. |
| 58 | VDD33BIAS | power_in | +3.3 V master bias power supply. |
| 59 | VDD12TX2 | power_in | Port B transmitter +1.2 V supply from VDDCR, which must be tied to VDD12TX1 for proper operation. |
| 60 | RXPB | bidirectional | Port B twisted pair transmit/receive positive channel 2 (AIO), swapped internally if Auto-MDIX detects a reversed connection. |
| 61 | RXNB | bidirectional | Port B twisted pair transmit/receive negative channel 2 (AIO), swapped internally if Auto-MDIX detects a reversed connection. |
| 62 | TXPB | bidirectional | Port B twisted pair transmit/receive positive channel 1 (AIO), swapped internally if Auto-MDIX detects a reversed connection. |
| 63 | TXNB | bidirectional | Port B twisted pair transmit/receive negative channel 1 (AIO), swapped internally if Auto-MDIX detects a reversed connection. |
| 64 | VDD33TXRX2 | power_in | +3.3 V Port B analog power supply. |
| 65 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MICROCHIP TECHNOLOGY / ATMEL |
| Package | QFN-64(9x9) |
| Category | Global Sourcing Parts |
| Pins | 65 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (VDD12TX1, VDD12TX2, OSCVDD12, VDDCR) | 0 | 1.5 | V | Note 1 | 381 | ||
| Supply Voltage (VDD33TXRX1, VDD33TXRX2, VDD33BIAS, VDD33, VDDIO) | 0 | 3.6 | V | Note 1 | 381 | ||
| Ethernet Magnetics Supply Voltage | -0.5 | 3.6 | V | 381 | |||
| Negative voltage on signal pins, with respect to ground | -0.5 | V | Note 3 | 381 | |||
| Positive voltage on OSCI, with respect to ground | 3.6 | V | 381 | ||||
| Storage Temperature | -55 | 150 | °C | 381 | |||
| Junction Temperature | 150 | °C | 381 | ||||
| Supply Voltage (VDD12TX1, VDD12TX2, OSCVDD12, VDDCR) | 1.14 | 1.26 | V | 381 | |||
| Analog Port Supply Voltage (VDD33TXRX1, VDD33TXRX2, VDD33BIAS, VDD33) | 3 | 3.6 | V | 381 | |||
| I/O Supply Voltage (VDDIO) | 1.62 | 3.6 | V | Note 1 | 381 | ||
| Ethernet Magnetics Supply Voltage | 2.25 | 3.6 | V | 381 | |||
| Ambient Operating Temperature in Still Air (commercial version) | TA | 0 | 70 | °C | Note 4: commercial version | 381 | |
| Ambient Operating Temperature in Still Air (industrial version) | TA | -40 | 85 | °C | Note 4: industrial version | 381 | |
| Ambient Operating Temperature in Still Air (extended industrial version) | TA | -40 | 105 | °C | Note 4: extended industrial version | 381 | |
| Overshoot and Undershoot | VOS | 5 | % | 388 | |||
| Jitter | 1.4 | ns | Note 25 | 388 | |||
| Peak Differential Output Voltage High | VPPH | 950 | 1050 | mVpk | Note 23 | 388 | |
| Signal Amplitude Symmetry | VSS | 98 | 102 | % | Note 23 | 388 | |
| Signal Rise and Fall Time | TRF | 3 | 5 | ns | Note 23 | 388 | |
| Rise and Fall Symmetry | TRFS | 0.5 | ns | Note 23 | 388 | ||
| Duty Cycle Distortion | DCD | 35 | 50 | 65 | % | Note 24 | 388 |
| Transmitter Peak Differential Output Voltage | VOUT | 2.2 | 2.5 | 2.8 | V | Note 26 | 388 |
| Receiver Differential Squelch Threshold | VDS | 300 | 420 | 585 | mV | 388 | |
| Crystal Frequency | Ffund | 25 | MHz | Fundamental mode | 394 | ||
| 802.3 Frequency Tolerance at 25oC | Ftol | -40 | 40 | ppm | Note 28 | 394 | |
| 802.3 Frequency Stability Over Temp | Ftemp | -40 | 40 | ppm | Note 28 | 394 | |
| EtherCAT Frequency Tolerance at 25oC | Ftol | -15 | 15 | ppm | Note 31 | 394 | |
| EtherCAT Frequency Stability Over Temp | Ftemp | -15 | 15 | ppm | Note 31 | 394 | |
| Shunt Capacitance | CO | 7 | pF | 394 | |||
| Load Capacitance | CL | 18 | pF | 394 | |||
| Drive Level | PW | 300 | µW | Note 33 | 394 | ||
| Equivalent Series Resistance | R1 | 100 | Ω | 394 | |||
| Crystal operation output duty cycle | 44 | 57 | % | Note 37 | 395 | ||
| Junction to Ambient thermal resistance, still air | JA | 25.6 | °C/W | Measured in still air | 382 | ||
| Junction to Ambient thermal resistance, airflow 1 m/s | JA | 22.3 | °C/W | Airflow 1 m/s | 382 | ||
| Junction to Ambient thermal resistance, airflow 2.5 m/s | JA | 20 | °C/W | Airflow 2.5 m/s | 382 | ||
| Junction to Bottom of Case thermal resistance | JT | 0.2 | °C/W | Measured in still air | 382 | ||
| Junction to Top of Case thermal resistance | JC | 2.6 | °C/W | 382 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | abs | slicer error 100BASE-TX is +/-32. A higher absolute slicer error means a degraded signal receiving condition. | 200 | |
| contacts | copper | The ERRLED pin on the LAN9252 functioned as the fiber mode signal detect as well as the Port A FX-SD Enable. For copper twisted pair operation, this pin would either be tied to or pulled down to groun | 275 |
CAD (KiCad official)
- Symbol:
LAN9253-V - Footprint:
Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP6x6mm - 3D model: QFN-64(9x9) (KiCad packages3D, STEP)
- 3D model files:
lan9253-v-etched.step/lan9253-v-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lan9253-v.step/lan9253-v.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MICROCHIP TECHNOLOGY / ATMEL datasheet (402 pp, sha256
2e11a3736937eb96, retrieved 2026-11-07, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).