3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSTM6710LWB7F
STMicroelectronics · Monitors & Reset Circuits · SOT-23-6
STM6710LWB7F from STMicroelectronics, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V1IN | input | Monitored input 1 is compared against a factory-set trip point or an adjustable threshold of 0.62 V typ set by an external divider, with input current of ±0.4 µA max on the adjustable input. |
| 2 | V2IN | power_in | Input voltage 2 is also the STM6710 device power supply and is itself monitored, with an operating supply of 1.0 to 5.5 V (0 to T_max °C) or 1.2 to 5.5 V (-40 to T_max °C). |
| 3 | V3IN | input | Monitored input 3 is compared against a factory-set trip point or an adjustable threshold of 0.62 V typ set by an external divider, with input current of less than ±0.2 µA on the adjustable input. |
| 4 | V4IN | input | Monitored input 4 is compared against a factory-set trip point or an adjustable threshold of 0.62 V typ set by an external divider, with input current of less than ±0.2 µA on the adjustable input. |
| 5 | GND | power_in | Ground pin for the power supply, tied to VSS. |
| 6 | RESET | output | Active-low open-drain reset output that goes low when any monitored input falls below its threshold, with a weak 10 µA internal pull-up to V2IN and a typical 200 ms reset timeout on the STM6710. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SOT-23-6 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature | TSTG | -55 | 150 | °C | VCC off | 11 | |
| Lead solder temperature | TSLD | 260 | °C | 10 seconds | 11 | ||
| Input or output voltage | VIO | -0.3 | V | max printed as VCC + 0.3 | 11 | ||
| Supply voltage | VCC | -0.3 | 7 | V | 11 | ||
| Output current | IO | 20 | mA | 11 | |||
| V2IN supply voltage | V2IN | 1 | 5.5 | V | TA = 0 to T_max °C | 12 | |
| V2IN supply voltage | V2IN | 1.2 | 5.5 | V | TA = -40 to T_max °C | 12 | |
| Ambient operating temperature | TA | -40 | 105 | °C | 12 | ||
| Reset threshold 2.5 V (-5%) | Vrst | 2.25 | 2.32 | 2.38 | V | VxIN falling | 12 |
| Reset threshold 1.8 V (-5%) | Vrst | 1.62 | 1.67 | 1.71 | V | VxIN falling | 12 |
| Adjustable reset threshold voltage | Vrstxin | 0.611 | 0.62 | 0.629 | V | VxIN decreasing | 13 |
| Reset timeout delay | tREC | 140 | 200 | 280 | ms | STM6710 | 13 |
| RESET output low | VOL | 0.3 | V | V2IN, VCC = 5 V, ISINK = 2 mA | 13 | ||
| RESET output low | VOL | 0.4 | V | V2IN, VCC = 2.5 V, ISINK = 1.2 mA | 13 | ||
| RESET output high | VOH | 0.8 | x V2IN | VCC ≥ VTH, ISOURCE = -6 µA, RESET deasserted | 13 | ||
| Input current (1.8 V, 2.5 V, 5.0 V supplies) | IxIN | 25 | 40 | µA | VxIN nominal input voltage (1.8 V, 2.5 V, 5.0 V supplies) | 12 | |
| Input current (V1IN adjustable) | IxIN | 0.4 | µA | V1IN = 0 to 0.85 V (for adjustable thresholds) | 12 | ||
| Input current (V3IN, V4IN adjustable) | IxIN | 0.2 | µA | V3IN, V4IN = 0 to 0.85 V (for adjustable thresholds) | 12 | ||
| VTH to reset asserted delay | tRPD | 30 | µs | VxIN falling at 10 mV/µs from VTH to (VTH -50 mV) | 13 | ||
| Hysteresis of VTH | VHYST | 0.3 | % VTH | 13 | |||
| Reset threshold temperature coefficient | TCVTH | 60 | ppm/°C | 13 | |||
| RESET output high source current | IOH | 10 | µA | V2IN ≥ 2.0 V, RESET deasserted | 13 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
STM6710LWB7F - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated on the KiCad land (body 1.625 x 2.925 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
stm6710lwb7f-etched.step/stm6710lwb7f-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm6710lwb7f.step/stm6710lwb7f.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (20 pp, sha256
c500f2ef39e8a69c, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).