3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMC9S08AW48CFDE
NXP Semicon · NXP MCU · QFN-48-EP(7x7)
MC9S08AW48CFDE from NXP Semicon, in a QFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PTC4 | bidirectional | Port C general-purpose I/O bit 4 with software-selectable input pull-up, output slew-rate control and drive strength; no alternate function is listed for this pin. |
| 2 | IRQ/TPMCLK | input | External interrupt request input (IRQ) with optional internal pull-up/pull-down; it has no clamp diode to VDD, so it must not be driven above VDD. Alternate function TPMCLK. |
| 3 | RESET | input | Active-low reset input with internal pull-up and input hysteresis; a recommended external RC filter is suggested for EMC-sensitive designs. |
| 4 | PTF0/TPM1CH2 | bidirectional | Port F general-purpose I/O bit 0 with pull-up, slew-rate and drive-strength control; alternate function TPM1CH2. |
| 5 | PTF1/TPM1CH3 | bidirectional | Port F general-purpose I/O bit 1 with pull-up, slew-rate and drive-strength control; alternate function TPM1CH3. |
| 6 | PTF4/TPM2CH0 | bidirectional | Port F general-purpose I/O bit 4 with pull-up, slew-rate and drive-strength control; alternate function TPM2CH0. |
| 7 | PTF5/TPM2CH1 | bidirectional | Port F general-purpose I/O bit 5 with pull-up, slew-rate and drive-strength control; alternate function TPM2CH1. |
| 8 | PTF6 | bidirectional | Port F general-purpose I/O bit 6 with pull-up, slew-rate and drive-strength control; no alternate function is listed for this pin. |
| 9 | PTE0/TxD1 | bidirectional | Port E general-purpose I/O bit 0 with pull-up, slew-rate and drive-strength control; alternate function SCI1 transmit (TxD1). |
| 10 | PTE1/RxD1 | bidirectional | Port E general-purpose I/O bit 1 with pull-up, slew-rate and drive-strength control; alternate function SCI1 receive (RxD1). |
| 11 | PTE2/TPM1CH0 | bidirectional | Port E general-purpose I/O bit 2 with pull-up, slew-rate and drive-strength control; alternate function TPM1CH0. |
| 12 | PTE3/TPM1CH1 | bidirectional | Port E general-purpose I/O bit 3 with pull-up, slew-rate and drive-strength control; alternate function TPM1CH1. |
| 13 | PTE4/SS1 | bidirectional | Port E general-purpose I/O bit 4 with pull-up, slew-rate and drive-strength control; alternate function SPI slave select (SS1). |
| 14 | PTE5/MISO1 | bidirectional | Port E general-purpose I/O bit 5 with pull-up, slew-rate and drive-strength control; alternate function SPI MISO1. |
| 15 | PTE6/MOSI1 | bidirectional | Port E general-purpose I/O bit 6 with pull-up, slew-rate and drive-strength control; alternate function SPI MOSI1. |
| 16 | PTE7/SPSCK1 | bidirectional | Port E general-purpose I/O bit 7 with pull-up, slew-rate and drive-strength control; alternate function SPI clock SPSCK1. |
| 17 | VSS | power_in | Ground supply pin for the MCU core and I/O buffers. |
| 18 | VDD | power_in | Main positive power supply pin; supplies all I/O buffers and the internal voltage regulator, with a 0.1 µF ceramic bypass recommended close to VDD/VSS. |
| 19 | PTG0/KBIP0 | bidirectional | Port G general-purpose I/O bit 0 with pull-up, slew-rate and drive-strength control; alternate function keyboard interrupt KBIP0. |
| 20 | PTG1/KBIP1 | bidirectional | Port G general-purpose I/O bit 1 with pull-up, slew-rate and drive-strength control; alternate function keyboard interrupt KBIP1. |
| 21 | PTG2/KBIP2 | bidirectional | Port G general-purpose I/O bit 2 with pull-up, slew-rate and drive-strength control; alternate function keyboard interrupt KBIP2. |
| 22 | PTA0 | bidirectional | Port A general-purpose I/O bit 0 with pull-up, slew-rate and drive-strength control; no alternate function is listed for this pin. |
| 23 | PTA1 | bidirectional | Port A general-purpose I/O bit 1 with pull-up, slew-rate and drive-strength control; no alternate function is listed for this pin. |
| 24 | PTA2 | bidirectional | Port A general-purpose I/O bit 2 with pull-up, slew-rate and drive-strength control; this pin is listed only in the 48-pin package. |
| 25 | PTA7 | bidirectional | Port A general-purpose I/O bit 7 with pull-up, slew-rate and drive-strength control; this pin is listed only in the 48-pin package. |
| 26 | PTB0/TPM3CH0/AD1P0 | bidirectional | Port B general-purpose I/O bit 0 shared with ADC input AD0 and TPM3CH0; TPM3 is not available on AW-series devices, so only the ADC and GPIO functions apply. |
