Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

R5F513T3AGFJ#30

RENESAS · Microcontrollers (MCU/MPU/SOC) · LQFP-32(7x7)

R5F513T3AGFJ#30 from RENESAS, in a LQFP-32(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VCL passive Connect this pin to the VSS pin via the 4.7 μF smoothing capacitor used to stabilize the internal power supply, placed close to the pin.
2 MD input Operating mode setting pin; the signal level on this pin must not be changed during operation (multiplexed with FINED, the FINE on-chip emulator interface I/O).
3 RES# input Reset pin; the MCU enters the reset state when this signal goes low, and it should be connected to VCC via a pull-up resistor when unused.
4 P37/XTAL output XTAL output pin for connecting a crystal to the main clock oscillator; the pin can alternatively be used as general I/O port P37 when the main clock is not used.
5 VSS power_in Ground pin; connect it to the system power supply (0 V).
6 P36/EXTAL input EXTAL input pin for the main clock oscillator, through which an external clock can be input; the pin can alternatively be used as general I/O port P36 when the main clock is not used.
7 VCC power_in Power supply pin; connect it to the system power supply.
8 PE2 input 1-bit input-only port pin that also serves as the NMI non-maskable interrupt request input and POE10# request input; connect it to VCC via a pull-up resistor when unused.
9 PB7 bidirectional General I/O port pin multiplexed with MTIOC3C/MTCLKD, SCI1/SCI5 serial signals and IRQ5; input pull-up, open-drain output and drive capacity switching are available.
10 PB6 bidirectional General I/O port pin multiplexed with MTIOC1B/MTIOC3A and SCI1/SCI5 transmit signals; fixed to high drive output and 5-V tolerant with input pull-up and open-drain output available.
11 PB3 bidirectional General I/O port pin multiplexed with MTIOC0A/CACREF and SCI5/SCI12 clock SCK5/SCK12; input pull-up, open-drain output and drive capacity switching are available.
12 PB2 bidirectional General I/O port pin multiplexed with MTIOC0B/MTCLKC/ADSM0, SCI5 transmit signals and SDA0; fixed to high drive output and 5-V tolerant.
13 PB1 bidirectional General I/O port pin multiplexed with MTIOC0C/MTIC5W/MTCLKA, SCI5 receive signals, SCL0 and IRQ2; fixed to high drive output and 5-V tolerant, with TTL input level when SCL is selected with SMBus in RIIC.
14 PB0 bidirectional General I/O port pin multiplexed with MTIOC0D/MTIOC2A/MTCLKB and SCI12 transmit signals; input pull-up, open-drain output and drive capacity switching are available.
15 P94 bidirectional General I/O port pin multiplexed with MTIOC2B/MTIC5U/MTCLKA, SCI12 receive signals and IRQ1; input pull-up, open-drain output and drive capacity switching are available.
16 P93 bidirectional General I/O port pin multiplexed with MTIOC1A/MTIC5V, SCI5/SCI12 clock SCK5/SCK12, IRQ0 and ADTRG0# A/D trigger input; input pull-up, open-drain output and drive capacity switching are available.
17 P76 bidirectional General I/O port pin multiplexed with MTIOC4D; fixed to high drive output and 5-V tolerant with input pull-up available.
18 P75 bidirectional General I/O port pin multiplexed with MTIOC4C; fixed to high drive output and 5-V tolerant with input pull-up available.
19 P74 bidirectional General I/O port pin multiplexed with MTIOC3D; fixed to high drive output and 5-V tolerant with input pull-up available.
20 P73 bidirectional General I/O port pin multiplexed with MTIOC4B; fixed to high drive output and 5-V tolerant with input pull-up available.
21 P72 bidirectional General I/O port pin multiplexed with MTIOC4A; fixed to high drive output and 5-V tolerant with input pull-up available.
22 P71 bidirectional General I/O port pin multiplexed with MTIOC3B; fixed to high drive output and 5-V tolerant with input pull-up available.
23 VCC power_in Power supply pin; connect it to the system power supply.
24 VSS power_in Ground pin; connect it to the system power supply (0 V).
25 P44 bidirectional General I/O port pin shared with analog input AN004 and comparator input CMPC12; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input.
26 P43 bidirectional General I/O port pin shared with analog input AN003 and comparator input CMPC02; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input.
27 P42 bidirectional General I/O port pin shared with analog input AN002 and comparator input CMPC20; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input.
28 P41 bidirectional General I/O port pin shared with analog input AN001 and comparator input CMPC10; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input.
29 P40 bidirectional General I/O port pin shared with analog input AN000 and comparator input CMPC00; its I/O buffer power source is AVCC0, and it must be set as a general input when used as an analog input.
30 AVCC0 power_in Analog voltage supply pin for the 12-bit A/D converter, comparator C and the 8-bit D/A converter; connect it to VCC when these modules are not used.
31 AVSS0 power_in Analog ground pin for the 12-bit A/D converter, comparator C and the 8-bit D/A converter; connect it to VSS when these modules are not used.
32 P11 bidirectional General I/O port pin multiplexed with MTIOC3A/MTCLKA/POE8#, IRQ1 and CVREFC0 comparator reference voltage input; input pull-up, open-drain output and drive capacity switching are available.

Key specifications

Parameter Value
Manufacturer RENESAS
Package LQFP-32(7x7)
Category Embedded Processors & Controllers
Pins 32

CAD (KiCad official)

  • Symbol: R5F513T3AGFJ#30
  • Footprint: Package_QFP:LQFP-32_7x7mm_P0.8mm
  • 3D model: LQFP-32(7x7) (KiCad packages3D, STEP)
  • 3D model files: r5f513t3agfj-30-etched.step / r5f513t3agfj-30-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); r5f513t3agfj-30.step / r5f513t3agfj-30.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (1055 pp, sha256 b57248feedc44923, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF