component
NCP114ASN180T1G
Public Made by Adomby adom
onsemi Linear Voltage Regulators (LDO), TSOP-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownNCP114ASN180T1G
onsemi · Linear Voltage Regulators (LDO) · TSOP-5
NCP114ASN180T1G from onsemi, in a TSOP-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Input pin; a small capacitor (1 µF ceramic recommended) is needed from this pin to ground to assure stability, operating input range 1.7 V to 5.5 V. |
| 2 | GND | power_in | Power supply ground. |
| 3 | EN | input | Driving EN over 0.9 V turns on the regulator and driving it below 0.4 V puts the regulator into shutdown mode; it has an internal pull-down so tie to IN if unused. |
| 4 | N/C | unconnected | Not connected; this pin can be tied to ground to improve thermal dissipation. |
| 5 | OUT | power_out | Regulated output voltage pin (1.8 V for this option); a ceramic capacitor with minimum value of 1 µF is needed from this pin to ground to assure stability. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | onsemi |
| Package | TSOP-5 |
| Category | Power Management ICs |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Input Voltage | VIN | 1.7 | 5.5 | V | 3 | ||
| Output Voltage Accuracy | VOUT | -40 | 40 | mV | -40°C ≤ TJ ≤ 85°C, VOUT ≤ 2.0 V | 3 | |
| Line Regulation | RegLINE | 0.01 | 0.1 | %/V | VOUT + 0.5 V ≤ VIN ≤ 5.5 V (VIN ≥ 1.7 V) | 3 | |
| Load Regulation - TSOP-5 | RegLOAD | 28 | 45 | mV | IOUT = 1 mA to 300 mA | 3 | |
| Output Current Limit | ICL | 300 | 600 | mA | VOUT = 90% VOUT(nom) | 3 | |
| Ground Current | IQ | 50 | 95 | µA | IOUT = 0 mA | 3 | |
| Shutdown Current | IDIS | 0.01 | 1 | µA | VEN ≤ 0.4 V, VIN = 5.5 V | 3 | |
| EN Pin Input Current | IEN | 0.3 | 1 | µA | VEN = 5.5 V | 3 | |
| EN High Threshold | VEN_HI | 0.9 | V | VEN voltage increasing | 3 | ||
| EN Low Threshold | VEN_LO | 0.4 | V | VEN voltage decreasing | 3 | ||
| Load Transient | TranLOAD | -50 | 30 | mV | IOUT = 1 mA to 300 mA or 300 mA to 1 mA in 1 µs, COUT = 1 µF | 3 | |
| Power Supply Rejection Ratio | PSRR | 75 | dB | VIN = 3.6 V, VOUT = 3.1 V, IOUT = 150 mA, f = 1 kHz | 3 | ||
| Output Noise Voltage | VN | 70 | µVrms | VIN = 2.5 V, VOUT = 1.8 V, IOUT = 150 mA, f = 10 Hz to 100 kHz | 3 | ||
| Thermal Shutdown Temperature | TSD | 160 | °C | Temperature increasing from TJ = +25°C | 3 | ||
| Thermal Shutdown Hysteresis | TSDH | 20 | °C | Temperature falling from TSD | 3 | ||
| Active Output Discharge Resistance | RDIS | 100 | Ω | VEN < 0.4 V, Version A only | 3 | ||
| Input Voltage | VIN | -0.3 | 6 | V | 2 | ||
| Output Voltage | VOUT | -0.3 | 6 | V | -0.3 V to VIN + 0.3 V or 6 V | 2 | |
| Enable Input | VEN | -0.3 | 6 | V | -0.3 V to VIN + 0.3 V or 6 V | 2 | |
| Maximum Junction Temperature | TJ(MAX) | 150 | °C | 2 | |||
| Storage Temperature | TSTG | -55 | 150 | °C | 2 | ||
| ESD Capability, Human Body Model | ESDHBM | 2000 | V | 2 | |||
| ESD Capability, Machine Model | ESDMM | 200 | V | 2 | |||
| Thermal Resistance, Junction-to-Air, TSOP-5 | RθJA | 236 | °C/W | 1 oz FR4 PCB with 645 mm2 Cu area | 2 | ||
| Operating Junction Temperature | TJ | -40 | 85 | °C | Electrical characteristics range | 3 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | copper area connected to the pins will also improve the | 14 |
CAD (KiCad official)
- Symbol:
NCP114ASN180T1G - Footprint:
Package_SO:TSOP-5_1.65x3.05mm_P0.95mm - 3D model: TSOP-5 (KiCad packages3D, STEP)
- 3D model files:
ncp114asn180t1g-etched.step/ncp114asn180t1g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ncp114asn180t1g.step/ncp114asn180t1g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: onsemi datasheet (18 pp, sha256
4d6237af973fa850, retrieved 2026-10-23, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).