Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8582IDKD#TRPBF

Analog Devices · DC-DC Converters · DFN-24-EP(4x7)

LT8582IDKD#TRPBF from Analog Devices, in a DFN-24-EP(4x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SWA1 output Master NPN switch collector for channel 1, designed to handle a peak collector current of 1.7A minimum.
2 VIN1 power_in Channel 1 input supply pin that must be locally bypassed.
3 PG1 output Open-drain active-high power good output that requires a pull-up resistor and is valid only when SHDN is above 1.31V and VIN is above 2.3V.
4 GATE1 output Pull-down current source for an external PMOS gate with a maximum pull-down current of 1mA at SS voltages above 550mV.
5 VC1 passive Channel 1 error amplifier output pin to which the external compensation network is tied.
6 FBX1 input Channel 1 positive and negative feedback pin, regulated to a positive feedback voltage of 1.204V through a resistor to VOUT.
7 FBX2 input Channel 2 positive and negative feedback pin, regulated to a positive feedback voltage of 1.204V through a resistor to VOUT.
8 VC2 passive Channel 2 error amplifier output pin to which the external compensation network is tied.
9 GATE2 output Pull-down current source for an external PMOS gate with a maximum pull-down current of 1mA at SS voltages above 550mV.
10 PG2 output Open-drain active-high power good output that requires a pull-up resistor and is valid only when SHDN is above 1.31V and VIN is above 2.3V.
11 VIN2 power_in Channel 2 input supply pin that must be locally bypassed.
12 SWA2 output Master NPN switch collector for channel 2, designed to handle a peak collector current of 1.7A minimum.
13 SWB2 output Slave NPN switch collector for channel 2, designed to handle a peak collector current of 1.3A minimum.
14 CLKOUT2 output Clock output in phase with the internal oscillator or SYNC pin, intended to drive capacitive loads up to 120pF only.
15 SHDN2 input Channel 2 shutdown pin that must be driven below 0.3V to disable the channel and above 1.31V typical to activate it, and must not be floated.
16 RT2 passive Channel 2 timing resistor pin that sets a fixed free-running switching frequency and must not be floated.
17 SS2 passive Channel 2 soft-start pin charged by a nominal 250k resistor to about 2.1V at start-up, with a soft-start capacitor placed here.
18 SYNC2 input Channel 2 synchronization pin whose high level must exceed 1.3V and low level must be less than 0.4V.
19 SYNC1 input Channel 1 synchronization pin whose high level must exceed 1.3V and low level must be less than 0.4V.
20 SS1 passive Channel 1 soft-start pin charged by a nominal 250k resistor to about 2.1V at start-up, with a soft-start capacitor placed here.
21 RT1 passive Channel 1 timing resistor pin that sets a fixed free-running switching frequency and must not be floated.
22 SHDN1 input Channel 1 shutdown pin that must be driven below 0.3V to disable the channel and above 1.31V typical to activate it, and must not be floated.
23 CLKOUT1 output Clock output 180° out of phase with the internal oscillator or SYNC pin with fixed ~50% duty cycle, intended to drive capacitive loads up to 120pF only.
24 SWB1 output Slave NPN switch collector for channel 1, designed to handle a peak collector current of 1.3A minimum.
