component
F1478NLGA8
Public Made by Adomby adom
RENESAS RF Amplifiers, QFN-16(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownF1478NLGA8
RENESAS · RF Amplifiers · QFN-16(3x3)
F1478NLGA8 from RENESAS, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Internally grounded; this pin must be grounded with a via as close to the pin as possible. |
| 2 | RFIN | input | RF input internally matched to 50Ω; an external DC block must be used. |
| 3 | GND | power_in | Internally grounded; this pin must be grounded with a via as close to the pin as possible. |
| 4 | VCC-RF | power_in | Pulled up to Vcc through an inductor with bypass capacitors placed as close to the pin as possible; it also carries an RF signal. |
| 5 | NC | unconnected | No internal connection; may be left unconnected or connected to ground (recommended) using a via placed as close to the pin as possible. |
| 6 | NC | unconnected | No internal connection; may be left unconnected or connected to ground (recommended) using a via placed as close to the pin as possible. |
| 7 | NC | unconnected | No internal connection; may be left unconnected or connected to ground (recommended) using a via placed as close to the pin as possible. |
| 8 | NC | unconnected | No internal connection; may be left unconnected or connected to ground (recommended) using a via placed as close to the pin as possible. |
| 9 | GND | power_in | Internally grounded per Table 1; this pin must be grounded with a via as close to the pin as possible. |
| 10 | RFOUT | output | RF output that is pulled up to Vcc through an inductor and requires an external DC block. |
| 11 | RFOUT | output | RF output that is pulled up to Vcc through an inductor and requires an external DC block. |
| 12 | GND | power_in | Internally grounded; this pin must be grounded with a via as close to the pin as possible. |
| 13 | BIAS_1 | passive | Connected via a resistor to a common Vcc with bypass capacitors placed as close to the pin as possible, as shown in the Typical Application Circuit. |
| 14 | BIAS_2 | passive | Connected via an inductor to ground. |
| 15 | RSET | passive | Connected via a resistor to ground; the resistor value sets the device into its low or high power mode. |
| 16 | STBY | input | Standby pin, 1.8V logic compatible: logic LOW powers the amplifier off, while logic HIGH or an unconnected pin gives full operation. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | QFN-16(3x3) |
| Category | RF & Radio |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC to GND | VCC | -0.3 | 6 | V | 9 | ||
| STBY voltage | VCTL | -0.3 | V | max printed as lower of (5.0, VCC + 0.25) | 9 | ||
| BIAS_1 current into pin | IBIAS_1 | 20 | mA | BIAS_1 (into pin) | 9 | ||
| BIAS_2 current out of pin | IBIAS_2 | 10 | mA | BIAS_2 (out of pin) | 9 | ||
| RFIN externally applied DC voltage | VRFIN | -0.5 | 0.5 | V | 9 | ||
| RFOUT externally applied DC voltage | VRFOUT | -0.5 | 5.5 | V | 9 | ||
| Maximum CW input power, Standby ON | PMAX_IN_ON | 21 | dBm | 24 hours, VCC = 5V, TEPAD = 115°C, VSWR < 2:1, Standby = logic HIGH ON state | 9 | ||
| Maximum CW input power, Standby OFF | PMAX_IN_OFF | 21 | dBm | 24 hour, VCC = 5V, TEPAD = 115°C, VSWR < 2:1, Standby = logic LOW OFF state | 9 | ||
| Continuous power dissipation | PDISS | 1.8 | W | 9 | |||
| Storage temperature range | Tst | -65 | 150 | °C | 9 | ||
| Lead temperature (soldering) | 260 | °C | soldering, 10 s | 9 | |||
| ESD HBM | VESDHBM | 500 | V | JEDEC/ESDA JS-001-2012 (Class 1B) | 9 | ||
| ESD CDM | VESDCDM | 1000 | V | JEDEC 22-C101F (Class C3) | 9 | ||
| Power supply voltage | VCC | 3.15 | 5.25 | V | 10 | ||
| Operating temperature range (exposed paddle) | TEPAD | -40 | 115 | °C | Exposed paddle | 10 | |
| Junction temperature, amplifier | Tj | 150 | °C | 10 | |||
| RF frequency range, Band 2p0 tuning set | fRF | 1.8 | 2.2 | GHz | Band 2p0 Tuning Set | 10 | |
| RF frequency range, Band 2p5 tuning set | fRF | 2.3 | 2.7 | GHz | Band 2p5 Tuning Set | 10 | |
| RF frequency range, Band 3p5 tuning set | fRF | 3.3 | 3.8 | GHz | Band 3p5 Tuning Set | 10 | |
| RF frequency range, Band 4p7 tuning set | fRF | 4.4 | 5 | GHz | Band 4p7 Tuning Set | 10 | |
| Logic input high | VIH | 1.17 | V | maximum printed as VCC | 11 | ||
| Logic input low | VIL | -0.3 | 0.63 | V | 11 | ||
| Logic current | ISTBY | -10 | 10 | µA | STBY | 11 | |
| Quiescent current, low power mode | ICC_QL | 100 | 130 | mA | Low Power Mode: R3 = 16kΩ | 11 | |
| Quiescent current, high power mode | ICC_QH | 140 | 178 | mA | High Power Mode: R3 = 10kΩ | 11 | |
| Standby current | ICC_STBY | 1.5 | mA | STBY = LOW | 11 | ||
| Standby switching time, on | tON | 270 | ns | 50% STBY control to within 0.5dB of the on-state final gain value | 11 | ||
| Standby switching time, off | tOFF | 60 | ns | 50% STBY control to 30dBc below nominal gain value | 11 | ||
| Noise figure, Band 2p0 low power | NF | 1.7 | dB | 12 | |||
| Output third order intercept point, Band 2p0 low power | OIP3 | 32 | dBm | POUT = +2dBm / tone, 1MHz tone separation | 12 | ||
| Output 1dB compression point, Band 2p0 low power | OP1dB | 23.3 | dBm | 12 | |||
| Noise figure, Band 2p0 high power | NF | 1.8 | dB | 13 | |||
| Output 1dB compression point, Band 2p0 high power | OP1dB | 24 | dBm | 13 | |||
| Noise figure, Band 2p5 low power | NF | 1.7 | dB | 14 | |||
| Output third order intercept point, Band 2p5 low power | OIP3 | 32.2 | dBm | POUT = +2dBm / tone, 1MHz tone separation | 14 | ||
| Output 1dB compression point, Band 2p5 low power | OP1dB | 22.8 | dBm | 14 | |||
| Noise figure, Band 2p5 high power | NF | 1.6 | dB | 15 | |||
| Output third order intercept point, Band 2p5 high power | OIP3 | 35.7 | dBm | POUT = +2dBm / tone, 1MHz tone separation | 15 | ||
| Output 1dB compression point, Band 2p5 high power | OP1dB | 23.6 | dBm | 15 | |||
| Noise figure, Band 3p5 low power | NF | 1.7 | 2.5 | dB | 16 | ||
| Output third order intercept point, Band 3p5 low power | OIP3 | 31.2 | 32.3 | dBm | POUT = +2dBm / tone, 1MHz tone separation | 16 | |
| Output third order intercept point, Band 3p5 low power, VCC range | OIP3 | 29.3 | dBm | POUT = +2dBm / tone, VCC = 4.75V to 5.25V, TEPAD = -40°C to +115°C | 16 | ||
| Output 1dB compression point, Band 3p5 low power | OP1dB | 21.2 | 22.4 | dBm | 16 | ||
| Output 1dB compression point, Band 3p5 low power, VCC range | OP1dB | 19.3 | dBm | VCC = 4.75V to 5.25V, TEPAD = -40°C to +115°C | 16 | ||
| Noise figure, Band 3p5 high power | NF | 1.8 | 2.5 | dB | 17 | ||
| Output third order intercept point, Band 3p5 high power | OIP3 | 35.3 | 37 | dBm | POUT = +2dBm / tone, 1MHz tone separation | 17 | |
| Output third order intercept point, Band 3p5 high power, VCC range | OIP3 | 33.3 | dBm | POUT = +2dBm / tone, VCC = 4.75V to 5.25V, TEPAD = -40°C to +115°C | 17 | ||
| Output 1dB compression point, Band 3p5 high power | OP1dB | 22.5 | 24 | dBm | 17 | ||
| Output 1dB compression point, Band 3p5 high power, VCC range | OP1dB | 21.5 | dBm | VCC = 4.75V to 5.25V, TEPAD = -40°C to +115°C | 17 | ||
| Noise figure, Band 4p7 low power | NF | 1.9 | dB | 18 | |||
| Output third order intercept point, Band 4p7 low power | OIP3 | 37 | dBm | POUT = +2dBm / tone, 1MHz tone separation | 18 | ||
| Output 1dB compression point, Band 4p7 low power | OP1dB | 24.5 | dBm | 18 | |||
| Noise figure, Band 4p7 high power | NF | 1.9 | dB | 19 | |||
| Output third order intercept point, Band 4p7 high power | OIP3 | 42.1 | dBm | POUT = +2dBm / tone, 1MHz tone separation | 19 | ||
| Output 1dB compression point, Band 4p7 high power | OP1dB | 25.1 | dBm | 19 | |||
| Junction to ambient thermal resistance | θJA | 67.9 | °C/W | Junction to ambient | 20 | ||
| Junction to case thermal resistance | θJC_BOT | 22.9 | °C/W | Case defined as the exposed paddle | 20 |
CAD (KiCad official)
- Symbol:
F1478NLGA8 - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
f1478nlga8-etched.step/f1478nlga8-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f1478nlga8.step/f1478nlga8.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (49 pp, sha256
34f1b35d4eb8c0a6, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).