Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

F280049PZQ

Texas Instruments · Pre-ordered MCUs · TQFP-100(14x14)

F280049PZQ from Texas Instruments, in a TQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GPIO28 bidirectional General-purpose I/O 28 with SCIA_RX, EPWM7_A, EQEP1_A, SD1_D3 and ERRORSTS alternate functions per the GPIO mux table.
2 XRSn bidirectional Device reset input and watchdog reset output; open-drain with internal pull-up, and an external 2.2kΩ to 10kΩ resistor to VDDIO is required.
3 VDDIO power_in 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF on each VDDIO pin.
4 VDD power_in 1.2V digital logic supply pin; place at least about 20µF total decoupling capacitance on the VDD pins.
5 VSS power_in Digital ground pin that must be connected to the board ground.
6 A6/PGA5_OF input ADC-A input 6 (also PGA-5 output filter and CMPSS-5 comparator input); analog pin, not a digital I/O by default.
7 B2/C6/PGA3_OF input ADC-B input 2 (also ADC-C input 6 and PGA-3 output filter); analog pin.
8 B3/VDAC input ADC-B input 3 shared with the optional external DAC reference VDAC; a 100pF capacitor to VSSA is fixed on this pin and a 1µF capacitor is needed when used as the DAC reference.
9 A2/B6/PGA1_OF input ADC-A input 2 (also ADC-B input 6 and PGA-1 output filter); analog pin.
10 A3 input ADC-A input 3 with CMPSS-1 comparator inputs and a digital input AIO233.
11 VDDA power_in 3.3V analog supply pin; place a decoupling capacitor of at least 2.2µF to VSSA on each VDDA pin.
12 VSSA power_in Analog ground pin.
13 PGA5_GND power_in Kelvin ground reference for PGA-5 input.
14 PGA1_GND power_in Kelvin ground reference for PGA-1 input.
15 PGA3_GND power_in Kelvin ground reference for PGA-3 input.
16 PGA5_IN input Input to PGA-5, the programmable gain amplifier (gains 3, 6, 12, 24).
17 C4 input ADC-C input 4 with CMPSS-5 comparator inputs and digital input AIO239.
18 PGA1_IN input Input to PGA-1, the programmable gain amplifier (gains 3, 6, 12, 24).
19 C0 input ADC-C input 0 with CMPSS-1 comparator inputs and digital input AIO237.
20 PGA3_IN input Input to PGA-3, the programmable gain amplifier (gains 3, 6, 12, 24).
21 C2 input ADC-C input 2 with CMPSS-3 comparator inputs and digital input AIO244.
22 A1/DACB_OUT input ADC-A input 1, also buffered DAC-B output (output function when DAC enabled).
23 A0/B15/C15/DACA_OUT input ADC-A input 0 (also ADC-B 15, ADC-C 15) shared with buffered DAC-A output.
24 VREFHIB,VREFHIC bidirectional ADC-B and ADC-C high reference voltage; driven externally in external reference mode, and a 2.2µF capacitor is required on the pin.
25 VREFHIA bidirectional ADC-A high reference voltage; driven externally in external reference mode, and a 2.2µF capacitor is required on the pin.
26 VREFLOB,VREFLOC input ADC-B and ADC-C low reference voltage input.
27 VREFLOA input ADC-A low reference voltage input.
28 C5/PGA6_IN input ADC-C input 5 with CMPSS-6 comparator inputs, and input to PGA-6.
29 C1 input ADC-C input 1 with CMPSS-2 comparator inputs and digital input AIO238.
30 PGA2_IN input Input to PGA-2, the programmable gain amplifier (gains 3, 6, 12, 24).
31 C3/PGA4_IN input ADC-C input 3 with CMPSS-4 comparator inputs, also input to PGA-4.
32 PGA2_GND,PGA4_GND,PGA6_GND power_in Kelvin ground reference shared by PGA-2, PGA-4 and PGA-6.
33 VSSA power_in Analog ground pin.
34 VDDA power_in 3.3V analog supply pin; place a decoupling capacitor of at least 2.2µF to VSSA.
35 A5 input ADC-A input 5 with CMPSS-2 comparator inputs and digital input AIO234.
36 A4/B8/PGA2_OF input ADC-A input 4 (also ADC-B input 8 and PGA-2 output filter); analog pin.
37 A8/PGA6_OF input ADC-A input 8 with PGA-6 output filter and CMPSS-6 comparator input.
38 A9 input ADC-A input 9 with CMPSS-6 comparator inputs and digital input AIO236.
39 B4/C8/PGA4_OF input ADC-B input 4 (also ADC-C input 8 and PGA-4 output filter); analog pin.
40 A10/B1/C10/PGA7_OF input ADC-A input 10 (also ADC-B input 1 and ADC-C input 10) with PGA-7 output filter.
41 B0 input ADC-B input 0 with CMPSS-7 comparator inputs and digital input AIO241.
42 PGA7_GND power_in Kelvin ground reference for PGA-7 input.
43 PGA7_IN input Input to PGA-7, the programmable gain amplifier (gains 3, 6, 12, 24).
44 C14 input ADC-C input 14 with CMPSS-7 comparator inputs and digital input AIO246.
45 VSS power_in Digital ground pin that must be connected to the board ground.
46 VDD power_in 1.2V digital logic supply pin; place decoupling capacitance on each VDD pin.
47 VDDIO power_in 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF.
48 FLT2 bidirectional Flash test pin 2 reserved for TI; must be left unconnected.
49 FLT1 bidirectional Flash test pin 1 reserved for TI; must be left unconnected.
50 GPIO13 bidirectional General-purpose I/O 13 with EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX and PMBUSA_ALERT alternate functions.
51 GPIO12 bidirectional General-purpose I/O 12 with EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX and PMBUSA_CTL alternate functions.
52 GPIO11 bidirectional General-purpose I/O 11 with EPWM6_B, SCIB_RX, EQEP1_B, SPIA_STE and FSIRXA_D1 alternate functions.
53 GPIO33 bidirectional General-purpose I/O 33 with I2CA_SCL, SPIB_STE, LINA_RX, SD1_C3 and CANA_RX alternate functions.
54 GPIO16 bidirectional General-purpose I/O 16 with SPIA_SIMO, CANB_TX, EPWM5_A, SD1_D1 and XCLKOUT alternate functions.
55 GPIO17 bidirectional General-purpose I/O 17 with SPIA_SOMI, CANB_RX, EPWM5_B, SD1_C1 and PMBUSA_SDA alternate functions.
56 GPIO24 bidirectional General-purpose I/O 24 with OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO and ERRORSTS alternate functions.
57 GPIO25 bidirectional General-purpose I/O 25 with OUTPUTXBAR2, EQEP2_B, SPIB_SOMI, SD1_C1 and SCIA_RX alternate functions.
58 GPIO26 bidirectional General-purpose I/O 26 with OUTPUTXBAR3, EQEP2_INDEX, SPIB_CLK, SD1_D2 and I2CA_SDA alternate functions.
59 GPIO27 bidirectional General-purpose I/O 27 with OUTPUTXBAR4, EQEP2_STROBE, SPIB_STE, SD1_C2 and I2CA_SCL alternate functions.
60 TCK input JTAG test clock input with internal pull-up enabled.
61 GPIO37/TDO output JTAG test data output TDO by default (tri-stated when JTAG is inactive); otherwise GPIO37 with OUTPUTXBAR2, I2CA_SCL and SCIA_TX alternate functions.
62 TMS bidirectional JTAG test mode select with internal pull-up; an external 2.2kΩ pull-up to VDDIO is recommended.
63 GPIO35/TDI input JTAG test data input TDI by default; otherwise GPIO35 with SCIA_RX, I2CA_SDA, CANA_RX and EQEP1_A alternate functions.
64 GPIO32 bidirectional General-purpose I/O 32 with I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3 and CANA_TX alternate functions.
65 GPIO56 bidirectional General-purpose I/O 56 with SPIA_CLK, EQEP2_STROBE, SCIB_TX, SD1_D3 and SPIB_SIMO alternate functions.
66 GPIO57 bidirectional General-purpose I/O 57 with SPIA_STE, EQEP2_INDEX, SCIB_RX, SD1_C3 and SPIB_SOMI alternate functions.
67 GPIO58 bidirectional General-purpose I/O 58 with OUTPUTXBAR1, SPIB_CLK, SD1_D4, LINA_TX and CANB_TX alternate functions.
68 GPIO18_X2 bidirectional General-purpose I/O 18 or crystal oscillator output X2; GPIO18 is usable only when the system is clocked by INTOSC and X1 has an external pull-down (recommended 1kΩ).
69 X1 bidirectional Crystal oscillator input or single-ended 3.3V clock input; the device initialization software must configure this pin before enabling the oscillator.
70 VDDIO power_in 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF.
71 VDD power_in 1.2V digital logic supply pin; place decoupling capacitance on each VDD pin.
72 VSS power_in Digital ground pin that must be connected to the board ground.
73 VREGENZ input Internal regulator enable with internal pull-down; tie to VSS to enable the internal VREG or to VDDIO to use an external 1.2V supply.
74 GPIO8 bidirectional General-purpose I/O 8 with EPWM5_A, CANB_TX, ADCSOCAO, SCIA_TX, SPIA_SIMO and I2CA_SCL alternate functions.
75 GPIO4 bidirectional General-purpose I/O 4 with EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK alternate functions.
76 GPIO3 bidirectional General-purpose I/O 3 with EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and FSIRXA_D0 alternate functions.
77 GPIO2 bidirectional General-purpose I/O 2 with EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX and FSIRXA_D1 alternate functions.
78 GPIO1 bidirectional General-purpose I/O 1 with EPWM1_B and I2CA_SCL alternate functions; open-drain on the I2C function.
79 GPIO0 bidirectional General-purpose I/O 0 with EPWM1_A and I2CA_SDA alternate functions; open-drain on the I2C function.
80 VDDIO_SW power_in 3.3V supply for the internal DC/DC regulator; a 20µF bulk input capacitor is required and it must be tied to VDDIO.
81 GPIO23_VSW bidirectional General-purpose I/O 23 that defaults to the DC/DC switching node VSW when DCDCEN=1; internal capacitance is about 100pF.
82 VSS_SW power_in Internal DC/DC regulator ground; must be tied to the VSS pin.
83 GPIO22_VFBSW bidirectional General-purpose I/O 22 that defaults to the DC/DC feedback VFBSW; when the internal DC/DC is used, connect it to the node where L(VSW) connects to the VDD rail.
84 GPIO7 bidirectional General-purpose I/O 7 with EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK alternate functions.
85 GPIO40 bidirectional General-purpose I/O 40 with PMBUSA_SDA, FSIRXA_D0, SCIB_TX and EQEP1_A alternate functions.
86 VSS power_in Digital ground pin that must be connected to the board ground.
87 VDD power_in 1.2V digital logic supply pin; place decoupling capacitance on each VDD pin.
88 VDDIO power_in 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF.
89 GPIO5 bidirectional General-purpose I/O 5 with EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1 alternate functions.
90 GPIO9 bidirectional General-purpose I/O 9 with EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX and SPIA_CLK alternate functions.
91 GPIO39 bidirectional General-purpose I/O 39 with CANB_RX and FSIRXA_CLK alternate functions.
92 GPIO59 bidirectional General-purpose I/O 59 with OUTPUTXBAR2, SPIB_STE, SD1_C4, LINA_RX, CANB_RX and EQEP1_INDEX alternate functions.
93 GPIO10 bidirectional General-purpose I/O 10 with EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI and I2CA_SDA alternate functions.
94 GPIO34 bidirectional General-purpose I/O 34 with OUTPUTXBAR1 and PMBUSA_SDA alternate functions.
95 GPIO15 bidirectional General-purpose I/O 15 with EPWM8_B, SCIB_RX, OUTPUTXBAR4, PMBUSA_SCL, SPIB_STE and EQEP2_B alternate functions.
96 GPIO14 bidirectional General-purpose I/O 14 with EPWM8_A, SCIB_TX, OUTPUTXBAR3, PMBUSA_SDA, SPIB_CLK and EQEP2_A alternate functions.
97 GPIO6 bidirectional General-purpose I/O 6 with EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0 alternate functions.
98 GPIO30 bidirectional General-purpose I/O 30 with CANA_RX, SPIB_SIMO, OUTPUTXBAR7, EQEP1_STROBE and SD1_D4 alternate functions.
99 GPIO31 bidirectional General-purpose I/O 31 with CANA_TX, SPIB_SOMI, OUTPUTXBAR8, EQEP1_INDEX, SD1_C4 and FSIRXA_D1 alternate functions.