25 GND power_in Exposed pad ground that must be soldered directly to the local ground plane.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-24-EP(4x7)
Category Power Supply Chip
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN1 Voltage -0.3 40 V 2
SWA1/SWB1 Voltage -0.4 42 V 2
RT1 Voltage -0.3 5 V 2
SS1 Voltage -0.3 2.5 V 2
FBX1 Voltage -0.3 5 V 2
VC1 Voltage -0.3 2 V 2
SHDN1 Voltage 40 V 2
SHDN1 Current -1 mA 2
SYNC1 Voltage -0.3 5.5 V 2
GATE1 Voltage -0.3 60 V 2
PG1 Voltage -0.3 40 V 2
PG1 Current -0.5 0.5 mA 2
Operating Junction Temperature Range (LT8582I) -40 125 °C 2
Storage Temperature Range -65 150 °C 2
VIN Overvoltage Lockout 22.2 24.5 27 V 3
Positive Feedback Voltage 1.185 1.204 1.22 V 3
Negative Feedback Voltage 2 7 16 mV 3
Positive FBX Pin Bias Current 81 83.3 85 μA VFBX = Positive Feedback Voltage, Current into Pin 3
Negative FBX Pin Bias Current 81 83.3 85.5 μA VFBX = Negative Feedback Voltage, Current out of Pin 3
Switching Frequency fOSC 2.125 2.5 2.875 MHz RT = 31.6kΩ 3
Switching Frequency fOSC 170 200 230 kHz RT = 407kΩ 3
Switching Frequency Range 200 2500 kHz Free-Running or Synchronizing 3
SYNC High Level 1.3 V for Sync 3
SYNC Low Level 0.4 V for Sync 3
SYNC Clock Pulse Duty Cycle 20 80 % VSYNC = 0V to 2V 3
SWA Current Limit, Minimum Duty Cycle 1.8 2.4 3 A Minimum Duty Cycle 3
SWA Current Limit, Maximum Duty Cycle 1.3 1.8 2.5 A Maximum Duty Cycle 3
SWA FAULT Current Limit, Minimum Duty Cycle 2.2 2.8 3.5 A Minimum Duty Cycle 3
SWA FAULT Current Limit, Maximum Duty Cycle 1.6 2.3 3 A Maximum Duty Cycle 3
SWA + SWB Current Limit, Minimum Duty Cycle 3.3 4.3 5.4 A Minimum Duty Cycle, ISWB/ISWA = 0.79 3
SWA + SWB Current Limit, Maximum Duty Cycle 2.3 4.1 4.5 A Maximum Duty Cycle, ISWB/ISWA = 0.79 3
SWA + SWB FAULT Current Limit, Minimum Duty Cycle 4 5 6.3 A Minimum Duty Cycle, ISWB/ISWA = 0.79 3
SWA + SWB FAULT Current Limit, Maximum Duty Cycle 2.8 4 5.4 A Maximum Duty Cycle, ISWB/ISWA = 0.79 3
SS Charge Current 5.7 8.8 11.7 μA VSS = 30mV, Current Flows out of SS Pin 3
SS Discharge Current 5.7 8.8 11.7 μA Part in FAULT, VSS = 2.1V, Current Flows into SS Pin 3
SS High Detection Voltage 1.65 1.84 2 V Part in FAULT 3
SS Low Detection Voltage 15 55 100 mV Part Exiting FAULT 3
SHDN Minimum Input Voltage High 1.26 1.31 1.4 V Active Mode, SHDN Rising 3
SHDN Minimum Input Voltage High 1.21 1.27 1.35 V Active Mode, SHDN Falling 3
SHDN Input Voltage Low 0.3 V Shutdown Mode 3
PG Threshold for Positive Feedback Voltage 1.09 1.15 1.2 V VFBX Rising 4
PG Threshold for Negative Feedback Voltage 20 65 120 mV VFBX Falling 4
GATE Pull-Down Current 0.8 1 1.2 mA VGATE = 3V 4
CLKOUT Output Voltage High 1.9 2.1 2.3 V 1mA out of CLKOUT Pin 4
Switch VCESAT VCESAT 270 mV ISWA + ISWB = 2.75A 3
Minimum Off-Time 45 ns 3
Minimum On-Time 55 ns 3
CLKOUT1 Duty Cycle 50 % All TJ 4
Thermal Resistance Junction-to-Ambient θJA 34 °C/W 2
Thermal Resistance Junction-to-Case θJC 7 °C/W 2
Maximum Junction Temperature TJMAX 125 °C 2

CAD (KiCad official)

  • Symbol: LT8582IDKD#TRPBF
  • Footprint: Package_DFN_QFN:DFN-24-1EP_4x7mm_P0.5mm_EP2.64x6.44mm
  • 3D model: DFN-24-EP(4x7) (KiCad packages3D, STEP)
  • 3D model files: lt8582idkd-trpbf-etched.step / lt8582idkd-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8582idkd-trpbf.step / lt8582idkd-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (36 pp, sha256 d4cd3a1bf42e8ed8, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF