3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSI4060-C2A-GM
SILICON LABS · RF Transceiver ICs · QFN-20-EP(4x4)
SI4060-C2A-GM from SILICON LABS, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SDN | input | Shutdown input (0 to VDD V digital); SDN must be 0 in all modes except Shutdown, and SDN = 1 fully shuts the chip down, losing register contents; it can also be used to reset the chip. |
| 2 | NC | unconnected | Leave pin floating. |
| 3 | NC | unconnected | Leave pin floating. |
| 4 | TX | output | Transmit output is an open-drain PA output, so the L-C match must supply VDD (+3.3 V nominal) to this pin. |
| 5 | NC | unconnected | Not connected internally; the datasheet recommends connecting this pin to GND per the reference design schematic. |
| 6 | VDD | power_in | Supply voltage input to internal regulators, +1.8 to +3.8 V, with +3.3 V recommended. |
| 7 | TXRAMP | output | Programmable bias output with ramp capability for an external FET PA (see section 5.2 of the datasheet). |
| 8 | VDD | power_in | Supply voltage input to internal regulators, +1.8 to +3.8 V, with +3.3 V recommended. |
| 9 | GPIO0 | bidirectional | General purpose digital I/O that can be configured through registers for functions such as microcontroller clock output, FIFO status, POR, wake-up timer, and low battery detect. |
| 10 | GPIO1 | bidirectional | General purpose digital I/O; the extracted pin table gives no separate function text for this pin, so its function is set through the registers like the other GPIO pins. |
| 11 | nIRQ | output | General microcontroller interrupt status output that goes low when any interrupt event occurs; no external pull-up is required, though one may be desirable when multiple interrupt lines are connected. |
| 12 | SCLK | input | Serial clock input (0 to VDD V) for the 4-line serial bus; data is clocked in on positive edge transitions. |
| 13 | SDO | output | Serial data readback output (0 to VDD V) for reading the internal control registers. |
| 14 | SDI | input | Serial data input (0 to VDD V) carrying the data stream for the 4-line serial bus. |
| 15 | nSEL | input | Serial interface select input (0 to VDD V) providing the select/enable function for the 4-line serial bus. |
| 16 | XOUT | output | Crystal oscillator output; connect to an external 25 to 32 MHz crystal, or leave floating when driving the chip from an external source on XIN. |
| 17 | XIN | input | Crystal oscillator input; connect to an external 25 to 32 MHz crystal or to an external reference source. |
| 18 | GND | power_in | Ground; leave floating with a crystal per the reference schematic, or connect to a separate TCXO ground when using a TCXO. |
| 19 | GPIO2 | bidirectional | General purpose digital I/O that can be configured through registers for functions such as microcontroller clock output, FIFO status, POR, wake-up timer, and low battery detect. |
| 20 | GPIO3 | bidirectional | General purpose digital I/O; the extracted pin table gives no separate function text for this pin, so its function is set through the registers like the other GPIO pins. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-20-EP(4x4) |
| Category | RF & Radio |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Range | VDD | 1.8 | 3.3 | 3.8 | V | 4 | |
| Operating Ambient Temperature Range | TA | -40 | 85 | °C | 10 | ||
| Junction Temperature Maximum Value | Tj | 105 | °C | 10 | |||
| Storage Temperature Range | TSTG | -55 | 150 | °C | 10 | ||
| Thermal Impedance Junction to Ambient | JA | 25 | °C/W | Based on RF evaluation board measurements | 10 | ||
| VDD to GND | VDD | -0.3 | 3.8 | V | 10 | ||
| Instantaneous VRF-peak to GND on TX Output Pin | VRF-peak | -0.3 | 8 | V | 10 | ||
| Sustained VRF-peak to GND on TX Output Pin | VRF-peak | -0.3 | 6.5 | V | 10 | ||
| Voltage on Analog Inputs | -0.7 | V | 10 | ||||
| Synthesizer Frequency Range (Si4063/60) 850-1050 MHz band | FSYN | 850 | 1050 | MHz | 5 | ||
| Synthesizer Frequency Range (Si4063/60) 350-525 MHz band | FSYN | 350 | 525 | MHz | 5 | ||
| Synthesizer Frequency Range (Si4063/60) 284-350 MHz band | FSYN | 284 | 350 | MHz | 5 | ||
| Synthesizer Frequency Range (Si4063/60) 142-175 MHz band | FSYN | 142 | 175 | MHz | 5 | ||
| TX Frequency Range 850-1050 MHz band | FTX | 850 | 1050 | MHz | 6 | ||
| TX Frequency Range 350-525 MHz band | FTX | 350 | 525 | MHz | 6 | ||
| TX Frequency Range 284-350 MHz band | FTX | 284 | 350 | MHz | 6 | ||
| TX Frequency Range 142-175 MHz band | FTX | 142 | 175 | MHz | 6 | ||
| (G)FSK Data Rate | DRFSK | 0.1 | 500 | kbps | 6 | ||
| 4(G)FSK Data Rate | DR4FSK | 0.2 | 1000 | kbps | 6 | ||
| OOK Data Rate | DROOK | 0.1 | 120 | kbps | 6 | ||
| Output Power Range (Si4060) | PTX60 | -20 | 12.5 | dBm | Typical range at 3.3 V with Class E match optimized for best PA efficiency | 6 | |
| Output Power Variation (Si4060) | 9.5 | 10 | 10.5 | dBm | At 10 dBm PA power setting, 915 MHz, Class E match, 3.3 V, 25 °C | 7 | |
| Logic Low Input Current | IIN | -1 | 1 | µA | 0<VIN<VDD | 9 | |
| Input Current If Pullup is Activated | IINP | 1 | 4 | µA | VIL = 0 V | 9 | |
| Crystal Oscillator Range (XTAL Range) | XTALRange | 25 | 32 | MHz | Tested using an external clock source (similar to TCXO) | 8 | |
| Maximum allowed XIN swing | 1.8 | V peak-to-peak | 25 | ||||
| POR Reset Time | tPOR | 6 | ms | 8 |
CAD (KiCad official)
- Symbol:
SI4060-C2A-GM - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
si4060-c2a-gm-etched.step/si4060-c2a-gm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si4060-c2a-gm.step/si4060-c2a-gm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SILICON LABS datasheet (37 pp, sha256
6c2f75f5b458d69f, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).