Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

M24512-DRDW8TP

STMicroelectronics · EEPROM · TSSOP-8

M24512-DRDW8TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 E0 input Chip Enable input that sets the LSB (b1) of the 7-bit device select code, to be tied to VCC or VSS, and read as low when left floating.
2 E1 input Chip Enable input that sets bit b2 of the 7-bit device select code, to be tied to VCC or VSS, and read as low when left floating.
3 E2 input Chip Enable input that sets bit b3 of the 7-bit device select code, to be tied to VCC or VSS, and read as low when left floating.
4 VSS power_in Ground, the reference for the VCC supply voltage.
5 SDA bidirectional Serial Data input/output with an open-drain output that needs a pull-up resistor to VCC.
6 SCL input Serial Clock input that strobes data on SDA in and out, supporting up to 1 MHz.
7 WC input Write Control input, active high, that disables writes to the entire memory array when driven high, and enables writes when driven low or left floating.
8 VCC power_in Supply voltage pin, 1.7 V to 5.5 V, with a 10 nF to 100 nF decoupling capacitor recommended close to VCC/VSS.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package TSSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC 1.7 5.5 V 27
Ambient operating temperature TA -40 105 °C 27
Ambient operating temperature (abs max) -40 130 °C 26
Storage temperature TSTG -65 150 °C 26
Input or output range VIO -0.5 6.5 V 26
DC output current IOL 5 mA SDA = 0 26
Supply voltage (abs max) VCC -0.5 6.5 V 26
Electrostatic pulse (HBM) VESD 4000 V Human Body model 26
Write cycle endurance Ncycle 4e+06 Write cycle TA ≤ 25 °C, 1.7 V < VCC < 5.5 V 27
Write cycle endurance Ncycle 1.2e+06 Write cycle TA = 85 °C, 1.7 V < VCC < 5.5 V 27
Write cycle endurance Ncycle 900000 Write cycle TA = 105 °C, 1.7 V < VCC < 5.5 V 27
Input capacitance (SDA) CIN 8 pF 28
Input capacitance (other pins) CIN 6 pF 28
Input impedance (E2, E1, E0, WC) ZL 30 kΩ VIN < 0.3 VCC 28
Input impedance (E2, E1, E0, WC) ZH 500 kΩ VIN > 0.7 VCC 28
Input leakage current (SCL, SDA, Ei) ILI -2 2 µA VIN = VSS or VCC, device in Standby mode 29
Output leakage current ILO -2 2 µA SDA in Hi-Z, external voltage applied on SDA: VSS or VCC 29
Supply current (Read) ICC 2 mA fC = 400 kHz, VCC = 5.5 V 29
Supply current (Read) ICC 1 mA fC = 400 kHz, VCC = 1.7 V 29
Supply current (Write) ICC0 2 mA During tW 29
Standby supply current ICC1 1 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 1.7 V 29
Standby supply current ICC1 2 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 2.5 V 29
Standby supply current ICC1 3 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 5.5 V 29
Standby supply current ICC1 2.5 µA Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 1.7 V 29
Standby supply current ICC1 5 µA Device not selected, t° = 105 °C, VIN = VSS or VCC, VCC = 5.5 V 29
Input low voltage (SCL, SDA, WC, Ei) VIL -0.45 0.3 V max is 0.3 VCC 29
Input high voltage (SCL, SDA) VIH 0.7 6.5 V min is 0.7 VCC 29
Input high voltage (WC, Ei) VIH 0.7 0.6 V min is 0.7 VCC; max is VCC +0.6 29
Output low voltage VOL 0.4 V IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V 29
Output low voltage VOL 0.3 V IOL = 1 mA, VCC = 1.7 V 29
Internal reset threshold voltage VRES 0.5 1.5 V 29
Clock frequency (400 kHz) fC 400 kHz 30
Clock pulse width high (400 kHz) tCHCL 600 ns 30
Clock pulse width low (400 kHz) tCLCH 1300 ns 30
SDA (out) fall time (400 kHz) tQL1QL2 20 120 ns CL = 10 pF 30
Data in set up time (400 kHz) tDXCH 100 ns 30
Data in hold time (400 kHz) tCLDX 0 ns 30
Data out hold time (400 kHz) tCLQX 100 ns 30
Clock low to next data valid (400 kHz) tCLQV 900 ns 30
Start condition setup time (400 kHz) tCHDL 600 ns 30
Start condition hold time (400 kHz) tDLCL 600 ns 30
Stop condition set up time (400 kHz) tCHDH 600 ns 30
Time between Stop and next Start (400 kHz) tDHDL 1300 ns 30
WC set up time (400 kHz) tWLDL 0 µs 30
WC hold time (400 kHz) tDHWH 1 µs 30
Write time (400 kHz) tW 4 ms 30
Pulse width ignored (400 kHz) tNS 80 ns input filter on SCL and SDA, single glitch 30
Clock frequency (1 MHz) fC 0 1 MHz 31
Clock pulse width high (1 MHz) tCHCL 260 ns 31
Clock pulse width low (1 MHz) tCLCH 400 ns 31
SDA (out) fall time (1 MHz) tQL1QL2 120 ns 31
Data in setup time (1 MHz) tDXCH 50 ns 31
Data out hold time (1 MHz) tCLQX 100 ns 31
Clock low to next data valid (1 MHz) tCLQV 450 ns 31
Write time (1 MHz) tW 4 ms 31

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST 26

CAD (KiCad official)

  • Symbol: M24512-DRDW8TP
  • Footprint: Package_SO:TSSOP-8_3x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: m24512-drdw8tp-etched.step / m24512-drdw8tp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m24512-drdw8tp.step / m24512-drdw8tp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (42 pp, sha256 5cd7685718446d9b, retrieved 2026-10-22, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF