component
AP7366-W5-7
Public Made by Adomby adom
Diodes Incorporated Linear Voltage Regulators (LDO), SOT-25. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownAP7366-W5-7
Diodes Incorporated · Linear Voltage Regulators (LDO) · SOT-25
AP7366-W5-7 from Diodes Incorporated, in a SOT-25. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Voltage input pin, which should be bypassed to ground with at least a 1µF MLCC capacitor; the input range is 2.2V to 6V. |
| 2 | GND | power_in | Ground pin; the datasheet states no further electrical limits for this pin. |
| 3 | EN | input | Active-high enable input that turns the regulator on when driven above VIH (minimum 1.0V) and off below VIL (maximum 0.3V); it can be tied to IN for always-on operation. |
| 4 | ADJ | input | Output feedback pin that sets the output voltage from 0.8V to 5.0V through an external resistor divider referenced to the 0.8V internal reference, with R2 kept below 80kΩ. |
| 5 | OUT | power_out | Voltage output pin, which should be bypassed to ground with a 1µF MLCC capacitor and supplies up to 600mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Diodes Incorporated |
| Package | SOT-25 |
| Category | Power Management ICs |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 2.2 | 6 | V | 3 | ||
| Output Voltage | VOUT | 0.8 | 5 | V | 3 | ||
| Output Current | IOUT | 0 | 600 | mA | Note 4 | 3 | |
| Operating Ambient Temperature | TA | -40 | 85 | °C | 3 | ||
| Input Voltage | VIN | 6.5 | V | 3 | |||
| Human Body Model ESD Protection | ESD HBM | 2000 | V | 3 | |||
| Charged Device Model ESD Protection | ESD CDM | -1000 | 1000 | V | Charged Device Model | 3 | |
| Storage Temperature Range | TST | -65 | 150 | °C | 3 | ||
| Maximum Junction Temperature | TJ | 150 | °C | 3 | |||
| ADJ Reference Voltage (Adjustable Version) | VREF | 0.788 | 0.8 | 0.812 | V | IOUT = 10mA | 4 |
| ADJ Leakage (Adjustable Version) | IADJ | 0.1 | 0.5 | μA | 4 | ||
| Input Quiescent Current | IQ | 60 | 80 | μA | VEN = VIN, IOUT = 0mA | 4 | |
| Input Shutdown Current | ISHDN | -1 | 0.05 | 1 | μA | VEN = 0V, IOUT = 0mA | 4 |
| Line Regulation | VOUT/VIN/VOUT | 0.01 | 0.1 | %/V | VIN = (VOUT +1V) to 5.5V, IOUT = 10mA, TA = +25°C | 4 | |
| Line Regulation | VOUT/VIN/VOUT | 0.2 | %/V | VIN = (VOUT +1V) to 5.5V, IOUT = 10mA, -40°C ≦ TA ≦ +85°C | 4 | ||
| Load Regulation | VOUT/VOUT | -1 | 1 | % | IOUT = 1mA to 600mA, 1.2V < VOUT ≦ 3.9V | 4 | |
| Load Regulation | VOUT/VOUT | -1.5 | 1.5 | % | IOUT = 1mA to 600mA, 1.0V ≦ VOUT ≦ 1.2V | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 650 | 900 | mV | VOUT = 1.0V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 480 | 700 | mV | VOUT = 1.2V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 200 | 340 | mV | VOUT = 1.5V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 160 | 250 | mV | VOUT = 1.8V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 140 | 200 | mV | VOUT = 2.0V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 125 | 190 | mV | VOUT = 2.5V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 115 | 180 | mV | VOUT = 2.8V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 110 | 170 | mV | VOUT = 3.0V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 105 | 160 | mV | VOUT = 3.3V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 100 | 150 | mV | VOUT = 3.9V, IOUT = 300mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 850 | 1200 | mV | VOUT = 1.0V, IOUT = 600mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 800 | 1000 | mV | VOUT = 1.2V, IOUT = 600mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 450 | 700 | mV | VOUT = 1.5V, IOUT = 600mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 320 | 420 | mV | VOUT = 1.8V, IOUT = 600mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 285 | 400 | mV | VOUT = 2.0V, IOUT = 600mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 250 | 380 | mV | VOUT = 2.5V, IOUT = 600mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 230 | 350 | mV | VOUT = 2.8V, IOUT = 600mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 220 | 330 | mV | VOUT = 3.0V, IOUT = 600mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 210 | 320 | mV | VOUT = 3.3V, IOUT = 600mA | 4 | |
| Dropout Voltage (Note 5) | VDROPOUT | 190 | 290 | mV | VOUT = 3.9V, IOUT = 600mA | 4 | |
| Current Limit | ILIMIT | 0.66 | 1 | A | VIN = VOUT + 1V | 4 | |
| EN Input Logic-Low Voltage | VIL | 0.3 | V | VIN = VIN-Min to VIN-Max | 4 | ||
| EN Input Logic-High Voltage | VIH | 1 | V | VIN = VIN-Min to VIN-Max | 4 | ||
| EN Input Leakage Current | IEN | -0.1 | 0.1 | μA | VIN = 5.5V or VEN = 0V | 4 | |
| Output Voltage Temperature Coefficient | VOUT/TA/VOUT | -100 | 100 | ppm/°C | IOUT = 100mA, -40°C ≤ TA ≤ +85°C | 5 | |
| PSRR | PSRR | 75 | dB | f = 1kHz, IOUT = 100mA | 4 | ||
| PSRR | PSRR | 55 | dB | f = 10kHz, IOUT = 100mA | 4 | ||
| Short-Circuit Current | ISHORT | 250 | mA | VIN = VOUT + 1V, Output Voltage <15% of VOUT | 4 | ||
| Start-Up Time | tST | 150 | μs | VOUT = 0V to 3.0V, RL = 30Ω | 4 | ||
| Thermal Shutdown Threshold | TSHDN | 150 | °C | 4 | |||
| Thermal Shutdown Hysteresis | THYS | 20 | °C | 4 | |||
| EN Pulldown Resistor | RENPD | 3 | MΩ | 5 | |||
| Output Discharge Resistor | RPD | 100 | Ω | VOL = 1V | 5 | ||
| Thermal Resistance Junction-to-Ambient (SOT25) | JA | 169 | °C/W | SOT25 (Note 7) | 5 | ||
| Thermal Resistance Junction-to-Case (SOT25) | JC | 31 | °C/W | SOT25 (Note 7) | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | reduce noise. For PCB layout, a wide copper trace is required for both IN and GND pins. A lower ESR capacitor type allows the use of less | 8 |
CAD (KiCad official)
- Symbol:
AP7366-W5-7 - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-25, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.1 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
ap7366-w5-7-etched.step/ap7366-w5-7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ap7366-w5-7.step/ap7366-w5-7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Diodes Incorporated datasheet (15 pp, sha256
e18fe72219e65037, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).