component
TPS65101RGER
Public Made by Adomby adom
Texas Instruments LCD Drivers, VQFN-24-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTPS65101RGER
Texas Instruments · LCD Drivers · VQFN-24-EP(4x4)
TPS65101RGER from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | COMP | passive | Compensation pin for the main boost converter; a small capacitor is connected to this pin. |
| 2 | ENR | input | Enable pin of the linear regulator controller; it must be terminated and not left floating, with logic high enabling the regulator and logic low putting it in shutdown. |
| 3 | EN | input | Enable pin of the device; it must be terminated and not left floating, with logic high enabling the device and logic low shutting it down. |
| 4 | FB1 | input | Feedback pin of the boost converter (VO1). |
| 5 | FB4 | input | Feedback pin of the linear regulator controller, which is set to a fixed output of 3.3 V or 3 V depending on the version. |
| 6 | BASE | output | Base drive output for the external transistor; if the linear regulator is not needed, pull this pin against VIN. |
| 7 | VIN | power_in | Input voltage pin of the device, specified for 2.7 V to 5.8 V. |
| 8 | SW | passive | Switch pin of the boost converter; voltage on SW is rated -0.3 V to 20 V absolute maximum. |
| 9 | SW | passive | Switch pin of the boost converter; voltage on SW is rated -0.3 V to 20 V absolute maximum. |
| 10 | PGND | power_in | Power ground; the PowerPAD / exposed thermal die must be connected to the power ground pins. |
| 11 | PGND | power_in | Power ground; the PowerPAD / exposed thermal die must be connected to the power ground pins. |
| 12 | SUP | input | Supply pin of the positive and negative charge pumps, boost converter gate drive and VCOM buffer; it must be connected to the boost converter output and not to any other voltage source, and a bypass capacitor is not recommended directly on this pin. |
| 13 | VCOM | output | VCOM buffer output; voltage on VCOM is rated -0.3 V to 15 V absolute maximum. |
| 14 | VCOMIN | input | Positive input terminal of the VCOM buffer; when the buffer is not used it can be connected to GND to reduce the overall quiescent current. |
| 15 | FB3 | input | Feedback pin of the positive charge pump. |
| 16 | OUT3 | output | Positive charge pump output (VO3); voltage on VOUT3 is rated -0.3 V to 30 V absolute maximum. |
| 17 | C2+ | passive | Positive terminal for the charge pump flying capacitor; this pin should be left open if the device runs in voltage doubler mode. |
| 18 | C2-/MODE | passive | Negative terminal of the charge pump flying capacitor and charge pump MODE pin; the flying capacitor connected here selects voltage tripler mode, while connecting this pin to GND (flying capacitor removed) selects voltage doubler mode. |
| 19 | C1+ | passive | Positive terminal of the charge pump flying capacitor. |
| 20 | C1- | passive | Negative terminal of the charge pump flying capacitor. |
| 21 | DRV | output | External charge pump driver output; voltage on DRV is rated -0.3 V to 15 V absolute maximum. |
| 22 | GND | power_in | Ground pin of the device. |
| 23 | REF | output | Internal reference output, typically 1.23 V; voltage on REF is rated -0.3 V to 4 V absolute maximum. |
| 24 | FB2 | input | Feedback pin of the negative charge pump. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-24-EP(4x4) |
| Category | LED Drivers |
| Pins | 25 |
CAD (KiCad official)
- Symbol:
TPS65101RGER - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm - 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
tps65101rger-etched.step/tps65101rger-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps65101rger.step/tps65101rger.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (43 pp, sha256
2bf67383027da5b0, retrieved 2026-10-08, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).