component
AD8027ARTZ-REEL7
Public Made by Adomby adom
Analog Devices Operational Amplifier, SOT-23-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownAD8027ARTZ-REEL7
Analog Devices · Operational Amplifier · SOT-23-6
AD8027ARTZ-REEL7 from Analog Devices, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | output | Amplifier output, which swings close to the supply rails and must not be shorted to ground or made to sink excessive current, as this can cause severe failure (short-circuit current is 120 mA at ±5 V per Table 1). |
| 2 | -VS | power_in | Negative supply pin; the total supply range is 2.7 V to 12 V, with an absolute maximum supply of 12.6 V. |
| 3 | +IN | input | Non-inverting input whose common-mode range extends 200 mV beyond the supply rails without phase reversal, and whose input current must be limited to below 10 mA by a series resistor when overdriven. |
| 4 | -IN | input | Inverting input with about 2 pF input capacitance, so the source impedance should generally be kept below 500 Ω unless the feedback network includes capacitance, and it should be balanced against the +IN impedance. |
| 5 | DISABLE/SELECT | input | Three-level control that selects the input crossover point (open or tri-state selects PNP-dominant operation, high selects NPN-dominant) and, when pulled low (−5 V to −4.2 V for ±5 V supplies, 0 V to 0.8 V for +5 V or +3 V supplies), disables the amplifier. |
| 6 | +VS | power_in | Positive supply pin; the total supply range is 2.7 V to 12 V, with an absolute maximum supply of 12.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SOT-23-6 |
| Category | Amplifiers/Comparators |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 工作范围 (supply voltage operating range) | 2.7 | 12 | V | 3 | |||
| 输入共模电压范围 (input common-mode voltage range) | -5.2 | 5.2 | V | 3 | |||
| −3 dB带宽 (−3 dB bandwidth) | 138 | 190 | MHz | G = 1, VO = 0.2 V p-p | 3 | ||
| −3 dB带宽 (−3 dB bandwidth) | 20 | 32 | MHz | G = 1, VO = 2 V p-p | 3 | ||
| 开环增益 (open-loop gain) | 100 | 110 | dB | VO = ±2.5 V | 3 | ||
| 共模抑制比 (CMRR) | 90 | 110 | dB | VCM = ±2.5 V | 3 | ||
| 电源抑制比 (PSRR) | 90 | 110 | dB | VS ± 1 V | 3 | ||
| 输入失调电压 (input offset voltage) | 200 | 800 | µV | SELECT = 三态或开路，PNP有效 | 3 | ||
| 输入失调电压 (input offset voltage) | 240 | 900 | µV | SELECT = 高电平NPN有效 | 3 | ||
| 输入偏置电流 (input bias current) | 4 | 6 | µA | VCM = 0 V，NPN有效 | 3 | ||
| 输入偏置电流 (input bias current) | -8 | -11 | µA | VCM = 0 V，PNP有效 | 3 | ||
| 输入失调电流 (input offset current) | 0.1 | 0.9 | µA | 3 | |||
| 交越低电平，选择输入电压 (crossover low-level select input voltage) | -3.3 | 5 | V | 三态 < ±20 μA | 3 | ||
| 交越高电平，选择输入电压 (crossover high-level select input voltage) | -3.9 | -3.3 | V | 3 | |||
| 禁用输入电压 (disable input voltage) | -5 | -3.9 | V | 3 | |||
| 每个放大器的静态电流 (quiescent current per amplifier) | 6.5 | 8.5 | mA | 3 | |||
| 静态电流（禁用） (quiescent current, disabled) | 370 | 500 | µA | SELECT = 低电平 | 3 | ||
| 电源电压 (supply voltage) | 12.6 | V | 6 | ||||
| 差分输入电压 (differential input voltage) | -1.8 | 1.8 | V | 6 | |||
| 存储温度 (storage temperature) | -65 | 125 | °C | 6 | |||
| 工作温度范围 (operating temperature range) | -40 | 125 | °C | 6 | |||
| 引脚温度范围 (lead temperature range) | 300 | °C | 焊接，10秒 | 6 | |||
| 结温 (junction temperature) | 150 | °C | 6 | ||||
| 结到环境热阻 (junction-to-ambient thermal resistance) | θJA | 170 | °C/W | SOT-23-6, JEDEC标准4层板 | 7 |
CAD (KiCad official)
- Symbol:
AD8027ARTZ-REEL7 - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
ad8027artz-reel7-etched.step/ad8027artz-reel7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ad8027artz-reel7.step/ad8027artz-reel7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
a67b8d8b72eebb3d, retrieved 2026-10-19, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).