Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3437IDD#TRPBF

Analog Devices · DC-DC Converters · DFN-10-EP(3x3)

LT3437IDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW output SW is the emitter of the on-chip power NPN switch, driven up to the input voltage during on-time, and needs an external Schottky catch diode to clamp negative excursions; SW operating rating is 60V.
2 VIN power_in VIN is the collector of the on-chip power switch and powers the internal control circuitry when BIAS is not present; operating maximum is 60V, with 80V allowed for 100ms transients at less than 15% duty cycle.
3 BOOST power_in BOOST supplies the drive voltage above VIN for the internal switch, with BOOST pin voltage above SW limited to 35V and operating voltage limited to 75V.
4 GND power_in GND is the reference for the regulated output and also the heat sink, and should be soldered together with the exposed pad to a copper ground plane.
5 CSS passive A capacitor from CSS to the regulated output sets the output voltage ramp rate at start-up, and the soft-start is defeated for FB above 0.9V (typical); CSS absolute maximum is 6V.
6 BIAS input BIAS connected to the regulated output reduces input current and improves efficiency, with a minimum output setting for this mode typically 2.7V; BIAS operating maximum is 60V.
7 VC passive VC is the error amplifier output and peak switch current comparator input used for compensation, sitting at about 0.45V at light load and 1.5V at maximum load, and driving it to ground disables switching.
8 FB input FB is the feedback input regulated to 1.25V through an external divider, and when it drops below 0.9V the switching frequency is reduced, SYNC is disabled and soft-start is enabled; FB absolute maximum is 6V.
9 SYNC input SYNC synchronizes the internal oscillator to an external logic signal of 25% to 75% duty cycle over a range up to 700kHz, and a level above 2V disables Burst Mode operation; SYNC absolute maximum is 6V.
10 SHDN input SHDN turns the regulator off and reduces input current to less than 1µA when below its 1.3V typical threshold, requiring above 1.3V to enable; SHDN operating maximum is 60V, with 80V allowed for 100ms transients at less than 15% duty cycle.
11 GND (EXPOSED PAD) power_in The exposed pad is ground and must be soldered to the PCB and to GND (pin 4) for low thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-10-EP(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
SHDN Threshold VSHDN 1.15 1.3 1.45 V 2
SHDN Input Current ISHDN 5 30 µA SHDN = 12V 2
Minimum Input Voltage 2.5 3 V Note 3 2
Supply Shutdown Current IVINS 0.1 2 µA SHDN = 0V, BOOST = 0V, FB/PGFB = 0V, BIAS = 0V 2
Supply Sleep Current 150 300 µA BIAS = 0V, FB = 1.35V 2
Supply Sleep Current 45 75 µA FB = 1.35V 2
Supply Quiescent Current IVIN 1.35 2 mA BIAS = 0V, FB = 1.15V, VC = 0.8V, SYNC = 2V 3
Supply Quiescent Current IVIN 0.475 1 mA BIAS = 5V, FB = 1.15V, VC = 0.8V, SYNC = 2V 3
Minimum BIAS Voltage 2.7 3.15 V Note 5 3
BIAS Sleep Current IBIASS 110 180 µA Note 4 3
BIAS Quiescent Current IBIAS 0.75 1 mA SYNC = 2V 3
Minimum Boost Voltage 1.8 2.5 V ISW = 500mA, Note 6 3
Input Boost Current 11 16 mA ISW = 0.5A, Note 7 3
Input Boost Current 8 13 mA ISW = 0.25A, Note 7 3
Reference Voltage VREF 1.225 1.25 1.275 V 3.3V < VVIN < 80V 3
FB Input Bias Current IFB 50 200 nA 3
EA Source Current 15 35 55 µA FB = 1.15V 3
EA Sink Current 15 30 55 µA FB = 1.35V 3
VC High Clamp 1.5 1.75 2.1 V 3
IPK SW Current Limit IPK 500 650 900 mA 3
SW VCESAT Switch Saturation Voltage VCESAT 200 400 mV ISW = 250mA, Note 9 3
SW VCESAT Switch Saturation Voltage VCESAT 400 800 mV ISW = 500mA, Note 9 3
Switching Frequency 165 200 240 kHz 3
SYNC Frequency Range 240 700 kHz 3
Minimum SYNC Amplitude 1.5 2 V 3
CSS Current Threshold ICSS 4 10 16 µA FB = 0V, Note 10 3
Maximum Duty Cycle 95 % 3
EA Voltage Gain 900 V/V Note 8 3
EA Transconductance gm 650 µMho dI(VC) = ±10µA 3
VC to SW Transconductance gm 1 A/V 3
VC Switching Threshold 500 mV VSYNC = 2V 3
SYNC Input Impedance 50 kΩ 3
VIN, SHDN, BIAS, SW Operating 60 V Operating 2
VIN, SHDN 100ms Transient 80 V 100ms transient, <15% duty cycle 2
BOOST Pin Above SW 35 V 2
BOOST Pin Voltage Operating 75 V Operating 2
BOOST Pin 100ms Transient 85 V 100ms transient, <15% duty cycle 2
SYNC, CSS, FB 6 V 2
Storage Temperature Range (DD Package) Tstg -65 125 °C DD package 2
Operating Junction Temperature Range (LT3437IDD) -40 125 °C Note 2 2
Thermal Resistance Junction to Ambient θJA 45 °C/W 2
Thermal Resistance Junction to Exposed Pad θJC(PAD) 10 °C/W 2

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper resistance. Pin 4/Pin 8 and the exposed die pad, Pin 11/Pin 17, are connected by a continuous copper plate that runs 20

CAD (KiCad official)

  • Symbol: LT3437IDD#TRPBF
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: lt3437idd-trpbf-etched.step / lt3437idd-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3437idd-trpbf.step / lt3437idd-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (28 pp, sha256 e2cb79c469ba5793, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF