3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLTC2487IDE#PBF
Analog Devices · Analog To Digital Converters (ADCs) · DFN-14-EP(3x4)
LTC2487IDE#PBF from Analog Devices, in a DFN-14-EP(3x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | fO | input | Frequency control digital input: tied to GND selects the internal 307.2kHz oscillator, and an external clock may override it to change the output rate and digital filter null. |
| 2 | CA0 | input | Three-state (LOW, HIGH, Floating) chip address control bit that sets the device's I2C address. |
| 3 | CA1 | input | Three-state (LOW, HIGH, Floating) chip address control bit that sets the device's I2C address. |
| 4 | SCL | input | I2C serial clock input; the LTC2487 acts only as a slave, and data is shifted into SDA on SCL rising edges. |
| 5 | SDA | bidirectional | I2C bidirectional serial data line, open drain in data output mode, requiring a pull-up to VCC, and high impedance during data input. |
| 6 | GND | power_in | Ground connection that must be tied to a common low impedance ground plane. |
| 7 | COM | input | Common negative input (IN-) for single-ended multiplexer configurations, with voltage between GND - 0.3V and VCC + 0.3V. |
| 8 | CH0 | input | Analog input programmable for single-ended or differential mode, with voltage between GND - 0.3V and VCC + 0.3V. |
| 9 | CH1 | input | Analog input programmable for single-ended or differential mode, with voltage between GND - 0.3V and VCC + 0.3V. |
| 10 | CH2 | input | Analog input programmable for single-ended or differential mode, with voltage between GND - 0.3V and VCC + 0.3V. |
| 11 | CH3 | input | Analog input programmable for single-ended or differential mode, with voltage between GND - 0.3V and VCC + 0.3V. |
| 12 | VCC | power_in | Positive supply rated 2.7V to 5.5V, bypassed to GND with a 10µF tantalum capacitor in parallel with a 0.1µF ceramic capacitor placed close to the part. |
| 13 | REF+ | input | Positive differential reference input, which may be anywhere between GND and VCC but must remain at least 0.1V more positive than REF-. |
| 14 | REF- | input | Negative differential reference input, which may be anywhere between GND and VCC and must stay at least 0.1V below REF+. |
| 15 | GND (Exposed Pad) | power_in | Exposed pad is ground and must be soldered to the PCB ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-14-EP(3x4) |
| Category | Data Converters |
| Pins | 15 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | 2.7 | 5.5 | V | Full operating temperature range | 5 | |
| Supply Voltage (absolute maximum) | VCC | -0.3 | 6 | V | All voltages with respect to GND | 2 | |
| Operating Temperature Range LTC2487I | -40 | 85 | °C | LTC2487I grade | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Analog Input Voltage (CH0 to CH3, COM) | -0.3 | V | Max printed as VCC + 0.3V | 2 | |||
| Digital Input Voltage | -0.3 | V | Max printed as VCC + 0.3V | 2 | |||
| Digital Output Voltage | -0.3 | V | Max printed as VCC + 0.3V | 2 | |||
| REF+, REF- Voltage | -0.3 | V | Max printed as VCC + 0.3V | 2 | |||
| Maximum Junction Temperature | TJMAX | 125 | °C | 2 | |||
| Supply Current Conversion | ICC | 160 | 275 | µA | Conversion current (Note 11) | 5 | |
| Supply Current Temperature Measurement | ICC | 200 | 300 | µA | Temperature measurement (Note 11) | 5 | |
| Supply Current Sleep Mode | ICC | 1 | 2 | µA | Sleep mode (Note 11) | 5 | |
| External Oscillator Frequency Range | fEOSC | 10 | 1000 | kHz | Note 16 | 5 | |
| External Oscillator High Period | tHEO | 0.125 | 50 | µs | 5 | ||
| External Oscillator Low Period | tLEO | 0.125 | 50 | µs | 5 | ||
| Conversion Time for 1x Speed Mode 50Hz Mode | tCONV_1 | 157.2 | 160.3 | 163.5 | ms | 1x speed, 50Hz mode, internal oscillator | 5 |
| Conversion Time for 1x Speed Mode 60Hz Mode | tCONV_1 | 131 | 133.6 | 136.3 | ms | 1x speed, 60Hz mode, internal oscillator | 5 |
| Conversion Time for 1x Speed Mode Simultaneous 50Hz/60Hz | tCONV_1 | 144.1 | 146.9 | 149.9 | ms | 1x speed, simultaneous 50Hz/60Hz mode | 5 |
| Conversion Time for 2x Speed Mode 50Hz Mode | tCONV_2 | 78.7 | 80.3 | 81.9 | ms | 2x speed, 50Hz mode, internal oscillator | 5 |
