component
AT24C08C-XHM-T
Public Made by Adomby adom
Microchip Tech EEPROM, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownAT24C08C-XHM-T
Microchip Tech · EEPROM · TSSOP-8
AT24C08C-XHM-T from Microchip Tech, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No Connect pin on the TSSOP-8 package, with no internal connection stated by the datasheet. |
| 2 | NC | unconnected | On the AT24C08C this pin is a no connect; it is the A1 device address input only on the AT24C04C. |
| 3 | A2 | input | Device address input that is hard-wired to GND or VCC and is internally pulled down to GND if not driven; Microchip recommends a pull-up of 10 kΩ or less when one is used. |
| 4 | GND | power_in | Ground reference for the power supply, which should be connected to the system ground. |
| 5 | SDA | bidirectional | Open-drain bidirectional serial data pin that must be pulled high with an external pull-up resistor not exceeding 10 kΩ. |
| 6 | SCL | input | Serial clock input where SDA data is latched on the rising edge and output data is clocked out on the falling edge, and which must be forced high when the bus is idle or pulled high externally. |
| 7 | WP | input | Write-protect input where connecting it to GND allows normal writes and connecting it to VCC inhibits all writes to the protected memory (full array); it is internally pulled down to GND if left floating. |
| 8 | VCC | power_in | Device power supply pin; operation at invalid VCC voltages may produce spurious results and should not be attempted. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Temperature (Case), Industrial Range | -40 | 85 | °C | 9 | |||
| VCC Power Supply, Low Voltage Grade | VCC | 1.7 | 5.5 | V | 9 | ||
| Temperature under bias | -55 | 125 | °C | 9 | |||
| Storage temperature | -65 | 150 | °C | 9 | |||
| VCC supply voltage | VCC | 6.25 | V | 9 | |||
| Voltage on any pin with respect to ground | -1 | 7 | V | 9 | |||
| DC output current | 5 | mA | 9 | ||||
| ESD protection (printed as >4 kV) | 4 | kV | Printed as '>4 kV' | 9 | |||
| Supply Voltage | VCC | 1.7 | 5.5 | V | 9 | ||
| Supply Current Read | ICC1 | 0.4 | 1 | mA | VCC = 5.0V, Read at 100 kHz | 9 | |
| Supply Current Write | ICC2 | 2 | 3 | mA | VCC = 5.0V, Write at 100 kHz | 9 | |
| Standby Current | ISB | 1 | μA | VCC = 1.7V, VIN = VCC or GND | 9 | ||
| Standby Current | ISB | 6 | μA | VCC = 5.5V, VIN = VCC or GND | 9 | ||
| Input Leakage Current | ILI | 0.1 | 3 | μA | VIN = VCC or GND | 10 | |
| Output Leakage Current | ILO | 0.05 | 3 | μA | VOUT = VCC or GND | 10 | |
| Input Low Level | VIL | -0.6 | V | Note 2 | 10 | ||
| Output Low Level | VOL1 | 0.2 | V | VCC = 1.7V, IOL = 0.15 mA | 10 | ||
| Output Low Level | VOL2 | 0.4 | V | VCC = 3.0V, IOL = 2.1 mA | 10 | ||
| Clock Frequency, SCL (Fast Mode) | fSCL | 400 | kHz | VCC = 1.7V to 2.5V | 10 | ||
| Clock Frequency, SCL (Fast Mode Plus) | fSCL | 1000 | kHz | VCC = 2.5V to 5.5V | 10 | ||
| Clock Pulse Width Low (Fast Mode) | tLOW | 1200 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Clock Pulse Width Low (Fast Mode Plus) | tLOW | 500 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Clock Pulse Width High (Fast Mode) | tHIGH | 600 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Clock Pulse Width High (Fast Mode Plus) | tHIGH | 400 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Input Filter Spike Suppression (Fast Mode) | tI | 100 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Input Filter Spike Suppression (Fast Mode Plus) | tI | 50 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Clock Low to Data Out Valid (Fast Mode) | tAA | 100 | 900 | ns | VCC = 1.7V to 2.5V | 10 | |
| Clock Low to Data Out Valid (Fast Mode Plus) | tAA | 50 | 450 | ns | VCC = 2.5V to 5.5V | 10 | |
| Bus Free Time between Stop and Start (Fast Mode) | tBUF | 1200 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Bus Free Time between Stop and Start (Fast Mode Plus) | tBUF | 500 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Start Hold Time (Fast Mode) | tHD.STA | 600 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Start Hold Time (Fast Mode Plus) | tHD.STA | 250 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Start Set-up Time (Fast Mode) | tSU.STA | 600 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Start Set-up Time (Fast Mode Plus) | tSU.STA | 250 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Data In Hold Time (Fast Mode) | tHD.DAT | 0 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Data In Hold Time (Fast Mode Plus) | tHD.DAT | 0 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Data In Set-up Time (Fast Mode) | tSU.DAT | 100 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Data In Set-up Time (Fast Mode Plus) | tSU.DAT | 100 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Inputs Rise Time (Fast Mode) | tR | 300 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Inputs Rise Time (Fast Mode Plus) | tR | 300 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Inputs Fall Time (Fast Mode) | tF | 300 | ns | VCC = 1.7V to 2.5V | 10 | ||
| Inputs Fall Time (Fast Mode Plus) | tF | 100 | ns | VCC = 2.5V to 5.5V | 10 | ||
| Stop Set-up Time (Fast Mode) | tSU.STO | 600 | ns | VCC = 1.7V to 2.5V | 11 | ||
| Stop Set-up Time (Fast Mode Plus) | tSU.STO | 250 | ns | VCC = 2.5V to 5.5V | 11 | ||
| Data Out Hold Time (Fast Mode) | tDH | 50 | ns | VCC = 1.7V to 2.5V | 11 | ||
| Data Out Hold Time (Fast Mode Plus) | tDH | 50 | ns | VCC = 2.5V to 5.5V | 11 | ||
| Write Cycle Time (Fast Mode) | tWR | 5 | ms | VCC = 1.7V to 2.5V | 11 | ||
| Write Cycle Time (Fast Mode Plus) | tWR | 5 | ms | VCC = 2.5V to 5.5V | 11 | ||
| Time required after VCC is stable before the device can accept commands | tPUP | 100 | µs | 12 | |||
| Power-on Reset Threshold Voltage | VPOR | 1.5 | V | 12 | |||
| Minimum time at VCC = 0V between power cycles | tPOFF | 500 | ms | 12 | |||
| Input/Output Capacitance (SDA) | CI/O | 8 | pF | VI/O = 0V | 12 | ||
| Input Capacitance (A1, A2 and SCL) | CIN | 6 | pF | VIN = 0V | 12 | ||
| Write Endurance | 1e+06 | Write Cycles | TA = 25°C, VCC = 3.3V, Page Write mode | 12 | |||
| Data Retention | 100 | Years | TA = 55°C | 12 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 29 |
CAD (KiCad official)
- Symbol:
AT24C08C-XHM-T - Footprint:
Package_SO:TSSOP-8_3x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
at24c08c-xhm-t-etched.step/at24c08c-xhm-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);at24c08c-xhm-t.step/at24c08c-xhm-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (46 pp, sha256
26bee522edd339ed, retrieved 2026-10-21, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).