Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

FT24C128A-TSR-B

FMD(Fremont Micro Devices) · EEPROM · SOP-8

FT24C128A-TSR-B from FMD(Fremont Micro Devices), in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 A0 input Device address input that is hardwired to VIH or VIL to match the device address bit, and is internally recognized as VIL if left unconnected.
2 A1 input Device address input that is hardwired to VIH or VIL to match the device address bit, and is internally recognized as VIL if left unconnected.
3 A2 input Device address input that is hardwired to VIH or VIL to match the device address bit, and is internally recognized as VIL if left unconnected.
4 GND power_in Ground reference for the device; input voltage on any pin is rated -0.3V to VCC + 0.3V relative to ground.
5 SDA bidirectional Bi-directional serial data line with an open-drain output that can be wired-OR with other open-drain devices and is typically pulled high by an external resistor.
6 SCL input Serial clock input where the rising edge latches data into the EEPROM and the falling edge clocks data out, supporting up to 1 MHz at 2.5-5.5V and 400 kHz at 1.8V.
7 WP input Write protect input that disables all programming when connected to VIH or VCC and allows programming when left unconnected or at VIL, without affecting read operations.
8 VCC power_in Power supply pin with an operating range of 1.8V to 5.5V and a decoupling capacitor of at least 10nF recommended.

Key specifications

Parameter Value
Manufacturer FMD(Fremont Micro Devices)
Package SOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC1 1.8 5.5 V 10
Supply read current ICC1 0.4 1 mA VCC @ 5.5V SCL = 100 kHz 10
Supply write current ICC2 2 3 mA VCC @ 5.5V SCL = 100 kHz 10
Standby supply current ISB1 1 µA VCC @ 1.8V, VIN = VCC or VSS 10
Input leakage current IIL 3 µA VIN = VCC or VSS 10
Output leakage current ILO 3 µA VIN = VCC or VSS 10
Input low level VIL -0.6 0.3 V max printed as VCC×0.3 10
Input high level VIH 0.7 0.5 V min printed as VCC×0.7, max printed as VCC + 0.5 10
Output low level VOL1 0.4 V VCC @ 1.8V, IOL = 0.15 mA 10
Clock frequency, SCL fSCL 400 kHz 1.8V 9
Clock frequency, SCL fSCL 1000 kHz 2.5-5.5V 9
Clock pulse width low tLOW 1.3 µs 1.8V 9
Clock pulse width low tLOW 0.4 µs 2.5-5.5V 9
Clock pulse width high tHIGH 0.6 µs 1.8V 9
Clock pulse width high tHIGH 0.4 µs 2.5-5.5V 9
Noise suppression time tI 100 ns 1.8V 9
Noise suppression time tI 50 ns 2.5-5.5V 9
Clock low to data out valid tAA 0.9 µs 1.8V 9
Clock low to data out valid tAA 0.55 µs 2.5-5.5V 9
Bus free time before new transmission tBUF 1.3 µs 1.8V 9
Bus free time before new transmission tBUF 0.5 µs 2.5-5.5V 9
START hold time tHD.STA 0.6 µs 1.8V 9
START hold time tHD.STA 0.25 µs 2.5-5.5V 9
START set-up time tSU.STA 0.6 µs 1.8V 9
START set-up time tSU.STA 0.25 µs 2.5-5.5V 9
Data in hold time tHD.DAT 0 µs 1.8V and 2.5-5.5V 9
Data in set-up time tSU.DAT 100 ns 1.8V and 2.5-5.5V 9
Input rise time tR 0.3 µs 1.8V and 2.5-5.5V 9
Input fall time tF 300 ns 1.8V 9
Input fall time tF 100 ns 2.5-5.5V 9
STOP set-up time tSU.STO 0.6 µs 1.8V 9
STOP set-up time tSU.STO 0.25 µs 2.5-5.5V 9
Data out hold time tDH 50 ns 1.8V and 2.5-5.5V 9
Vcc slew rate at power up tPWR,R 0.1 50 V/ms 1.8V and 2.5-5.5V 9
Time required after VCC stable before commands tPUP 100 µs 1.8V and 2.5-5.5V 9
Minimum time at Vcc=0V between power cycles tPOFF 500 ms 1.8V and 2.5-5.5V 9
Write cycle time tWR 5 ms 1.8V and 2.5-5.5V 9
Operating temperature -40 85 ℃ Industrial operating temperature 2
Storage temperature -50 125 ℃ 2
Input voltage on any pin relative to ground -0.3 0.3 V max printed as VCC + 0.3V 2
Maximum voltage 8 V 2
ESD protection on all pins 4000 V >4000V 2
Supply voltage VCC 1.8 5.5 V 1

CAD (KiCad official)

  • Symbol: FT24C128A-TSR-B
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8 (KiCad packages3D, STEP)
  • 3D model files: ft24c128a-tsr-b-etched.step / ft24c128a-tsr-b-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ft24c128a-tsr-b.step / ft24c128a-tsr-b.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: FMD(Fremont Micro Devices) datasheet (17 pp, sha256 1e278f10b22d7c70, retrieved 2026-10-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF