Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

OPA322SAIDBVR

Texas Instruments · Operational Amplifier · SOT-23-6

OPA322SAIDBVR from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 V+ power_in Positive supply pin; specified operating supply range is 1.8 V to 5.5 V (or ±0.9 V to ±2.75 V split supply), absolute maximum (V+)-(V-) supply voltage is 6 V; a local 0.001 µF to 0.1 µF ceramic bypass capacitor is recommended.
2 SHDN input Active-high shutdown/enable input referenced to V-; a logic high of (V+)-0.1 V up to V+ enables the amplifier while a logic low of (V-)+0.1 V down to V- disables it, with 5.5 V max allowed relative to V-; the pin must be driven to a valid level and not left floating, and disabled channels draw a typical 0.1 µA (max 0.5 µA) quiescent current.
3 -IN input Inverting input of the operational amplifier; common-mode input voltage range is (V-)-0.1 V to (V+)+0.1 V, and input current should be limited to 10 mA or less (via series resistor) for signals overdriving the supply rails by more than 0.5 V.
4 +IN input Non-inverting input of the operational amplifier; common-mode input voltage range is (V-)-0.1 V to (V+)+0.1 V, and input current should be limited to 10 mA or less for overdrive protection.
5 V- power_in Negative supply pin (ground reference in single-supply operation); together with V+ establishes the 1.8 V to 5.5 V (or ±0.9 V to ±2.75 V) supply range and should have a local ceramic bypass capacitor.
6 OUT output Amplifier output; rail-to-rail output typically swings within 10 mV (20 mV max) of either supply rail into a 10-kΩ load, delivers up to ±65 mA short-circuit current at VS=5.5 V, and enters a high-impedance state when the device is disabled via SHDN.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOT-23-6
Category Amplifiers/Comparators
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage, VS = (V+) – (V–) VS 6 V 2
Signal input pins current -10 10 mA 2
Operating temperature TA -40 150 °C Over operating free-air temperature range 2
Storage temperature Tstg -65 150 °C 2
Junction temperature TJ 150 °C 2
ESD Human body model (HBM) 4000 V 2
ESD Charged device model (CDM) 1000 V 2
ESD Machine model (MM) 200 V 2
Specified voltage range VS 1.8 5.5 V 4
Specified temperature range -40 125 °C 4
Operating range -40 150 °C 4
Input offset voltage VOS 0.5 2 mV 3
Input offset voltage vs temperature dVOS/dT 1.8 6 μV/°C VS = +5.5 V 3
Power supply rejection PSR 10 50 μV/V VS = +1.8 V to +5.5 V 3
Power supply rejection over temperature PSR 20 65 μV/V Over temperature; VS = +1.8 V to +5.5 V 3
Common-mode rejection ratio CMRR 90 100 dB (V–) – 0.1 V < VCM < (V+) + 0.1 V 3
Common-mode rejection ratio over temperature CMRR 90 dB Over temperature 3
Input bias current IB -10 0.2 10 pA 3
Input bias current IB -50 50 pA TA = –40°C to +85°C 3
Input bias current over temperature (OPA322, OPA322S) IB -800 800 pA Over temperature; TA = –40°C to +125°C 3
Input offset current IOS -10 0.2 10 pA 3
Input offset current IOS -50 50 pA TA = –40°C to +85°C 3
Input offset current over temperature IOS -400 400 pA TA = –40°C to +125°C 3
Open-loop voltage gain AOL 100 130 dB 0.1 V < VO < (V+) – 0.1 V, RL = 10 kΩ 3
Open-loop voltage gain (second row) AOL 94 dB 0.1 V < VO < (V+) – 0.1 V, RL = 10 kΩ 3
Voltage output swing from rails VO 10 20 mV RL = 10 kΩ, both rails 4
Voltage output swing from rails over temperature VO 30 mV Over temperature; RL = 10 kΩ 4
Short-circuit current ISC -65 65 mA VS = 5.5 V 4
Quiescent current per amplifier IQ 1.6 1.9 mA IO = 0 mA, VS = +5.5 V 4
Quiescent current per amplifier over temperature IQ 2 mA Over temperature; IO = 0 mA, VS = +5.5 V 4
Quiescent current per amplifier in shutdown IQSD 0.1 0.5 µA All amplifiers disabled, SHDN = VS– 4
Junction-to-ambient thermal resistance θJA 177.5 °C/W OPA322S DBV 6-pin package 5
Junction-to-case(top) thermal resistance θJC(top) 108.9 °C/W OPA322S DBV 6-pin package 5
Junction-to-board thermal resistance θJB 27.4 °C/W OPA322S DBV 6-pin package 5
Junction-to-top characterization parameter ψJT 13.3 °C/W OPA322S DBV 6-pin package 5
Junction-to-board characterization parameter ψJB 26.9 °C/W OPA322S DBV 6-pin package 5

CAD (KiCad official)

  • Symbol: OPA322SAIDBVR
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-23-6 (KiCad packages3D, STEP)
  • 3D model files: opa322saidbvr-etched.step / opa322saidbvr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); opa322saidbvr.step / opa322saidbvr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (51 pp, sha256 b4b7c5ce416fcd4d, retrieved 2026-09-23, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF