component
HT1015AREZ
Public Made by Adomby adom
HTCSEMI DC-DC Converters, ESOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownHT1015AREZ
HTCSEMI · DC-DC Converters · ESOP-8
HT1015AREZ from HTCSEMI, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable input: pulling EN below the 2.2 V typical threshold (0.2 V hysteresis) shuts the HT1015A down, and pulling it above the threshold enables it. |
| 2 | VIN | power_in | Input supply for the internal control circuitry, both BOOT regulators and the high-side switch, specified for 9 V to 100 V with an absolute maximum range of -0.3 V to +120 V. |
| 3 | GND | power_in | Ground, to be placed as close to the output capacitor as possible to avoid the high-current switch paths. |
| 4 | GND | power_in | Ground, to be placed as close to the output capacitor as possible; the exposed pad must be connected to the GND plane for optimal thermal performance. |
| 5 | FB | input | Feedback input to the voltage hysteretic comparator, with the average FB voltage regulated to 800 mV (0.8 V reference) and an absolute maximum range of -0.3 V to +7 V. |
| 6 | NC | unconnected | No connection. |
| 7 | BOOT | passive | Bootstrap positive supply for the internal floating high-side MOSFET driver; a bypass capacitor must be connected between BOOT and SW, with VBOOT rated VSW-0.3 V to VSW+7 V. |
| 8 | SW | output | Switch node output from the high-side switch; a low forward-voltage Schottky rectifier to ground must be placed close to SW, with an absolute maximum range of -0.3 V to +120 V. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HTCSEMI |
| Package | ESOP-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage | VIN | 9 | 100 | V | 4 | ||
| SW, EN, VIN Voltage | VSW，VEN，VIN | -0.3 | 120 | V | 3 | ||
| FB Voltage | VFB | -0.3 | 7 | V | 3 | ||
| Storage Junction Temperature | Tstg | -55 | 150 | ℃ | 3 | ||
| Lead Temperature (Soldering 10 sec.) | Tsolder | 260 | ℃ | Soldering 10 sec. | 3 | ||
| ESD Human Body Model | 2 | kV | Human Body Model | 3 | |||
| Operating ambient temperature | TA | -40 | 85 | ℃ | For all packages | 1 | |
| UVLO | VSTRAT | 8 | V | 4 | |||
| UVLO Hysteresis | VUVLO1 | 0.3 | V | 4 | |||
| Shutdown supply current | ISHUT | 9 | uA | EN=0V | 4 | ||
| Input Quiescent Current | IQ | 500 | uA | VFB=1V | 4 | ||
| Enable threshold voltage | VEN | 2.2 | V | 4 | |||
| Enable threshold voltage Hysteresis | VUVLO2 | 0.2 | V | 4 | |||
| FB Reference Threshold | VFB | 0.8 | V | 4 | |||
| Feedback short voltage | VFB（short） | 0.35 | V | 4 | |||
| Feedback short voltage Hysteresis | VFB2 | 0.42 | V | 4 | |||
| Switching frequency | F | 150 | kHz | IOUT=500mA | 4 | ||
| Maximum Duty Cycle | DMAX | 92 | % | VIN=12V | 4 | ||
| Current Limit Threshold | IPEAK | 1.5 | A | 4 | |||
| On-resistance | RDSON | 400 | mΩ | VIN=18V | 4 | ||
| Thermal shutdown Temp | TSD | 150 | ℃ | 4 | |||
| Thermal shutdown Temp Hysteresis | TSH | 30 | ℃ | 4 |
CAD (KiCad official)
- Symbol:
HT1015AREZ - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
ht1015arez-etched.step/ht1015arez-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ht1015arez.step/ht1015arez.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HTCSEMI datasheet (10 pp, sha256
c19a0d8cc7e3eeff, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).