3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownMAX96724GTN/VY+
ADI(亚德诺)/MAXIM(美信) · IC · TQFN-56-EP(8x8)
MAX96724GTN from ADI(亚德诺)/MAXIM(美信), in a TQFN-56-EP(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MFP0 | bidirectional | Multifunction pin that is Disabled (Hi-Z with 1MΩ pulldown) at power-up and can be configured as FSYNC (master output or slave input), line-fault monitor input LMN0, or GPIO0. |
| 2 | MFP1 | bidirectional | Multifunction pin that is Disabled (Hi-Z) at power-up and can be configured as push-pull VSYNC0/DE0/HSYNC0 output, line-fault monitor input LMN1, or GPIO1 with 1MΩ pulldown. |
| 3 | MFP2 | bidirectional | Multifunction pin that is Disabled (Hi-Z) at power-up and can be configured as line-fault monitor input LMN2 or GPIO2 with 1MΩ pulldown. |
| 4 | CFG0 | input | Configuration input sampled at power-up or reset through an external resistor divider from VDDIO to ground to select the mapped configuration and device address per Table 7. |
| 5 | SIODP | bidirectional | Noninverted GMSL2/GMSL1 serial-data I/O D link connection to the remote serializer. |
| 6 | SIODN | bidirectional | Inverted GMSL2/GMSL1 serial-data I/O D link connection to the remote serializer. |
| 7 | VDD18 | power_in | 1.8V analog supply input. |
| 8 | CAP_VDD | passive | Decoupling connection for the VDD core supply. |
| 9 | SIOCN | bidirectional | Inverted GMSL2/GMSL1 serial-data I/O C link connection to the remote serializer. |
| 10 | SIOCP | bidirectional | Noninverted GMSL2/GMSL1 serial-data I/O C link connection to the remote serializer. |
| 11 | PWDNB | input | Active-low power-down input with 1MΩ internal pulldown; set low to enter power-down mode and attach a pullup to VDDIO for normal operation. |
| 12 | MFP3 | bidirectional | Multifunction pin that is Disabled (Hi-Z) at power-up and can be configured as push-pull VSYNC1/DE1/HSYNC1 output, line-fault monitor input LMN3, or GPIO3 with 1MΩ pulldown. |
| 13 | MFP4 | bidirectional | Multifunction pin defaulting to LOCK output (open-drain with 40kΩ pullup to VDDIO) or configurable as GPIO4. |
| 14 | MFP5 | bidirectional | Multifunction pin defaulting to ERRB output (open-drain with 40kΩ pullup to VDDIO) or configurable as ERRB/LOCK or GPIO5. |
| 15 | X1/OSC | input | 25MHz crystal or external 25MHz clock source input (frequency tolerance ±200ppm for crystal). |
| 16 | X2 | passive | Connect to the 25MHz crystal; must be left floating when an external oscillator is driven into X1/OSC. |
| 17 | XRES | passive | Connect a 402Ω 1% resistor to ground. |
| 18 | SIOBP | bidirectional | Noninverted GMSL2/GMSL1 serial-data I/O B link connection to the remote serializer. |
| 19 | SIOBN | bidirectional | Inverted GMSL2/GMSL1 serial-data I/O B link connection to the remote serializer. |
| 20 | CAP_VDD | passive | Decoupling connection for the VDD core supply. |
| 21 | VDD18 | power_in | 1.8V analog supply input. |
| 22 | SIOAN | bidirectional | Inverted GMSL2/GMSL1 serial-data I/O A link connection to the remote serializer. |
| 23 | SIOAP | bidirectional | Noninverted GMSL2/GMSL1 serial-data I/O A link connection to the remote serializer. |
| 24 | VDDIO | power_in | 3.3V or 1.8V I/O power supply input (VDDIO = 1.7V to 3.6V per electrical characteristics). |
| 25 | CFG1/MFP6 | bidirectional | CFG1 input latched at power-up (Table 8) and then disabled to Hi-Z; alternately usable as GPIO aggregation or GPO6 general-purpose output. |
| 26 | SDA1/MFP7 | bidirectional | Open-drain I2C SDA1 with 40kΩ pullup to VDDIO by default; alternately FSYNC (ALT), VSYNC2/DE2/HSYNC2 push-pull outputs, or GPIO7. |
| 27 | SCL1/MFP8 | bidirectional | Open-drain I2C SCL1 output with 40kΩ pullup to VDDIO by default; alternately VSYNC3/DE3/HSYNC3 push-pull outputs or GPIO8. |
| 28 | SDA | bidirectional | Main I2C serial data line, open-drain with 40kΩ pullup to VDDIO. |
| 29 | SCL | input | Main I2C serial clock line, open-drain with 40kΩ pullup to VDDIO. |
| 30 | VTERM | power_in | 1.2V CSI C-PHY/D-PHY supply input (VTERM = 1.14V to 1.26V per electrical characteristics). |
| 31 | DA0P | output | Noninverted MIPI D-PHY Port A data lane 0 output (default in 4-lane mode); alternately C-PHY A0A or D-PHY Port C data lane 0 DC0P in 2-lane mode. |
| 32 | DA0N | output | Inverted MIPI D-PHY Port A data lane 0 output (default in 4-lane mode); alternately C-PHY A0B or D-PHY Port C data lane 0 DC0N in 2-lane mode. |
| 33 | CKCP | output | Noninverted MIPI D-PHY Port C clock lane output; disabled in 4-lane mode, alternately CKAP(alt) or C-PHY A0C/C0C. |
| 34 | CKCN | output | Inverted MIPI D-PHY Port C clock lane output; disabled in 4-lane mode, alternately CKAN(alt) or C-PHY A1A/C1A. |
| 35 | DA1P | output | Noninverted MIPI D-PHY Port A data lane 1 output (default in 4-lane mode); alternately C-PHY A1B or D-PHY Port C data lane 1 DC1P. |
| 36 | DA1N | output | Inverted MIPI D-PHY Port A data lane 1 output (default in 4-lane mode); alternately C-PHY A1C or D-PHY Port C data lane 1 DC1N. |
| 37 | DA2P | output | Noninverted MIPI D-PHY Port A data lane 2 output (default in 4-lane mode); alternately C-PHY A2A or D-PHY Port D data lane 0 DD0P. |
| 38 | DA2N | output | Inverted MIPI D-PHY Port A data lane 2 output (default in 4-lane mode); alternately C-PHY A2B or D-PHY Port D data lane 0 DD0N. |
| 39 | CKAP | output | Noninverted MIPI D-PHY Port A clock lane output (default in 4-lane mode); disabled when CKAP/N(alt) is enabled, alternately D-PHY Port D clock CKDP. |
| 40 | CKAN | output | Inverted MIPI D-PHY Port A clock lane output (default in 4-lane mode); disabled when CKAP/N(alt) is enabled, alternately D-PHY Port D clock CKDN. |
| 41 | DA3P | output | Noninverted MIPI D-PHY Port A data lane 3 output (default in 4-lane mode); alternately C-PHY A3B or D-PHY Port D data lane 1 DD1P. |
| 42 | DA3N | output | Inverted MIPI D-PHY Port A data lane 3 output (default in 4-lane mode); alternately C-PHY A3C or D-PHY Port D data lane 1 DD1N. |
| 43 | DB0P | output | Noninverted MIPI D-PHY Port B data lane 0 output (default in 4-lane mode); alternately D-PHY Port E data lane 0 DE0P or C-PHY B0A. |
| 44 | DB0N | output | Inverted MIPI D-PHY Port B data lane 0 output (default in 4-lane mode); alternately D-PHY Port E data lane 0 DE0N or C-PHY B0B. |
| 45 | CKBP | output | Noninverted MIPI D-PHY Port B clock lane output (default in 4-lane mode); disabled when CKBP/N(alt) is enabled, alternately D-PHY Port E clock CKEP. |
| 46 | CKBN | output | Inverted MIPI D-PHY Port B clock lane output (default in 4-lane mode); disabled when CKBP/N(alt) is enabled, alternately D-PHY Port E clock CKEN. |
| 47 | DB1P | output | Noninverted MIPI D-PHY Port B data lane 1 output (default in 4-lane mode); alternately D-PHY Port E data lane 1 DE1P or C-PHY B1B. |
| 48 | DB1N | output | Inverted MIPI D-PHY Port B data lane 1 output (default in 4-lane mode); alternately D-PHY Port E data lane 1 DE1N or C-PHY B1C. |
| 49 | DB2P | output | Noninverted MIPI D-PHY Port B data lane 2 output (default in 4-lane mode); alternately D-PHY Port F data lane 0 DF0P or C-PHY B2A. |
| 50 | DB2N | output | Inverted MIPI D-PHY Port B data lane 2 output (default in 4-lane mode); alternately D-PHY Port F data lane 0 DF0N or C-PHY B2B. |
| 51 | CKFP | output | Noninverted MIPI D-PHY Port F clock lane output (2-lane mode); disabled in 4-lane mode, alternately CKBP(alt) or C-PHY B2C/F0C. |
| 52 | CKFN | output | Inverted MIPI D-PHY Port F clock lane output (2-lane mode); disabled in 4-lane mode, alternately CKBN(alt) or C-PHY B3A/F1A. |
| 53 | DB3P | output | Noninverted MIPI D-PHY Port B data lane 3 output (default in 4-lane mode); alternately D-PHY Port F data lane 1 DF1P or C-PHY B3B. |
| 54 | DB3N | output | Inverted MIPI D-PHY Port B data lane 3 output (default in 4-lane mode); alternately D-PHY Port F data lane 1 DF1N or C-PHY B3C. |
| 55 | VDD | power_in | 1.2V or 1.0V core supply; 1.2V uses an internal regulator and 1.0V bypasses the regulator. |
| 56 | VDD | power_in | 1.2V or 1.0V core supply; 1.2V uses an internal regulator and 1.0V bypasses the regulator. |
| 57 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ADI(亚德诺)/MAXIM(美信) |
| Package | TQFN-56-EP(8x8) |
| Category | |
| Pins | 57 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage on VDDIO (absolute max) | VDDIO | -0.3 | 3.9 | V | All voltages with respect to ground; Note c: specified max or 3.9V, whichever is lower | 7 | |
| Voltage on VDD18 (absolute max) | VDD18 | -0.3 | 2 | V | 7 | ||
| Voltage on VDD (absolute max) | VDD | -0.3 | 2 | V | 7 | ||
| Voltage on VTERM (absolute max) | VTERM | -0.3 | 1.32 | V | 7 | ||
| Voltage on CAP_VDD (absolute max) | CAP_VDD | -0.3 | 1.2 | V | 7 | ||
| SIO_ voltage, inactive state (absolute max) | SIO_ | -0.3 | 1.1 | V | Inactive state = device not in power-down mode (Note a) | 7 | |
| Storage temperature range | -40 | 150 | °C | 7 | |||
| Supply range VTERM | VTERM | 1.14 | 1.2 | 1.26 | V | 25 | |
| Supply range VDD18 | VDD18 | 1.7 | 1.8 | 1.9 | V | 25 | |
| Supply range VDD (1.0V nominal) | VDD | 0.95 | 1 | 1.05 | V | VDD 1.0V nominal option | 25 |
| Supply range VDD (1.2V nominal) | VDD | 1.14 | 1.2 | 1.26 | V | VDD 1.2V nominal option | 25 |
| Supply range VDDIO | VDDIO | 1.7 | 3.6 | V | 25 | ||
| Operating junction temperature TJ | TJ | -40 | 125 | ºC | 25 | ||
| Single-ended reverse channel output voltage swing | VO | 190 | 250 | 310 | mV | RL = 100Ω ±1% | 8 |
| Differential reverse channel output voltage swing (p-p) | VODT | 380 | 500 | 620 | mV | RL = 100Ω ±1%, peak-to-peak differential voltage | 8 |
| Change in VOD between complementary output states | ΔVOD | 25 | mV | RL = 100Ω ±1%, /VOD(H) − VOD(L)/ | 8 | ||
| Thevenin high-level output voltage (LP transmitter) | VOH | 0.95 | 1.2 | 1.3 | V | C-PHY and D-PHY LP transmitter | 8 |
| Thevenin low-level output voltage (LP transmitter) | VOL | -50 | 50 | mV | C-PHY and D-PHY LP transmitter | 8 | |
| HS transmit static common-mode voltage (D-PHY) | VCMTX | 150 | 200 | 250 | mV | D-PHY HS transmitter | 9 |
| HS transmit differential voltage (D-PHY) | /VOD/ | 140 | 200 | 270 | mV | D-PHY HS transmitter | 9 |
| VOD mismatch between differential-1 and differential-0 (D-PHY) | /ΔVOD/ | 14 | mV | D-PHY HS transmitter | 9 | ||
| Single-ended output impedance (D-PHY HS) | ZOS | 40 | 50 | 62.5 | Ω | D-PHY HS transmitter | 9 |
| HS transmit static common-point voltage (C-PHY) | VCPTX | 175 | 310 | mV | ZID = 100Ω | 9 | |
| Single-ended output impedance (C-PHY HS) | ZOS | 40 | 50 | 60 | Ω | C-PHY HS transmitter | 9 |
| Supply current IDD1, GMSL2 6Gbps, 1x 4-lane C-PHY (MAX96724) | IDD1 | 19 | 35 | mA | 4x 6Gbps input, 4x 5.2Gbps payload, PRBS24; VTERM = 1.26V | 11 | |
| Supply current IDD1, GMSL2 6Gbps, 1x 4-lane C-PHY (MAX96724) | IDD1 | 280 | 325 | mA | 4x 6Gbps input, 4x 5.2Gbps payload, PRBS24; VDD18 = 1.9V | 11 | |
| Supply current IDD1, GMSL2 6Gbps, 1x 4-lane C-PHY (MAX96724) | IDD1 | 244 | 675 | mA | 4x 6Gbps input, 4x 5.2Gbps payload, PRBS24; VDD = 1.05V | 11 | |
| Supply current IDD1, GMSL2 6Gbps, 1x 4-lane C-PHY (MAX96724) | IDD1 | 228 | 650 | mA | 4x 6Gbps input, 4x 5.2Gbps payload, PRBS24; VDD = 1.26V | 11 | |
| Supply current IDD2, replicate mode, GMSL2 6Gbps, 2x 4-lane C-PHY (MAX96724) | IDD2 | 37 | 70 | mA | Replicate mode, 4x 6Gbps input, 4x 5.2Gbps payload, PRBS24; VTERM = 1.26V | 11 | |
| Supply current IDD2, replicate mode, GMSL2 6Gbps, 2x 4-lane C-PHY (MAX96724) | IDD2 | 280 | 325 | mA | Replicate mode, 4x 6Gbps input, 4x 5.2Gbps payload, PRBS24; VDD18 = 1.9V | 11 | |
| Supply current IDD2, replicate mode, GMSL2 6Gbps, 2x 4-lane C-PHY (MAX96724) | IDD2 | 272 | 725 | mA | Replicate mode, 4x 6Gbps input, 4x 5.2Gbps payload, PRBS24; VDD = 1.05V | 11 | |
| Supply current IDD2, replicate mode, GMSL2 6Gbps, 2x 4-lane C-PHY (MAX96724) | IDD2 | 265 | 700 | mA | Replicate mode, 4x 6Gbps input, 4x 5.2Gbps payload, PRBS24; VDD = 1.26V | 11 | |
| Power-down current | IDD | 1 | μA | VTERM = 1.26V, TA = +105°C | 12 | ||
| Lock time tLOCK2 (GMSL2) | tLOCK2 | 45 | 60 | ms | From power-up, one-shot reset, or rising edge of PWDNB to rising edge of LOCK | 12 | |
| PWDNB hold time | tHOLD_PWDNB | 1 | μs | Minimum time to reset the device | 12 | ||
| Load capacitance (C-PHY and D-PHY LP transmitter) | CLOAD | 0 | 70 | pF | Note 4 | 13 | |
| Data lane bit rate (D-PHY) | DLBR | 80 | 2500 | Mbps | 14 | ||
| UI instantaneous (D-PHY) | UIINST | 0.4 | 12.5 | ns | 14 | ||
| UI variation (D-PHY) | ΔUI | -10 | 10 | % | UI ≥ 1ns within a single burst | 14 | |
| Static data to clock skew (D-PHY) | TSKEW | -0.2 | 0.2 | UIINST | Static, > 1.5Gbps | 14 | |
| Dynamic data to clock skew (D-PHY) | TSKEW | -0.15 | 0.15 | UIINST | Dynamic, > 1.5Gbps | 14 | |
| C-PHY lane bit rate | CBR | 182 | 5700 | Mbps | 15 | ||
| Time the transmitter drives the 3-wire LP-000 state before HS start (C-PHY) | t3-PREPARE | 38 | 95 | ns | 15 | ||
| SCL clock frequency, low fSCL range | fSCL | 9.6 | 100 | kHz | I2C_MST_BT = 010, I2C_SLV_SH = 10 | 16 | |
| SCL clock frequency, mid fSCL range | fSCL | 100 | 400 | kHz | I2C_MST_BT = 101, I2C_SLV_SH = 01 | 16 | |
| SCL clock frequency, high fSCL range | fSCL | 400 | 1000 | kHz | I2C_MST_BT = 111, I2C_SLV_SH = 00 | 16 | |
| Crystal frequency stability + frequency tolerance | fTN | -200 | 200 | ppm | Reference clock requirements, crystal 25MHz | 17 | |
| External reference frequency stability + frequency tolerance | fTN | -200 | 200 | ppm | External input on X1/OSC, X2 unconnected | 17 | |
| Reference clock duty cycle (external input) | DC | 40 | 50 | 60 | % | External input on X1/OSC, X2 unconnected | 17 |
| SIO_ ESD, Human Body Model | VESD | -8 | 8 | kV | HBM, RD = 1.5kΩ, CS = 100pF | 26 | |
| All other pins ESD, Human Body Model | VESD | -3 | 3 | kV | HBM, RD = 1.5kΩ, CS = 100pF | 26 | |
| XRES resistor RXRES nominal | RXRES | 402 | Ω | Connect the resistor to XRES and ground | 26 | ||
| XRES resistor RXRES tolerance | RXRES | -1 | 1 | % | Connect the resistor to XRES and ground | 26 | |
| Termination resistor for coax mode RTERM nominal | RTERM | 49.9 | Ω | Place near associated SIO_N pin | 26 | ||
| Termination resistor for coax mode RTERM tolerance | RTERM | -1 | 1 | % | Place near associated SIO_N pin | 26 | |
| Thermal resistance junction to ambient (θJA), 56-pin TQFN-SW | θJA | 25 | Four-layer board, JESD51-7 | 7 | |||
| Thermal resistance junction to case (θJC), 56-pin TQFN-SW | θJC | 4 | Four-layer board, JESD51-7 | 7 |
CAD (KiCad official)
- Symbol:
MAX96724GTN - Footprint:
Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP4.5x5.2mm - 3D model: TQFN-56-EP(8x8) (KiCad packages3D, STEP)
- 3D model files:
max96724gtn-etched.step/max96724gtn-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max96724gtn.step/max96724gtn.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ADI(亚德诺)/MAXIM(美信) datasheet (474 pp, sha256
3182d34d76afe981, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
Other parts in this family
This page is MAX96724GTN/VY+. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:
- MAX96724GTN/VY+T