component
AT24C08D-STUM-T
Public Made by Adomby adom
Microchip Tech EEPROM, SOT-23-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownAT24C08D-STUM-T
Microchip Tech · EEPROM · SOT-23-5
AT24C08D-STUM-T from Microchip Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | Serial clock input that clocks data to and from the device; commands and input data are latched on the rising edge of SCL and output data is clocked out on the falling edge, and it must be forced high when the bus is idle or pulled high with an external pull-up resistor. |
| 2 | GND | power_in | Ground reference for the power supply, to be connected to system ground. |
| 3 | SDA | bidirectional | Open-drain bidirectional serial data pin that must be pulled high with an external pull-up resistor not exceeding 10 kΩ and may be wire-ORed with other open-drain or open-collector devices on the bus. |
| 4 | VCC | power_in | Device power supply pin for a source voltage of 1.7V to 3.6V; operation at invalid VCC voltages may produce spurious results. |
| 5 | WP | input | Write-protect input that allows normal writes when connected to GND and inhibits all writes to the full protected array when connected to VCC; it is internally pulled down to GND if left floating, but Microchip recommends driving it to a known state with a pull-up of 10 kΩ or less. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOT-23-5 |
| Category | Memory |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Temperature under bias | -55 | 125 | °C | 9 | |||
| Storage temperature | -65 | 150 | °C | 9 | |||
| Supply voltage | VCC | 4.1 | V | 9 | |||
| Voltage on any pin with respect to ground | -0.6 | 4.1 | V | 9 | |||
| DC output current | 5 | mA | 9 | ||||
| ESD protection | 4 | kV | >4 kV | 9 | |||
| Operating temperature (case), industrial | -40 | 85 | °C | Industrial Temperature Range | 9 | ||
| VCC power supply, low voltage grade | VCC | 1.7 | 3.6 | V | 9 | ||
| Supply voltage | VCC | 1.7 | 3.6 | V | 9 | ||
| Supply current (read) | ICC1 | 0.08 | 0.3 | mA | VCC = 1.8V, Read at 400 kHz | 9 | |
| Supply current (read) | ICC1 | 0.15 | 0.5 | mA | VCC = 3.6V, Read at 1 MHz | 9 | |
| Supply current (write) | ICC2 | 0.2 | 1 | mA | VCC = 3.6V, Write at 1 MHz | 9 | |
| Standby current | ISB | 0.08 | 0.4 | μA | VCC = 1.8V, VIN = VCC or GND | 9 | |
| Standby current | ISB | 0.1 | 0.8 | μA | VCC = 3.6V, VIN = VCC or GND | 9 | |
| Input leakage current | ILI | 0.1 | 3 | μA | VIN = VCC or GND | 10 | |
| Output leakage current | ILO | 0.05 | 3 | μA | VOUT = VCC or GND | 10 | |
| Input low level (max is VCC x 0.3) | VIL | -0.6 | V | Note 2; max printed as VCC x 0.3 | 10 | ||
| Output low level | VOL1 | 0.2 | V | VCC = 1.8V, IOL = 0.15 mA | 10 | ||
| Output low level | VOL2 | 0.4 | V | VCC = 3.0V, IOL = 2.1 mA | 10 | ||
| Clock frequency, SCL (Standard mode) | fSCL | 100 | kHz | VCC = 1.7V to 3.6V | 10 | ||
| Clock frequency, SCL (Fast mode) | fSCL | 400 | kHz | VCC = 1.7V to 3.6V | 10 | ||
| Clock frequency, SCL (Fast mode Plus) | fSCL | 1000 | kHz | VCC = 2.5V to 3.6V | 10 | ||
| Clock pulse width low (Standard mode) | tLOW | 4700 | ns | VCC = 1.7V to 3.6V | 10 | ||
| Clock pulse width low (Fast mode) | tLOW | 1300 | ns | VCC = 1.7V to 3.6V | 10 | ||
| Clock pulse width low (Fast mode Plus) | tLOW | 500 | ns | VCC = 2.5V to 3.6V | 10 | ||
| Clock pulse width high (Standard mode) | tHIGH | 4000 | ns | VCC = 1.7V to 3.6V | 10 | ||
| Clock pulse width high (Fast mode) | tHIGH | 600 | ns | VCC = 1.7V to 3.6V | 10 | ||
| Clock pulse width high (Fast mode Plus) | tHIGH | 400 | ns | VCC = 2.5V to 3.6V | 10 | ||
| Clock low to data out valid (Standard mode) | tAA | 4500 | ns | VCC = 1.7V to 3.6V | 10 | ||
| Clock low to data out valid (Fast mode) | tAA | 900 | ns | VCC = 1.7V to 3.6V | 10 | ||
| Clock low to data out valid (Fast mode Plus) | tAA | 450 | ns | VCC = 2.5V to 3.6V | 10 | ||
| Start hold time (Standard mode) | tHD.STA | 4000 | ns | VCC = 1.7V to 3.6V | 11 | ||
| Start hold time (Fast mode) | tHD.STA | 600 | ns | VCC = 1.7V to 3.6V | 11 | ||
| Start hold time (Fast mode Plus) | tHD.STA | 250 | ns | VCC = 2.5V to 3.6V | 11 | ||
| Start set-up time (Standard mode) | tSU.STA | 4700 | ns | VCC = 1.7V to 3.6V | 11 | ||
| Start set-up time (Fast mode) | tSU.STA | 600 | ns | VCC = 1.7V to 3.6V | 11 | ||
| Start set-up time (Fast mode Plus) | tSU.STA | 250 | ns | VCC = 2.5V to 3.6V | 11 | ||
| Data in set-up time (Standard mode) | tSU.DAT | 200 | ns | VCC = 1.7V to 3.6V | 11 | ||
| Data in set-up time (Fast mode) | tSU.DAT | 100 | ns | VCC = 1.7V to 3.6V | 11 | ||
| Data in set-up time (Fast mode Plus) | tSU.DAT | 100 | ns | VCC = 2.5V to 3.6V | 11 | ||
| Write cycle time | tWR | 5 | ms | 11 | |||
| Time required after VCC is stable before device accepts commands | tPUP | 100 | µs | 12 | |||
| Power-on reset threshold voltage | VPOR | 1.5 | V | 12 | |||
| Minimum time at VCC = 0V between power cycles | tPOFF | 1 | ms | 12 | |||
| Input/output capacitance (SDA) | CI/O | 8 | pF | VI/O = 0V | 13 | ||
| Input capacitance (A2, SCL) | CIN | 6 | pF | VIN = 0V | 13 | ||
| Write endurance | 1e+06 | Write Cycles | TA = 25°C, VCC (min.) < VCC < VCC (max.), Byte or Page Write mode | 13 | |||
| Data retention | 100 | Years | TA = 55°C | 13 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 29 |
CAD (KiCad official)
- Symbol:
AT24C08D-STUM-T - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5 (KiCad packages3D, STEP)
- 3D model files:
at24c08d-stum-t-etched.step/at24c08d-stum-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);at24c08d-stum-t.step/at24c08d-stum-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (45 pp, sha256
9f488f70d95d9e19, retrieved 2026-10-24, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).