3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownMAX861IUA+
Analog Devices Inc Maxim Integrated · DC-DC Converters · MSOP-8
MAX861IUA+ from Analog Devices Inc Maxim Integrated, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FC | input | Frequency Control input. Selects one of three switching frequencies per Table 1: FC=VDD or open ~13kHz, FC=GND ~100kHz, FC=OUT ~250kHz (MAX861). FC input current is only -2 to -4 uA when FC<4V. |
| 2 | C1+ | passive | Flying-Capacitor Positive Terminal. Connect the positive terminal of the flying (pump) capacitor C1 (typically 2.2 uF at 250 kHz) between C1+ and C1-. |
| 3 | GND | power_in | Ground reference in inverter mode. In doubler mode, this pin becomes the Positive Input Supply - the input voltage is applied between pin 3 (positive) and pin 5 (which serves as ground). |
| 4 | C1- | passive | Flying-Capacitor Negative Terminal. Connect the negative terminal of the flying (pump) capacitor C1 between C1+ (pin 2) and C1- (pin 4). |
| 5 | OUT | power_out | Charge-pump output. In inverter mode this is the Negative Output (-VIN nominal). In doubler mode this pin becomes Ground. Sources/sinks up to 50 mA with ~12 ohm typical output resistance. |
| 6 | LV | input | Low-Voltage-Operation input. Connect to GND for inverting operation (may be floated if VDD > 3V for MAX660/ICL7660 compatibility). In doubler mode, must be connected to OUT for all input voltages. |
| 7 | SHDN | input | Active-Low Shutdown input. Drive low (<0.3 V) to shut down the charge pump (supply current drops below 1 uA). Drive high (>1.2 V) to enable. In inverter mode, tie to VDD if unused; in doubler mode, tie to GND if unused. Do not leave floating. |
| 8 | VDD | power_in | Positive Input Supply in inverter mode (+1.5V to +5.5V). In doubler mode this pin becomes the Doubled Positive Output (approximately 2 x VIN). Absolute maximum VDD to GND is +6.0V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc Maxim Integrated |
| Package | MSOP-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Ordering variants
Same part, different packaging or reel option.
MAX861IUA+MAX861IUA+ISAMAX861IUA+ESAMAX861IUA+MSAMAX861IUA+MJAMAX861IUA+C/D
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage, inverter (LV = GND) | VDD | 1.5 | 5.5 | V | Inverter, LV = GND | 2 | |
| Supply Voltage, doubler (LV = OUT) | VDD | 2.5 | 5.5 | V | Doubler, LV = OUT | 2 | |
| Switching Frequency | fS | 8 | 13 | kHz | MAX861, FC = VDD | 3 | |
| Switching Frequency | fS | 60 | 100 | kHz | MAX861, FC = GND | 3 | |
| Switching Frequency | fS | 160 | 250 | kHz | MAX861, FC = OUT | 3 | |
| Output Resistance | ROUT | 20 | 35 | Ω | VDD = 3V, VOUT more negative than -2.5V | 2 | |
| Output Resistance | ROUT | 12 | 25 | Ω | VDD = 5V, VOUT more negative than -3.75V | 2 | |
| Shutdown Supply Current | ISHDN | 1 | 10 | µA | SHDN < 0.3V | 3 | |
| Shutdown Threshold, low | VIL | 0.3 | V | 3 | |||
| Shutdown Threshold, high | VIH | 1.2 | V | 3 | |||
| Voltage-Conversion Efficiency | 99 | 99.9 | % | 3 | |||
| Time to Exit Shutdown | 500 | µs | No load, VOUT = -4V | 3 | |||
| FC Current (from VDD) | IFC | -2 | -4 | µA | 3 | ||
| Supply Voltage VDD to GND or GND to OUT (absolute maximum) | VDD | 6 | V | VDD to GND or GND to OUT | 2 | ||
| Continuous Output Current (OUT, VDD) | IOUT | 60 | mA | Continuous | 2 | ||
| Output Short-Circuit to GND duration | 1 | s | Note 1 | 2 | |||
| Operating Temperature Range, MAX861I/E | TA | -25 | 85 | °C | MAX86_I_A | 2 | |
| Storage Temperature Range | TSTG | -65 | 160 | °C | 2 | ||
| Lead Temperature (soldering, 10s) | 300 | °C | Soldering, 10s | 2 | |||
| Soldering Temperature (reflow) | 240 | °C | Reflow | 2 |
CAD (KiCad official)
- Symbol:
MAX861IUA+ - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
max861iua-etched.step/max861iua-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max861iua.step/max861iua.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices Inc Maxim Integrated datasheet (None pp, sha256
924043bfeecf2e5f, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).