3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSTM32F423CHU6
STMicroelectronics · ST Microelectronics · UFQFPN-48(7x7)
STM32F423CHU6 from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup battery supply pin for the RTC and backup domain (Table 10 lists VBAT as supply pin, additional function VBAT). |
| 2 | PC13-ANTI_TAMP | bidirectional | 5 V tolerant I/O supplied through the power switch (3 mA sink limit), output speed limited to 2 MHz with 30 pF max load and not usable as current source; additional function TAMP_1. |
| 3 | PC14-OSC32_IN | bidirectional | 5 V tolerant I/O (except in oscillator mode) supplied through the power switch, limited to 2 MHz/30 pF in output mode; additional function OSC32_IN for the 32 kHz crystal. |
| 4 | PC15-OSC32_OUT | bidirectional | 5 V tolerant I/O (except in oscillator mode) supplied through the power switch, limited to 2 MHz/30 pF in output mode; additional function OSC32_OUT for the 32 kHz crystal. |
| 5 | PH0-OSC_IN | bidirectional | I/O (5 V tolerant except in oscillator mode) with additional function OSC_IN for the 4-26 MHz crystal oscillator. |
| 6 | PH1-OSC_OUT | bidirectional | I/O (5 V tolerant except in oscillator mode) with additional function OSC_OUT for the 4-26 MHz crystal oscillator. |
| 7 | NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor. |
| 8 | VSSA/VREF- | power_in | Analog ground, shared with the ADC/DAC negative reference (VSSA). |
| 9 | VDDA/VREF+ | power_in | Analog supply, shared with the ADC/DAC positive reference (VDDA/VREF+). |
| 10 | PA0 | bidirectional | 5 V tolerant I/O with TIM2_CH1/ETR, TIM5_CH1, TIM8_ETR, USART2_CTS, UART4_TX alternate functions; additional functions ADC1_IN0, WKUP1. |
| 11 | PA1 | bidirectional | 5 V tolerant I/O with TIM2_CH2, TIM5_CH2, SPI4_MOSI, USART2_RTS, UART4_RX, QUADSPI_BK1_IO3 alternate functions; additional function ADC1_IN1. |
| 12 | PA2 | bidirectional | 5 V tolerant I/O with TIM2_CH3, TIM5_CH3, TIM9_CH1, I2S2_CKIN, USART2_TX, FSMC_D4 alternate functions; additional function ADC1_IN2. |
| 13 | PA3 | bidirectional | 5 V tolerant I/O with TIM2_CH4, TIM5_CH4, TIM9_CH2, I2S2_MCK, USART2_RX, SAI1_SD_B, FSMC_D5 alternate functions; additional function ADC1_IN3. |
| 14 | PA4 | bidirectional | 3.3 V tolerant I/O directly connected to DAC (TTa) with SPI1_NSS/I2S1_WS, SPI3_NSS/I2S3_WS, USART2_CK, DFSDM1_DATIN1, FSMC_D6 alternate functions; additional functions ADC1_IN4, DAC_OUT1. |
| 15 | PA5 | bidirectional | 3.3 V tolerant I/O directly connected to DAC (TTa) with TIM2_CH1/ETR, TIM8_CH1N, SPI1_SCK/I2S1_CK, DFSDM1_CKIN1, FSMC_D7 alternate functions; additional functions ADC1_IN5, DAC_OUT2. |
| 16 | PA6 | bidirectional | 5 V tolerant I/O with TIM1_BKIN, TIM3_CH1, TIM8_BKIN, SPI1_MISO, I2S2_MCK, DFSDM2_CKIN1, TIM13_CH1, QUADSPI_BK2_IO0, SDIO_CMD alternate functions; additional function ADC1_IN6. |
| 17 | PA7 | bidirectional | 5 V tolerant I/O with TIM1_CH1N, TIM3_CH2, TIM8_CH1N, SPI1_MOSI/I2S1_SD, DFSDM2_DATIN1, TIM14_CH1, QUADSPI_BK2_IO1 alternate functions; additional function ADC1_IN7. |
| 18 | PB0 | bidirectional | 5 V tolerant I/O with TIM1_CH2N, TIM3_CH3, TIM8_CH2N, SPI5_SCK/I2S5_CK alternate functions; additional function ADC1_IN8. |
| 19 | PB1 | bidirectional | 5 V tolerant I/O with TIM1_CH3N, TIM3_CH4, TIM8_CH3N, SPI5_NSS/I2S5_WS, DFSDM1_DATIN0, QUADSPI_CLK alternate functions; additional function ADC1_IN9. |
| 20 | PB2 | bidirectional | 5 V tolerant I/O with LPTIM1_OUT, DFSDM1_CKIN0, QUADSPI_CLK alternate functions; additional function BOOT1. |
| 21 | PB10 | bidirectional | 5 V tolerant I/O (FTf, I2C FM+ option) with TIM2_CH3, I2C2_SCL, SPI2_SCK/I2S2_CK, I2S3_MCK, USART3_TX, I2CFMP1_SCL, DFSDM2_CKOUT, SDIO_D7 alternate functions. |
| 22 | VCAP_1 | passive | Supply pin for the internal 1.2 V regulator output, connected to an external capacitor (VCAP_1). |
| 23 | VSS | power_in | Digital ground supply pin. |
| 24 | VDD | power_in | Digital supply pin for the application supply and I/Os (1.7 to 3.6 V). |
| 25 | PB12 | bidirectional | 5 V tolerant I/O with TIM1_BKIN, I2C2_SMBA, SPI2_NSS/I2S2_WS, SPI4_NSS, SPI3_SCK, USART3_CK, CAN2_RX, DFSDM1_DATIN1, UART5_RX, FSMC_D13 alternate functions. |
| 26 | PB13 | bidirectional | 5 V tolerant I/O with TIM1_CH1N, I2CFMP1_SMBA, SPI2_SCK/I2S2_CK, SPI4_SCK, USART3_CTS, CAN2_TX, DFSDM1_CKIN1, UART5_TX alternate functions. |
| 27 | PB14 | bidirectional | 5 V tolerant I/O (FTf, I2C FM+ option) with TIM1_CH2N, TIM8_CH2N, I2CFMP1_SDA, SPI2_MISO, USART3_RTS, DFSDM1_DATIN2, TIM12_CH1, FSMC_D0, SDIO_D6 alternate functions. |
| 28 | PB15 | bidirectional | 5 V tolerant I/O (FTf, I2C FM+ option) with RTC_REFIN, TIM1_CH3N, TIM8_CH3N, I2CFMP1_SCL, SPI2_MOSI/I2S2_SD, DFSDM1_CKIN2, TIM12_CH2, SDIO_CK alternate functions. |
| 29 | PA8 | bidirectional | 5 V tolerant I/O with MCO_1, TIM1_CH1, I2C3_SCL, DFSDM1_CKOUT, USART1_CK, UART7_RX, USB_FS_SOF, CAN3_RX, SDIO_D1 alternate functions. |
| 30 | PA9 | bidirectional | 5 V tolerant I/O with TIM1_CH2, DFSDM2_CKIN3, I2C3_SMBA, SPI2_SCK/I2S2_CK, USART1_TX, USB_FS_VBUS, SDIO_D2 alternate functions. |
| 31 | PA10 | bidirectional | 5 V tolerant I/O with TIM1_CH3, DFSDM2_DATIN3, SPI2_MOSI/I2S2_SD, SPI5_MOSI, USART1_RX, USB_FS_ID alternate functions. |
| 32 | PA11 | bidirectional | 5 V tolerant I/O with TIM1_CH4, DFSDM2_CKIN5, SPI2_NSS, SPI4_MISO, USART1_CTS, USART6_TX, CAN1_RX, USB_FS_DM, UART4_RX alternate functions. |
| 33 | PA12 | bidirectional | 5 V tolerant I/O with TIM1_ETR, DFSDM2_DATIN5, SPI2_MISO, SPI5_MISO, USART1_RTS, USART6_RX, CAN1_TX, USB_FS_DP, UART4_TX alternate functions. |
| 34 | PA13 | bidirectional | 5 V tolerant I/O with JTMS-SWDIO debug function after reset. |
| 35 | VSS | power_in | Digital ground supply pin. |
| 36 | VDD | power_in | Digital supply pin for the application supply and I/Os (1.7 to 3.6 V). |
| 37 | PA14 | bidirectional | 5 V tolerant I/O with JTCK-SWCLK debug function after reset. |
| 38 | PA15 | bidirectional | 5 V tolerant I/O with JTDI, TIM2_CH1/ETR, SPI1_NSS/I2S1_WS, SPI3_NSS/I2S3_WS, USART1_TX, UART7_TX, SAI1_MCLK_A, CAN3_TX alternate functions. |
| 39 | PB3 | bidirectional | 5 V tolerant I/O (FTf) with JTDO-SWO, TIM2_CH2, I2CFMP1_SDA, SPI1_SCK, SPI3_SCK, USART1_RX, UART7_RX, I2C2_SDA, SAI1_SD_A, CAN3_RX alternate functions. |
| 40 | PB4 | bidirectional | 5 V tolerant I/O with JTRST, TIM3_CH1, SPI1_MISO, SPI3_MISO, I2S3ext_SD, UART7_TX, I2C3_SDA, SAI1_SCK_A, CAN3_TX, SDIO_D0 alternate functions. |
| 41 | PB5 | bidirectional | 5 V tolerant I/O with LPTIM1_IN1, TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, CAN2_RX, SAI1_FS_A, UART5_RX, SDIO_D3 alternate functions. |
| 42 | PB6 | bidirectional | 5 V tolerant I/O with LPTIM1_ETR, TIM4_CH1, I2C1_SCL, DFSDM2_CKIN7, USART1_TX, CAN2_TX, QUADSPI_BK1_NCS, UART5_TX, SDIO_D0 alternate functions. |
| 43 | PB7 | bidirectional | 5 V tolerant I/O with LPTIM1_IN2, TIM4_CH2, I2C1_SDA, DFSDM2_DATIN7, USART1_RX, FSMC_NL alternate functions. |
| 44 | BOOT0 | input | Dedicated boot mode selection input; additional function VPP. |
| 45 | PB8 | bidirectional | 5 V tolerant I/O with LPTIM1_OUT, TIM4_CH3, TIM10_CH1, I2C1_SCL, SPI5_MOSI, DFSDM2_CKIN1, CAN1_RX, I2C3_SDA, UART5_RX, SDIO_D4 alternate functions. |
| 46 | PB9 | bidirectional | 5 V tolerant I/O with TIM4_CH4, TIM11_CH1, I2C1_SDA, SPI2_NSS/I2S2_WS, DFSDM2_DATIN1, CAN1_TX, I2C2_SDA, UART5_TX, SDIO_D5 alternate functions. |
| 47 | VSS | power_in | Digital ground supply pin. |
| 48 | VDD | power_in | Digital supply pin for the application supply and I/Os (1.7 to 3.6 V). |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDD-VSS external main supply voltage (including VDDA, VDD, VDDUSB and VBAT) | VDD-VSS | -0.3 | 4 | V | 81 | ||
| Input voltage on TTa pins | VIN | -0.3 | 4 | V | 81 | ||
| Input voltage on any other pin | VIN | -0.3 | 4 | V | 81 | ||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 81 | |||
| Variations between all the different ground pins including VREF- | /VSSX −VSS/ | 50 | mV | 81 | |||
| Total current into sum of all VDD_x power lines (source) | ΣIVDD | 180 | mA | 82 | |||
| Total current out of sum of all VSS_x ground lines (sink) | ΣIVSS | -180 | mA | 82 | |||
| Total current into VDDUSB power lines (source) | ΣIVDDUSB | 25 | mA | 82 | |||
| Maximum current into each VDD_x power line (source) | IVDD | 100 | mA | 82 | |||
| Maximum current out of each VSS_x ground line (sink) | IVSS | -100 | mA | 82 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 82 | |||
| Output current sourced by any I/O and control pin | IIO | -25 | mA | 82 | |||
| Total output current sunk by sum of all I/O and control pins | ΣIIO | 120 | mA | 82 | |||
| Total output current sunk by sum of all USB I/Os | ΣIIO | 25 | mA | Sum of all USB I/Os | 82 | ||
| Total output current sourced by sum of all I/Os and control pins | ΣIIO | -120 | mA | 82 | |||
| Injected current on FT and TC pins | IINJ(PIN) | -5 | 0 | mA | 82 | ||
| Injected current on TTa pins | IINJ(PIN) | -5 | 5 | mA | 82 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 82 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 82 | ||
| Maximum junction temperature | TJ | 125 | °C | 82 | |||
| Internal AHB clock frequency, Power Scale3 | fHCLK | 0 | 64 | MHz | Power Scale3: Regulator ON, VOS[1:0] = 0x01 | 83 | |
| Internal AHB clock frequency, Power Scale2 | fHCLK | 0 | 84 | MHz | Power Scale2: Regulator ON, VOS[1:0] = 0x10 | 83 | |
| Internal AHB clock frequency, Power Scale1 | fHCLK | 0 | 100 | MHz | Power Scale1: Regulator ON, VOS[1:0] = 0x11 | 83 | |
| Internal APB1 clock frequency | fPCLK1 | 0 | 50 | MHz | 83 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 100 | MHz | 83 | ||
| Standard operating voltage | VDD | 1.7 | 3.6 | V | 83 | ||
| Analog operating voltage (ADC limited to 1.2 M samples) | VDDA | 1.7 | 2.4 | V | ADC limited to 1.2 M samples; must be the same potential as VDD | 83 | |
| Analog operating voltage (ADC limited to 2.4 M samples) | VDDA | 2.4 | 3.6 | V | ADC limited to 2.4 M samples; must be the same potential as VDD | 83 | |
| USB supply voltage (VDDUSB), USB not used | VDDUSB | 1.7 | 3.3 | 3.6 | V | USB not used | 83 |
| USB supply voltage (VDDUSB), USB used | VDDUSB | 3 | 3.6 | V | USB used | 83 | |
| Backup operating voltage | VBAT | 1.65 | 3.6 | V | 83 | ||
| Regulator ON: 1.2 V internal voltage on VCAP_1/VCAP_2, VOS=0x01 | V12 | 1.08 | 1.14 | 1.2 | V | VOS[1:0] = 0x01; max frequency 64 MHz; guaranteed by test in production | 83 |
| Regulator ON: 1.2 V internal voltage on VCAP_1/VCAP_2, VOS=0x10 | V12 | 1.2 | 1.26 | 1.32 | V | VOS[1:0] = 0x10; max frequency 84 MHz; guaranteed by test in production | 83 |
| Regulator ON: 1.2 V internal voltage on VCAP_1/VCAP_2, VOS=0x11 | V12 | 1.26 | 1.32 | 1.38 | V | VOS[1:0] = 0x11; max frequency 100 MHz | 83 |
| Regulator OFF: 1.2 V external voltage on VCAP_1/VCAP_2, 64 MHz | V12 | 1.1 | 1.14 | 1.2 | V | Max frequency 64 MHz | 83 |
| Regulator OFF: 1.2 V external voltage on VCAP_1/VCAP_2, 84 MHz | V12 | 1.2 | 1.26 | 1.32 | V | Max frequency 84 MHz | 83 |
| Regulator OFF: 1.2 V external voltage on VCAP_1/VCAP_2, 100 MHz | V12 | 1.26 | 1.32 | 1.38 | V | Max frequency 100 MHz | 83 |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | 5.5 | V | 2 V ≤ VDD ≤ 3.6 V | 84 | |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | 5.2 | V | VDD ≤ 2 V | 84 | |
| Input voltage on TTa pins | VIN | -0.3 | V | Maximum printed as VDDA + 0.3 (not a numeric value) | 84 | ||
| Input voltage on BOOT0 pin | VIN | 0 | 9 | V | 84 | ||
| Power dissipation at TA = 85 °C for range 6, UFQFPN48 | PD | 625 | mW | TA = 85 °C for range 6, maximum power dissipation | 84 | ||
| Power dissipation at TA = 125 °C for range 3, UFQFPN48 | PD | 156 | mW | TA = 125 °C for range 3, maximum power dissipation | 84 | ||
| Ambient temperature for range 6, maximum power dissipation | TA | -40 | 85 | °C | Maximum power dissipation | 84 | |
| Ambient temperature for range 6, low power dissipation | TA | -40 | 105 | °C | Low power dissipation | 84 | |
| Ambient temperature for range 7, maximum power dissipation | TA | -40 | 105 | °C | Maximum power dissipation | 84 | |
| Ambient temperature for range 7, low power dissipation | TA | -40 | 125 | °C | Low power dissipation | 84 | |
| Ambient temperature for range 3, maximum power dissipation | TA | -40 | 125 | °C | Maximum power dissipation | 84 | |
| Ambient temperature for range 3, low power dissipation | TA | -40 | 130 | °C | Low power dissipation | 84 | |
| Junction temperature range, range 6 | TJ | -40 | 105 | °C | Range 6 | 84 | |
| Junction temperature range, range 7 | TJ | -40 | 125 | °C | Range 7 | 84 | |
| Junction temperature range, range 3 | TJ | -40 | 130 | °C | Range 3 | 84 | |
| Power-on/power-down reset threshold, falling edge | VPOR/PDR | 1.6 | 1.68 | 1.76 | V | Falling edge | 87 |
| Power-on/power-down reset threshold, rising edge | VPOR/PDR | 1.64 | 1.72 | 1.8 | V | Rising edge | 87 |
| PDR hysteresis | VPDRhyst | 40 | mV | 87 | |||
| PVD hysteresis | VPVDhyst | 100 | mV | 87 | |||
| BOR hysteresis | VBORhyst | 100 | mV | 88 | |||
| Supply current in Stop mode, flash in Stop mode, low power regulator usage, VDD=3.6 V | IDD_STOP | 44.1 | 82.5 | µA | Flash in Stop mode, all oscillators OFF, no independent watchdog; TA = 25 °C | 99 | |
| Supply current in Standby mode, RTC and LSE OFF, VDD=3.6 V | IDD_STBY | 2.5 | 4 | µA | RTC and LSE OFF; TA = 25 °C | 100 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
STM32F423CHU6 - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: UFQFPN-48(7x7), generated on the KiCad land (body 7 x 7 mm, terminals on the pads, 0.55 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
stm32f423chu6-etched.step/stm32f423chu6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f423chu6.step/stm32f423chu6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (210 pp, sha256
95e19737006950a4, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).