100 GPIO29 bidirectional General-purpose I/O 29 with SCIA_TX, EPWM7_B, OUTPUTXBAR6, EQEP1_B, SD1_C3, LINA_RX and ERRORSTS alternate functions.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TQFP-100(14x14)
Category Embedded Processors & Controllers
Pins 100

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VDDIO 电源电压 VDDIO -0.3 4.6 V 以 VSS 为基准 59
VDDA 电源电压 VDDA -0.3 4.6 V 以 VSSA 为基准 59
VDD 电源电压 VDD -0.3 1.5 V 以 VSS 为基准 59
输入电压 (3.3V) VIN -0.3 4.6 V 59
输出电压 VO -0.3 4.6 V 59
数字输入钳位电流(每引脚) IIK -20 20 mA VIN < VSS 或 VIN > VDDIO 59
模拟输入钳位电流(每引脚) IIKANALOG -20 20 mA VIN < VSSA 或 VIN > VDDA 59
所有输入钳位电流总计 IIKTOTAL -20 20 mA VIN < VSS/VSSA 或 VIN > VDDIO/VDDA 59
数字输出电流(每引脚) IOUT -20 20 mA 59
自然通风温度 TA -40 125 °C 59
工作结温 TJ -40 150 °C 59
贮存温度 Tstg -65 150 °C 59
器件电源电压 VDDIO 和 VDDA VDDIO 3.3 3.63 V 启用内部 BOR 60
器件电源电压 VDDIO 和 VDDA VDDIO 2.8 3.3 3.63 V 禁用内部 BOR 60
器件电源电压 VDD VDD 1.14 1.2 1.32 V 60
结温 TJ(S 版本) TJ -40 125 °C S 版本 60
自然通风温度 TA(Q 版本) TA -40 125 °C Q 版本(AEC Q100 认证) 60
高电平输入电压 (3.3V) VIH 2 V 68
低电平输入电压 (3.3V) VIL 0.8 V 68
输入迟滞 VHYSTERESIS 150 mV 68
VDDIO 欠压复位电压 VBOR-VDDIO 2.81 3 V 68
运行模式 VDD 电流消耗 IDD 61 90 mA 运行模式 62
运行模式 VDDIO 电流消耗 IDDIO 26 45 mA 运行模式 62
运行模式 VDDA 电流消耗 IDDA 12 30 mA 运行模式 62
空闲模式 VDD 电流消耗 IDD 18 40 mA 空闲模式 62
空闲模式 VDDIO 电流消耗 IDDIO 1.2 4 mA 空闲模式 62
空闲模式 VDDA 电流消耗 IDDA 0.9 1.2 mA 空闲模式 62
停机模式 VDD 电流消耗 IDD 0.9 20 mA 停机模式 62
停机模式 VDDIO 电流消耗 IDDIO 0.8 4 mA 停机模式 62
停机模式 VDDA 电流消耗 IDDA 0.2 0.5 mA 停机模式 62
闪存擦除/编程 VDD 电流消耗 IDD 40 70 mA 擦除/编程周期 62
闪存擦除/编程 VDDIO 电流消耗 IDDIO 33 75 mA 擦除/编程周期 62
闪存擦除/编程 VDDA 电流消耗 IDDA 0.1 2.5 mA 擦除/编程周期 62
内部稳压器输出 VVREG 1.14 1.2 1.32 V 81
内部振荡器频率 INTOSC1 和 INTOSC2 fINTOSC 9.7 10 10.3 MHz 95
频率稳定性 fINTOSC-STABILITY -3 3 % 96
ADCCLK(源自 PERx.SYSCLK) 5 50 MHz 124
VREFHI 外部基准 VREFHI 2.4 V 外部基准 124
ADC 增益误差(内部基准电压) -45 45 LSB 内部基准电压 125
ADC 增益误差(外部基准) -5 5 LSB 外部基准 125
ADC 偏移量误差 -5 5 LSB 125
ADC DNL 误差 -1 1 LSB 125
ADC INL 误差 -2 2 LSB 125
缓冲 DAC 有效输出电压范围 (RL=5kΩ) VOUT 0.3 V RL = 5kΩ 137
缓冲 DAC 有效输出电压范围 (RL=1kΩ) VOUT 0.6 V RL = 1kΩ 137
缓冲 DAC 增益误差 -2.5 2.5 FSR 百分比 138
缓冲 DAC DNL -1 1 LSB 已更正端点 138
缓冲 DAC INL -5 5 LSB 已更正端点 138
比较器以输入为基准的偏移量误差 -20 20 mV 低共模,反相输入设置为 50mV 144
CMPSS DAC 静态偏移量误差 -25 25 mV 145
CMPSS DAC 静态增益误差 -2 2 FSR 百分比 145
CMPSS DAC 静态 DNL -1 4 LSB 已更正端点 145
CMPSS DAC 静态 INL -16 16 LSB 已更正端点 145
SCL 时钟频率(PMBus 快速模式) fSCL 10 400 kHz 快速模式 177
SCL 时钟频率(PMBus 标准模式) fSCL 10 100 kHz 标准模式 178
结至外壳热阻 RΘJC 7.6 °C/W PZ 封装 69
结至电路板热阻 RΘJB 24.2 °C/W PZ 封装 69
结至大气热阻(高 k PCB) RΘJA 46.1 °C/W 高 k PCB,0 lfm,PZ 封装 69

CAD (KiCad official)

  • Symbol: F280049PZQ
  • Footprint: Package_QFP:TQFP-100_14x14mm_P0.5mm
  • 3D model: TQFP-100(14x14) (KiCad packages3D, STEP)
  • 3D model files: f280049pzq-etched.step / f280049pzq-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); f280049pzq.step / f280049pzq.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (270 pp, sha256 f0eccdafc7ec75fa, retrieved 2026-11-02, tier: manufacturer)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF