3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLM5176RHFR
Texas Instruments · DC-DC Controllers · QFN-28-EP(4x5)
LM5176RHFR from Texas Instruments, in a QFN-28-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MODE | input | Current limit hiccup mode selection; 93.1 kΩ to AGND enables hiccup, 200 kΩ or VCC connection disables hiccup. |
| 2 | DITH | input | Frequency dithering enable; external capacitor to AGND modulates oscillator frequency by ±10% for EMI reduction. |
| 3 | RT/SYNC | input | Switching frequency programming pin; external resistor to AGND sets frequency (100-600 kHz) or accepts external clock signal. |
| 4 | SLOPE | input | Slope compensation ramp capacitor connection to AGND; provides ramp for stable current mode operation in buck and boost modes. |
| 5 | SS | input | Soft-start capacitor connection to AGND; capacitor programs soft-start time for gradual VCC and output regulation. |
| 6 | COMP | output | Error amplifier output (0.3 V to 3.0 V range); connect RC compensation network to AGND for feedback loop stability. |
| 7 | AGND | power_in | Analog ground of the IC; reference for all analog circuitry and also accepts PowerPAD solder connection for improved dissipation. |
| 8 | FB | input | Feedback pin for output voltage regulation; connect resistor divider from converter output (0.8 V VREF nominal). |
| 9 | VOSNS | input | Output voltage sense input; monitors power stage output voltage over 0.8-55 V range. |
| 10 | ISNS(-) | input | Current sense amplifier negative input; current sense resistor can locate on input or output side of converter. |
| 11 | ISNS(+) | input | Current sense amplifier positive input; when voltage reaches 50 mV, slow constant current control loop activates for regulation. |
| 12 | CSG | input | PWM current sense amplifier ground reference; connect directly to low-side of current sense resistor. |
| 13 | CS | input | Positive input to PWM current sense amplifier; implements cycle-by-cycle current limiting. |
| 14 | PGOOD | output | Power-good open-drain output (typical 4.2 mA sink); pulled low when FB voltage deviates outside ±9%/+10% of 0.8 V nominal. |
| 15 | SW2 | input | Boost side switching node; external bootstrap capacitor (0.1-0.22 µF ceramic) connects between SW2 and BOOT2. |
| 16 | HDRV2 | output | High-side gate driver output for boost switch; capable of sourcing 1.8 A and sinking 2.2 A peak current to MOSFET gate. |
| 17 | BOOT2 | power_out | Bootstrap power supply connection; external capacitor (0.1-0.22 µF ceramic) required between BOOT2 and SW2 to power HDRV2. |
| 18 | LDRV2 | output | Low-side gate driver output for boost switch; capable of sourcing 1.8 A and sinking 2.2 A peak current from VCC. |
| 19 | PGND | power_in | Power ground of the IC; provides high current ground connection for low-side gate drivers. |
| 20 | VCC | power_out | Internal bias regulator output; connect 0.1 µF capacitor to PGND or accept external 8-36 V supply via BIAS pin when VBIAS > 8 V. |
| 21 | BIAS | power_in | Optional external bias supply input (8-36 V); reduces IC power loss at high VIN when VBIAS exceeds 8 V threshold. |
| 22 | LDRV1 | output | Low-side gate driver output for buck switch; capable of sourcing 1.8 A and sinking 2.2 A peak current from VCC. |
| 23 | BOOT1 | power_out | Bootstrap power supply connection; external capacitor (0.1-0.22 µF ceramic) required between BOOT1 and SW1 to power HDRV1. |
| 24 | HDRV1 | output | High-side gate driver output for buck switch; capable of sourcing 1.8 A and sinking 2.2 A peak current to MOSFET gate. |
| 25 | SW1 | input | Buck side switching node; external bootstrap capacitor (0.1-0.22 µF ceramic) connects between SW1 and BOOT1. |
| 26 | EN/UVLO | input | Enable and under-voltage lockout input; below 0.4 V enters shutdown, above 1.22 V enables PWM if VCC exceeds UV threshold. |
| 27 | VIN | power_in | Input supply voltage pin; accepts 4.2-55 V nominal (maximum 60 V transient); 2.5-55 V with external BIAS ≥ 5 V. |
| 28 | VISNS | input | Input voltage sense pin; monitors power stage input rail voltage, valid 2.5-55 V range with VBIAS ≥ 5 V or VIN ≥ 4.5 V. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFN-28-EP(4x5) |
| Category | Power Supply Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Regulation voltage | VVCC(VIN) | 6.95 | 7.35 | 7.88 | V | VBIAS = 0 V, VCC open | 6 |
| VCC undervoltage lockout | VUV(VCC) | 3.11 | 3.27 | 3.43 | V | VCC increasing | 6 |
| VIN shutdown current | IQ | 2.6 | 10 | µA | VEN/UVLO = 0 V | 6 | |
| VIN operating current | 2 | 4 | mA | VEN/UVLO = 2 V, VFB = 0.9 V | 6 | ||
| VCC regulator output impedance | ROUT(VCC) | 8 | 16 | Ω | IVCC = 30 mA, VIN = 4 V | 6 | |
| BIAS switchover voltage | VBIAS(SW) | 7.25 | 8 | 8.75 | V | VIN = 24 V | 6 |
| Standby threshold | VEN(STBY) | 0.55 | 0.82 | 0.97 | V | EN/UVLO rising | 6 |
| Standby source current | IEN(STBY) | 1 | 2 | 3 | µA | VEN/UVLO = 1.1 V | 6 |
| Operating threshold | VEN(OP) | 1.17 | 1.22 | 1.29 | V | EN/UVLO rising | 6 |
| Operating hysteresis current | ΔIHYS(OP) | 2.15 | 3.15 | 4.25 | µA | VEN/UVLO = 1.5 V | 6 |
| Soft-start pullup current | ISS | 3.75 | 5 | 6.35 | µA | VSS = 0 V | 6 |
| Feedback reference voltage | VREF | 0.788 | 0.8 | 0.812 | V | FB = COMP | 6 |
| Switching frequency 1 | fSW(1) | 175 | 200 | 225 | kHz | RT = 40 kΩ | 6 |
| Switching frequency 2 | fSW(2) | 350 | 390 | 430 | kHz | RT = 20 kΩ | 6 |
| Buck current limit threshold (Valley, QFN-28) | VCS(BUCK) | 60 | 80 | 94 | mV | VIN = VVISNS = 24 V, VVOSNS = 12 V, VSLOPE = 0 V | 7 |
| Boost current limit threshold (Peak, QFN-28) | VCS(BOOST) | 96 | 120 | 140 | mV | VIN = VVISNS = 12 V, VVOSNS = 18 V, VSLOPE = 0 V | 7 |
| Average current loop regulation target | VSNS | 43 | 50 | 57 | mV | VISNS(-) = 24 V, sweep ISNS(+), VSS = 0.8 V | 7 |
| Buck adaptive slope current | ISLOPE | 24 | 30 | 35 | µA | VIN = VVISNS = 24 V, VVOSNS = 12 V, VSLOPE = 0 V | 7 |
| Boost adaptive slope current | ISLOPE | 13 | 17 | 21 | µA | VIN = VVISNS = 12 V, VVOSNS = 18 V, VSLOPE = 0 V | 7 |
| Source current out of MODE pin | IMODE | 17 | 20 | 23 | µA | 7 | |
| CCM with hiccup threshold | VCCM_HIC | 1.18 | 1.28 | 1.38 | V | 7 | |
| CCM no hiccup threshold | VCCM | 2.22 | 2.4 | 2.6 | V | 7 | |
| PGOOD trip threshold for falling FB | VPGD | -9 | % | Measured with respect to VREF | 8 | ||
| PGOOD trip threshold for rising FB | VPGD | 10 | % | Measured with respect to VREF | 8 | ||
| PGOOD sink current | ISINK(PGD) | 2 | 4.2 | 6.5 | mA | VPGOOD = 0.4 V | 8 |
| VIN, EN/UVLO, VISNS, VOSNS, ISNS(+), ISNS(–) absolute maximum | -0.3 | 60 | V | 5 | |||
| BIAS absolute maximum | -0.3 | 40 | V | 5 | |||
| FB, SS, DITH, RT/SYNC, SLOPE, COMP absolute maximum | -0.3 | 3.6 | V | 5 | |||
| SW1, SW2 absolute maximum | -1 | 60 | V | 5 | |||
| SW1, SW2 absolute maximum (transient) | -5 | 65 | V | 20 ns transient | 5 | ||
| VCC, MODE, PGOOD absolute maximum | -0.3 | 8.5 | V | 5 | |||
| LDRV1, LDRV2 absolute maximum | -0.3 | 8.5 | V | 5 | |||
| BOOT1, HDRV1 with respect to SW1 absolute maximum | -0.3 | 8.5 | V | 5 | |||
| BOOT2, HDRV2 with respect to SW2 absolute maximum | -0.3 | 8.5 | V | 5 | |||
| BOOT1, BOOT2 absolute maximum | -0.3 | 68 | V | 5 | |||
| ISNS(+) with respect to ISNS(-) absolute maximum | -0.3 | 0.3 | V | 5 | |||
| CS, CSG absolute maximum | -0.3 | 0.3 | V | 5 | |||
| Operating junction temperature absolute maximum | -40 | 150 | °C | 5 | |||
| Storage temperature absolute maximum | Tstg | -65 | 150 | °C | 5 | ||
| Input bias voltage (recommended) | VIN | 4.2 | 55 | V | 5 | ||
| Input power stage voltage with external bias (recommended) | VISNS | 2.5 | 55 | V | BIAS ≥ 5 V or VIN ≥ 4.5 V | 5 | |
| Bias supply voltage (when VCC in regulation) | BIAS | 8 | 36 | V | 5 | ||
| Output voltage range (recommended) | VOSNS | 0.8 | 55 | V | 5 | ||
| Enable voltage range (recommended) | EN/UVLO | 0 | 55 | V | 5 | ||
| Average current sense common mode range (recommended) | ISNS(+), ISNS(–) | 0 | 55 | V | 5 | ||
| Operating temperature (recommended) | TJ | -40 | 125 | °C | 5 | ||
| Operating frequency (recommended) | fsw | 100 | 600 | kHz | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 34.7 | °C/W | RHF (QFN) package | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 26.6 | °C/W | RHF (QFN) package | 6 | ||
| Junction-to-board thermal resistance | RθJB | 6.3 | °C/W | RHF (QFN) package | 6 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 2 | °C/W | RHF (QFN) package | 6 |
CAD (KiCad official)
- Symbol:
LM5176RHFR - Footprint:
Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: QFN-28-EP(4x5) (KiCad packages3D, STEP)
- 3D model files:
lm5176rhfr-etched.step/lm5176rhfr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lm5176rhfr.step/lm5176rhfr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (46 pp, sha256
4ce39346e67c6561, retrieved 2026-10-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).