3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownMCP1725-3002E
Microchip Tech · Power Management Specialized - PMIC · SOIC-8
MCP1725-3002E from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input voltage supply; a 1 µF to 10 µF input capacitor is typically sufficient, recommended if the source is several inches away or a battery. |
| 2 | VIN | power_in | Second input voltage supply pin, connected to the same input source as pin 1. |
| 3 | SHDN | input | Active-low shutdown control input; logic high enables the LDO output, logic low disables it and pulls PWRGD low, with typical shutdown quiescent current of 0.1 µA. |
| 4 | GND | power_in | Ground; connect to a quiet circuit ground, it only conducts the LDO quiescent current (typically 120 µA). |
| 5 | PWRGD | output | Open-drain power good output that indicates the LDO output is within 92% (typical) of nominal regulation, with 2% typical hysteresis and a power-up delay set by CDELAY. |
| 6 | CDELAY | passive | Power good delay set-point; an external capacitor to ground adjusts the PWRGD delay from 200 µs (no capacitance) to 300 ms (0.1 µF). |
| 7 | Sense | input | Output voltage sense input for the fixed-output version that provides feedback to the internal circuitry and improves load regulation by compensating for package and layout voltage drops. |
| 8 | VOUT | power_out | Regulated output voltage; a minimum of 1.0 µF output capacitance is required for stability. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Operating Voltage | VIN | 2.3 | 6 | V | Note 1 | 5 | |
| Input Quiescent Current | Iq | 120 | 220 | µA | IL = 0 mA, VIN = Note 1, VOUT = 0.8V to 5.0V | 5 | |
| Input Quiescent Current for SHDN Mode | ISHDN | 0.1 | 3 | µA | SHDN = GND | 5 | |
| Maximum Output Current | IOUT | 500 | mA | VIN = 2.3V to 6.0V, VR = 0.8V to 5.0V, Note 1 | 5 | ||
| Line Regulation | ΔVOUT/(VOUT x ΔVIN) | -0.16 | 0.05 | 0.16 | %/V | (Note 1) VIN ≤ 6V | 5 |
| Load Regulation | ΔVOUT/VOUT | -1 | 0.5 | 1 | % | IOUT = 1 mA to 500 mA, (Note 4) | 5 |
| Output Short Circuit Current | IOUT_SC | 1.2 | A | RLOAD < 0.1Ω, Peak Current | 5 | ||
| Nominal Output Voltage (3.0V fixed) | VR | 3 | V | MCP1725-3002E | 31 | ||
| Output Voltage Tolerance (fixed) | VOUT | -2.5 | 0.5 | 2.5 | % | Note 2; VR - 2.5% to VR + 2.5%, typ ±0.5% VR | 5 |
| Dropout Voltage | VIN-VOUT | 210 | 350 | mV | IOUT = 500 mA, (Note 5) VIN(MIN) = 2.3V | 6 | |
| PWRGD Input Voltage Operating Range (25°C) | VPWRGD_VIN | 1 | 6 | V | TA = +25°C | 6 | |
| PWRGD Input Voltage Operating Range (full temp) | VPWRGD_VIN | 1.2 | 6 | V | TA = -40°C to +125°C; For VIN < 2.3V, ISINK = 100 µA | 6 | |
| PWRGD Threshold Voltage | VPWRGD_TH | 90 | 92 | 94 | %VOUT | Falling Edge, VOUT >= 2.5V Fixed | 6 |
| PWRGD Threshold Hysteresis | VPWRGD_HYS | 1 | 2 | 3 | %VOUT | 6 | |
| PWRGD Output Voltage Low | VPWRGD_L | 0.2 | 0.4 | V | IPWRGD SINK = 1.2 mA, ADJ = 0V, SENSE = 0V | 6 | |
| PWRGD Time Delay (CDELAY = 0.01 µF) | TPG | 10 | 30 | 55 | ms | Rising Edge, RPULLUP = 10 kΩ, ICDELAY = 140 nA (Typ), CDELAY = 0.01 µF | 6 |
| Logic High Input | VSHDN-HIGH | 45 | %VIN | VIN = 2.3V to 6.0V | 6 | ||
| Logic Low Input | VSHDN-LOW | 15 | %VIN | VIN = 2.3V to 6.0V | 6 | ||
| SHDN Input Leakage Current | SHDNILK | -0.1 | 0.001 | 0.1 | µA | VIN = 6V, SHDN = VIN, SHDN = GND | 6 |
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | Steady State | 7 | |
| Maximum Junction Temperature (transient) | TJ | 150 | °C | Transient | 7 | ||
| Storage Temperature Range | TA | -65 | 150 | °C | 7 | ||
| Absolute Maximum Voltage on Any Pin (lower bound) | -0.3 | V | (GND, 0.3V) to (VIN + 0.3)V; lower bound relative to GND | 5 | |||
| Absolute Maximum Storage Temperature | -65 | 150 | °C | 5 | |||
| Absolute Maximum Junction Temperature | TJ | 150 | °C | 5 | |||
| ESD Protection HBM | 2 | kV | all pins, HBM | 5 | |||
| ESD Protection MM | 200 | V | all pins, MM | 5 | |||
| Thermal Resistance, 8LD SOIC junction-to-ambient | θJA | 163 | °C/W | 4-Layer JC51-7 Standard Board | 7 | ||
| Thermal Resistance, 8LD SOIC junction-to-case | θJC | 38.8 | °C/W | 4-Layer JC51-7 Standard Board | 7 | ||
| PWRGD Leakage | PWRGD_LK | 1 | nA | VPWRGD = VIN = 6.0V | 6 | ||
| Detect Threshold to PWRGD Active Time Delay | TVDET-PWRGD | 200 | µs | VADJ or VSENSE = VPWRGD_TH + 20 mV to VPWRGD_TH - 20 mV | 6 | ||
| Output Delay From SHDN | TOR | 100 | µs | SHDN = GND to VIN, VOUT = GND to 95% VR | 7 | ||
| Output Noise | eN | 2 | µV/√Hz | IOUT = 200 mA, f = 1 kHz, COUT = 10 µF (X7R Ceramic), VOUT = 2.5V | 7 | ||
| Power Supply Ripple Rejection Ratio | PSRR | 60 | dB | f = 100 Hz, COUT = 10 µF, IOUT = 10 mA, VINAC = 30 mV pk-pk, CIN = 0 µF | 7 | ||
| Thermal Shutdown Temperature | TSD | 150 | °C | IOUT = 100 µA, VOUT = 1.8V, VIN = 2.8V | 7 | ||
| Thermal Shutdown Hysteresis | TSD | 10 | °C | IOUT = 100 µA, VOUT = 1.8V, VIN = 2.8V | 7 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 26 |
CAD (KiCad official)
- Symbol:
MCP1725-3002E - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
mcp1725-3002e-etched.step/mcp1725-3002e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp1725-3002e.step/mcp1725-3002e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (34 pp, sha256
1a98a7ba5571d10d, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).