3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSHT45-AD1F-R2
Sensirion · Global Sourcing Parts · DFN-4
SHT45-AD1F-R2 from Sensirion, in a DFN-4. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDA | bidirectional | Serial data line for the I2C interface, bidirectional. |
| 2 | SCL | input | Serial clock line for the I2C interface, unidirectional input. |
| 3 | VDD | power_in | Supply voltage; the datasheet specifies VDD = 1.08 V … 3.6 V. |
| 4 | VSS | power_in | Ground reference for the sensor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sensirion |
| Package | DFN-4 |
| Category | Global Sourcing Parts |
| Pins | 4 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VDD | 1.08 | 3.3 | 3.6 | V | - | 9 |
| Power-up/down level (static power supply) | VPOR | 0.6 | 1.08 | V | Static power supply | 9 | |
| Slew rate of the supply voltage | VDD, slew | 20 | V/ms | Voltage changes between VDD, min and VDD, max | 9 | ||
| Supply current, heater off, idle state | IDD | 0.08 | 1 | µA | Idle state, at 25 °C | 9 | |
| Supply current, heater off, idle state | IDD | 3.4 | µA | Idle state, at 125 °C | 9 | ||
| Supply current, measurement | IDD | 320 | 500 | µA | Current while sensor is measuring | 9 | |
| Supply current, heater on | IDD | 60 | 100 | mA | Nomin. heater "200 mW" | 9 | |
| Supply current, heater on | IDD | 33 | 55 | mA | Nomin. heater "110 mW" | 9 | |
| Supply current, heater on | IDD | 6 | 10 | mA | Nomin. heater "20 mW" | 9 | |
| Low level input voltage | VIL | 0 | V | - | 9 | ||
| Pull-up resistor | Rp | 820 | Ω | VDD < 1.62 V | 9 | ||
| Pull-up resistor | Rp | 390 | Ω | VDD ≥ 1.62 V | 9 | ||
| Low level output voltage | VOL | 0.4 | V | VDD > 2.0 V, Rpullup > 390 Ω | 9 | ||
| Capacitive bus load | Cb | 400 | pF | RP ≤ 820 Ω: fast mode | 9 | ||
| Capacitive bus load | Cb | 340 | pF | Rp = 390 Ω, VDD > 1.62 V: fast mode plus | 9 | ||
| Power-up time | tPU | 0.3 | 1 | ms | After hard reset, VDD ≥ VPOR | 10 | |
| Soft reset time | tSR | 1 | ms | After soft reset | 10 | ||
| Measurement duration, low repeatability | tMEAS,l | 1.3 | 1.6 | ms | Low repeatability | 10 | |
| Measurement duration, medium repeatability | tMEAS,m | 3.7 | 4.5 | ms | Med. repeatability | 10 | |
| Measurement duration, high repeatability | tMEAS,h | 6.9 | 8.3 | ms | High repeatability | 10 | |
| Heater-on duration, long pulse | tHeater | 0.9 | 1 | 1.1 | s | Long pulse | 10 |
| Heater-on duration, short pulse | tHeater | 0.09 | 0.1 | 0.11 | s | Short pulse | 10 |
| Max voltage on any pin | -0.3 | V | Referenced to VSS; upper limit is VDD +0.3 V | 10 | |||
| Operating temperature range | -40 | 125 | °C | - | 10 | ||
| Storage temperature range | -40 | 150 | °C | - | 10 | ||
| ESD HBM | 2 | kV | - | 10 | |||
| ESD CDM | 500 | V | - | 10 | |||
| Latch up | 100 | mA | JESD78 Class II, 125 °C | 10 | |||
| Recommended normal temperature range | 5 | 60 | °C | Recommended normal temperature and humidity range | 7 | ||
| Recommended normal humidity range | 20 | 80 | %RH | Recommended normal temperature and humidity range | 7 | ||
| Specified relative humidity range | 0 | 100 | %RH | Extended range | 4 | ||
| Specified temperature range | -40 | 125 | °C | - | 6 | ||
| Junction-to-ambient thermal resistance RθJA | RθJA | 246 | K/W | Heater off, die pad soldered | 16 | ||
| Junction-to-ambient thermal resistance RθJA | RθJA | 308 | K/W | Heater on, die pad soldered | 16 | ||
| Junction-to-ambient thermal resistance RθJA | RθJA | 297 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-ambient thermal resistance RθJA | RθJA | 357 | K/W | Heater on, die pad not soldered | 16 | ||
| Junction-to-case thermal resistance RθJC | RθJC | 189 | K/W | Heater off, die pad soldered | 16 | ||
| Junction-to-case thermal resistance RθJC | RθJC | 255 | K/W | Heater on, die pad soldered | 16 | ||
| Junction-to-case thermal resistance RθJC | RθJC | 191 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-case thermal resistance RθJC | RθJC | 257 | K/W | Heater on, die pad not soldered | 16 | ||
| Junction-to-board thermal resistance RθJB | RθJB | 159 | K/W | Heater off, die pad soldered | 16 | ||
| Junction-to-board thermal resistance RθJB | RθJB | 225 | K/W | Heater on, die pad soldered | 16 | ||
| Junction-to-board thermal resistance RθJB | RθJB | 193 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-board thermal resistance RθJB | RθJB | 258 | K/W | Heater on, die pad not soldered | 16 | ||
| Junction-to-board characterization parameter ΨJB | ΨJB | 159 | K/W | Heater off, die pad soldered | 16 | ||
| Junction-to-board characterization parameter ΨJB | ΨJB | 223 | K/W | Heater on, die pad soldered | 16 | ||
| Junction-to-board characterization parameter ΨJB | ΨJB | 191 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-board characterization parameter ΨJB | ΨJB | 254 | K/W | Heater on, die pad not soldered | 16 | ||
| Junction-to-top characterization parameter ΨJT | ΨJT | 38 | K/W | Heater off, die pad soldered | 16 | ||
| Junction-to-top characterization parameter ΨJT | ΨJT | 105 | K/W | Heater on, die pad soldered | 16 | ||
| Junction-to-top characterization parameter ΨJT | ΨJT | 44 | K/W | Heater off, die pad not soldered | 16 | ||
| Junction-to-top characterization parameter ΨJT | ΨJT | 112 | K/W | Heater on, die pad not soldered | 16 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | SHT4x is provided in an open-cavity dual flat no lead (DFN) package. The humidity sensor opening is centered on the top side of the package. The sensor chip is made of silicon, hosted on a copper | 14 |
CAD (KiCad official)
- Symbol:
SHT45-AD1F-R2 - Footprint:
Package_DFN_QFN:DFN-4_5x7mm_P5.08mm - 3D model: DFN-4, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.9 mm nominal QFN height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
sht45-ad1f-r2-etched.step/sht45-ad1f-r2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sht45-ad1f-r2.step/sht45-ad1f-r2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Sensirion datasheet (22 pp, sha256
6abf277de684fff3, retrieved 2026-11-08, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).