| Conversion Time for 2x Speed Mode 60Hz Mode | tCONV_2 | 65.6 | 66.9 | 68.2 | ms | 2x speed, 60Hz mode, internal oscillator | 5 |
| Conversion Time for 2x Speed Mode Simultaneous 50Hz/60Hz | tCONV_2 | 72.2 | 73.6 | 75.1 | ms | 2x speed, simultaneous 50Hz/60Hz mode | 5 |
| SCL Clock Frequency | fSCL | 0 | 400 | kHz | 5 | ||
| Hold Time (Repeated) Start Condition | tHD(STA) | 0.6 | µs | 5 | |||
| Low Period of the SCL Pin | tLOW | 1.3 | µs | 5 | |||
| High Period of the SCL Pin | tHIGH | 0.6 | µs | 5 | |||
| Set-Up Time for a Repeated Start Condition | tSU(STA) | 0.6 | µs | 5 | |||
| Data Hold Time | tHD(DAT) | 0 | 0.9 | µs | 5 | ||
| Data Set-Up Time | tSU(DAT) | 100 | ns | 5 | |||
| Set-Up Time for Stop Condition | tSU(STO) | 0.6 | µs | 5 | |||
| Integral Nonlinearity | INL | 2 | ppm of VREF | 1x speed, 5V≤VCC≤5.5V, VREF=5V, VIN(CM)=2.5V (Note 6) | 3 | ||
| Integral Nonlinearity | INL | 1 | ppm of VREF | 1x speed, 2.7V≤VCC≤5.5V, VREF=2.5V, VIN(CM)=1.25V (Note 6) | 3 | ||
| Offset Error | 0.5 | 5 | µV | 1x speed, 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Note 13) | 3 | ||
| Positive Full-Scale Error | 32 | ppm of VREF | 1x speed, 2.5V≤VREF≤VCC, IN+=0.75VREF, IN-=0.25VREF | 3 | |||
| Negative Full-Scale Error | 32 | ppm of VREF | 1x speed, 2.5V≤VREF≤VCC, IN+=0.25VREF, IN-=0.75VREF | 3 | |||
| Total Unadjusted Error | 15 | ppm of VREF | 5V≤VCC≤5.5V, VREF=2.5V, VIN(CM)=1.25V | 3 | |||
| Internal PTAT Signal | 27.8 | 28 | 28.2 | mV | TA=27°C (Note 13) | 3 | |
| Programmable Gain (1x speed) | 1 | 256 | 1x speed | 3 | |||
| Offset Error (2x speed) | 0.2 | 2 | mV | 2x speed, 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Note 13) | 3 | ||
| Programmable Gain (2x speed) | 1 | 128 | 2x speed | 3 | |||
| Input Common Mode Rejection DC | 140 | dB | 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Note 5) | 3 | |||
| Input Common Mode Rejection 50Hz ±2% | 140 | dB | 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Notes 5, 7) | 3 | |||
| Input Common Mode Rejection 60Hz ±2% | 140 | dB | 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Notes 5, 8) | 3 | |||
| Input Normal Mode Rejection 50Hz ±2% | 110 | 120 | dB | 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Notes 5, 7) | 3 | ||
| Input Normal Mode Rejection 60Hz ±2% | 110 | 120 | dB | 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Notes 5, 8) | 3 | ||
| Input Normal Mode Rejection 50Hz/60Hz ±2% | 87 | dB | 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Notes 5, 9) | 3 | |||
| Reference Common Mode Rejection DC | 120 | 140 | dB | 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Note 5) | 3 | ||
| IN+ DC Leakage Current | IDC_LEAK(IN+) | -10 | 1 | 10 | nA | Sleep mode, IN+ = GND | 4 |
| IN- DC Leakage Current | IDC_LEAK(IN-) | -10 | 1 | 10 | nA | Sleep mode, IN- = GND | 4 |
| REF+ DC Leakage Current | IDC_LEAK(REF+) | -100 | 1 | 100 | nA | Sleep mode, REF+ = VCC | 4 |
| REF- DC Leakage Current | IDC_LEAK(REF-) | -100 | 1 | 100 | nA | Sleep mode, REF- = GND | 4 |
| Low Level Output Voltage (SDA) | VOL | 0.4 | V | I = 3mA | 4 | ||
| Input Leakage | IIN | 1 | µA | 0.1VCC ≤ VIN ≤ VCC | 4 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 37 | °C/W | 2 | |||
| Offset Error Drift | 10 | nV/°C | 1x speed, 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC | 3 | |||
| Positive Full-Scale Error Drift | 0.1 | ppm of VREF/°C | 1x speed, 2.5V≤VREF≤VCC, IN+=0.75VREF, IN-=0.25VREF | 3 | |||
| Negative Full-Scale Error Drift | 0.1 | ppm of VREF/°C | 1x speed, 2.5V≤VREF≤VCC, IN+=0.25VREF, IN-=0.75VREF | 3 | |||
| Output Noise | 0.6 | µVRMS | 1x speed, 2.7V<VCC<5.5V, 2.5V≤VREF≤VCC, GND≤IN+=IN-≤VCC (Note 12) | 3 | |||
| Internal PTAT Temperature Coefficient | 93.5 | µV/°C | 3 |
CAD (KiCad official)
- Symbol:
LTC2487IDE#PBF - Footprint:
Package_DFN_QFN:DFN-14-1EP_3x4mm_P0.5mm_EP1.7x3.3mm - 3D model: DFN-14-EP(3x4) (KiCad packages3D, STEP)
- 3D model files:
ltc2487ide-pbf-etched.step/ltc2487ide-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc2487ide-pbf.step/ltc2487ide-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (34 pp, sha256
d6ef6dd097c73ec1, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).