| 27 | PTB1/TPM3CH1/AD1P1 | bidirectional | Port B general-purpose I/O bit 1 shared with ADC input AD1 and TPM3CH1; TPM3 is not available on AW-series devices, so only the ADC and GPIO functions apply. |
| 28 | PTB2/AD1P2 | bidirectional | Port B general-purpose I/O bit 2 shared with ADC input AD2; when used as an analog input the digital I/O function is disabled. |
| 29 | PTB3/AD1P3 | bidirectional | Port B general-purpose I/O bit 3 shared with ADC input AD3; when used as an analog input the digital I/O function is disabled. |
| 30 | PTD0/AD1P8 | bidirectional | Port D general-purpose I/O bit 0 shared with ADC input AD8; when used as an analog input the digital I/O function is disabled. |
| 31 | PTD1/AD1P9 | bidirectional | Port D general-purpose I/O bit 1 shared with ADC input AD9; when used as an analog input the digital I/O function is disabled. |
| 32 | VDDAD | power_in | Positive supply for the ADC analog section, to be kept at the same voltage as VDD and bypassed with a 0.1 µF ceramic capacitor placed close to the pin. |
| 33 | VSSAD | power_in | Ground for the ADC analog section, to be connected to VSS at the same voltage. |
| 34 | PTD2/AD1P10/KBIP5 | bidirectional | Port D general-purpose I/O bit 2 shared with ADC input AD10 and keyboard interrupt KBIP5; when used as an analog input the digital I/O function is disabled. |
| 35 | PTD3/AD1P11/KBIP6 | bidirectional | Port D general-purpose I/O bit 3 shared with ADC input AD11 and keyboard interrupt KBIP6; when used as an analog input the digital I/O function is disabled. |
| 36 | PTG3/KBIP3 | bidirectional | Port G general-purpose I/O bit 3 with pull-up, slew-rate and drive-strength control; alternate function keyboard interrupt KBIP3. |
| 37 | PTG4/KBIP4 | bidirectional | Port G general-purpose I/O bit 4 with pull-up, slew-rate and drive-strength control; alternate function keyboard interrupt KBIP4 (listed only in the 48-pin package). |
| 38 | VREFH | power_in | ADC high reference voltage input, which must not exceed VDDAD. |
| 39 | VREFL | power_in | ADC low reference voltage input, to be connected to VSSAD at the same voltage. |
| 40 | BKGD/MS | bidirectional | Background debug and mode-select pin: sampled low on the rising edge of reset to enter background mode, otherwise it operates as the single-wire background debug pin with an internal pull-up. |
| 41 | PTG5/XTAL | bidirectional | Port G general-purpose I/O bit 5 that becomes the oscillator XTAL output when the external crystal/resonator is enabled. |
| 42 | PTG6/EXTAL | bidirectional | Port G general-purpose I/O bit 6 that becomes the oscillator EXTAL input (external clock or crystal/resonator) when the external oscillator is enabled. |
| 43 | VSS | power_in | Second ground pin, to be connected to system ground or a low-impedance path to the main VSS pin. |
| 44 | PTC0/SCL1 | bidirectional | Port C general-purpose I/O bit 0 with pull-up, slew-rate and drive-strength control; alternate function IIC clock SCL1. |
| 45 | PTC1/SDA1 | bidirectional | Port C general-purpose I/O bit 1 with pull-up, slew-rate and drive-strength control; alternate function IIC data SDA1. |
| 46 | PTC2/MCLK | bidirectional | Port C general-purpose I/O bit 2 with pull-up, slew-rate and drive-strength control; alternate function MCLK clock output. |
| 47 | PTC3/TxD2 | bidirectional | Port C general-purpose I/O bit 3 with pull-up, slew-rate and drive-strength control; alternate function SCI2 transmit (TxD2). |
| 48 | PTC5/RxD2 | bidirectional | Port C general-purpose I/O bit 5 with pull-up, slew-rate and drive-strength control; alternate function SCI2 receive (RxD2). |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | QFN-48-EP(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 49 |
CAD (KiCad official)
- Symbol:
MC9S08AW48CFDE - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: QFN-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
mc9s08aw48cfde-etched.step/mc9s08aw48cfde-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mc9s08aw48cfde.step/mc9s08aw48cfde.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: NXP Semicon datasheet (296 pp, sha256
a02b13679de67119, retrieved 2026-10-30, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).