component
XL224-TS
Public Made by Adomby adom
XINLUDA Operational Amplifier, TSSOP-14. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownXL224-TS
XINLUDA · Operational Amplifier · TSSOP-14
XL224-TS from XINLUDA, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | Out 1 | output | Output of amplifier 1; the output voltage range includes the negative supply, and outputs are short-circuit protected. |
| 2 | 1IN- | input | Inverting (negative) input of amplifier 1, a true differential input stage with ESD clamps. |
| 3 | 1IN+ | input | Non-inverting (positive) input of amplifier 1; the common-mode range extends to the negative supply, and either input can go to +32 V without damage. |
| 4 | VCC | power_in | Positive (maximum) power supply; single-supply operation is specified from 3.0 V to 32 V, with a 32 V absolute maximum. |
| 5 | 2IN+ | input | Non-inverting (positive) input of amplifier 2; the common-mode range extends to the negative supply, and either input can go to +32 V without damage. |
| 6 | 2IN- | input | Inverting (negative) input of amplifier 2, a true differential input stage with ESD clamps. |
| 7 | Out 2 | output | Output of amplifier 2; the output voltage range includes the negative supply, and outputs are short-circuit protected. |
| 8 | Out 3 | output | Output of amplifier 3; the output voltage range includes the negative supply, and outputs are short-circuit protected. |
| 9 | 3IN- | input | Inverting (negative) input of amplifier 3, a true differential input stage with ESD clamps. |
| 10 | 3IN+ | input | Non-inverting (positive) input of amplifier 3; the common-mode range extends to the negative supply, and either input can go to +32 V without damage. |
| 11 | VEE,GND | power_in | Negative (lowest) power supply or ground for single-supply operation; the common-mode range extends to this pin. |
| 12 | 4IN+ | input | Non-inverting (positive) input of amplifier 4; the common-mode range extends to the negative supply, and either input can go to +32 V without damage. |
| 13 | 4IN- | input | Inverting (negative) input of amplifier 4, a true differential input stage with ESD clamps. |
| 14 | Out 4 | output | Output of amplifier 4; the output voltage range includes the negative supply, and outputs are short-circuit protected. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | XINLUDA |
| Package | TSSOP-14 |
| Category | Amplifiers/Comparators |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input offset voltage | VIO | 2 | 5 | mV | VCC = 5.0 V to 30 V; VICR = 0 V to VCC -1.7 V, VO = 1.4 V, RS = 0 Ω; TA = 25C | 5 | |
| Input offset voltage (TA = Thigh) | VIO | 7 | mV | VCC = 5.0 V to 30 V; VICR = 0 V to VCC -1.7 V, VO = 1.4 V, RS = 0 Ω; TA = Thigh (Note 4) | 5 | ||
| Input offset voltage (TA = Tlow) | VIO | 7 | mV | VCC = 5.0 V to 30 V; VICR = 0 V to VCC -1.7 V, VO = 1.4 V, RS = 0 Ω; TA = Tlow (Note 4) | 5 | ||
| Input offset current | IIO | 3 | 30 | nA | VCC = 5 V, VEE = GND, TA = 25 °C (table default) | 5 | |
| Input offset current (TA = Thigh to Tlow) | IIO | 100 | nA | TA = Thigh to Tlow (Note 4) | 5 | ||
| Input bias current | IIB | -90 | -150 | nA | VCC = 5 V, VEE = GND, TA = 25 °C (table default) | 5 | |
| Input bias current (TA = Thigh to Tlow) | IIB | -300 | nA | TA = Thigh to Tlow (Note 4) | 5 | ||
| Input common mode voltage range | VICR | 0 | 28.3 | V | VCC = 30 V, TA = +25C | 5 | |
| Input common mode voltage range (TA = Thigh to Tlow) | VICR | 0 | 28 | V | VCC = 30 V, TA = Thigh to Tlow (Note 4) | 5 | |
| Large signal open loop voltage gain | AVOL | 50 | 100 | V/mV | RL = 2.0 kΩ, VCC = 15 V, for large VO swing | 5 | |
| Large signal open loop voltage gain (TA = Thigh to Tlow) | AVOL | 25 | V/mV | RL = 2.0 kΩ, VCC = 15 V, for large VO swing; TA = Thigh to Tlow (Note 4) | 5 | ||
| Common mode rejection | CMR | 70 | 85 | dB | RS ≤ 10 kΩ | 5 | |
| Power supply rejection | PSR | 65 | 100 | dB | 5 | ||
| Output voltage high limit | VOH | 3.3 | 3.5 | V | VCC = 5.0 V, RL = 2.0 kΩ, TA = 25C | 6 | |
| Output voltage high limit | VOH | 26 | V | VCC = 30 V, RL = 2.0 kΩ (TA = Thigh to Tlow, Note 7) | 6 | ||
| Output voltage high limit | VOH | 27 | 28 | V | VCC = 30 V, RL = 10 kΩ (TA = Thigh to Tlow, Note 7) | 6 | |
| Output voltage low limit | VOL | 5 | 20 | mV | VCC = 5.0 V, RL = 10 kΩ, TA = Thigh to Tlow (Note 7) | 6 | |
| Output source current | IO+ | 20 | 40 | mA | VID = +1.0 V, VCC = 15 V, TA = 25C | 6 | |
| Output source current (TA = Thigh to Tlow) | IO+ | 10 | 20 | mA | VID = +1.0 V, VCC = 15 V, TA = Thigh to Tlow (Note 7) | 6 | |
| Output sink current | IO- | 10 | 20 | mA | VID = -1.0 V, VCC = 15 V, TA = 25C | 6 | |
| Output sink current (TA = Thigh to Tlow) | IO- | 5 | 8 | mA | VID = -1.0 V, VCC = 15 V, TA = Thigh to Tlow (Note 7) | 6 | |
| Output sink current | IO- | 12 | 50 | µA | VID = -1.0 V, VO = 200 mV, TA = 25C | 6 | |
| Output short circuit to ground | ISC | 40 | 60 | mA | 6 | ||
| Power supply current | ICC | 3 | mA | VCC = 30 V, VO = 0 V, RL = (symbol garbled in extraction), TA = Thigh to Tlow (Note 7) | 6 | ||
| Power supply current | ICC | 1.2 | mA | VCC = 5.0 V, VO = 0 V, RL = (symbol garbled in extraction), TA = Thigh to Tlow (Note 7) | 6 | ||
| Power supply voltage, single supply | VCC | 32 | Vdc | Single supply | 4 | ||
| Power supply voltage, split supplies | VCC, VEE | 16 | Vdc | Split supplies | 4 | ||
| Differential input voltage range | VIDR | 32 | Vdc | Note 1 | 4 | ||
| Input common mode voltage range | VICR | -0.3 | 32 | Vdc | Note 2 | 4 | |
| Junction temperature | TJ | 150 | °C | 4 | |||
| Thermal resistance, junction to air (TSSOP14, Case 948G) | RθJA | 190 | C/W | Note 3, evaluation board with 1 oz copper, minimum pad size | 4 | ||
| Storage temperature range | Tstg | -50 | 150 | °C | 4 | ||
| ESD protection at any pin, human body model | Vesd | 2000 | V | Human body model | 4 | ||
| ESD protection at any pin, machine model | Vesd | 200 | V | Machine model | 4 | ||
| Operating ambient temperature range | TA | -25 | 85 | °C | XL/XD224, XL224-TS (Table 5.1); Ordering table lists -40 to +85 for XL224-TS | 4 | |
| Single supply operating voltage | VCC | 3 | 32 | V | Single supply operation (Features) | 1 | |
| Input offset voltage temperature coefficient | ΔVIO/ΔT | 7 | µV/C | TA = Thigh to Tlow (Notes 4 and 6) | 5 | ||
| Input offset current temperature coefficient | ΔIIO/ΔT | 10 | pA/C | TA = Thigh to Tlow (Notes 4 and 6) | 5 | ||
| Channel separation | CS | -120 | dB | 10 kHz ≤ f ≤ 20 kHz, input referenced | 5 | ||
| Slew rate at unity gain | SR | 0.5 | V/µs | VCC = ±15 V, TA = 25°C; RL = 1 MΩ, CL = 30 pF, VI = ±10 V | 4 | ||
| Unity-gain bandwidth | B1 | 1.2 | MHz | VCC = ±15 V, TA = 25°C; RL = 1 MΩ, CL = 20 pF | 4 |
CAD (KiCad official)
- Symbol:
XL224-TS - Footprint:
Package_SO:TSSOP-14_4.4x5mm_P0.65mm - 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files:
xl224-ts-etched.step/xl224-ts-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);xl224-ts.step/xl224-ts.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: XINLUDA datasheet (14 pp, sha256
384a39e4ec7d0b3c, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).