Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LTC2631CTS8-LZ10#TRMPBF

Analog Devices · Digital To Analog Converters (DACs) · TSOT-23-8

LTC2631CTS8-LZ10#TRMPBF from Analog Devices, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CA0 input Chip Address Bit 0 must be tied to VCC, GND or left floating to select the I2C slave address of the part.
2 SCL input Serial clock input shifts data into SDA on rising edges and is high impedance, requiring a pull-up resistor or current source to VCC.
3 SDA bidirectional Serial data pin is high impedance while data is shifted in and is an open-drain N-channel output during acknowledgment, requiring a pull-up resistor or current source to VCC.
4 GND power_in Ground reference pin for the device.
5 VCC power_in Supply voltage input for the LTC2631-L must be 2.7V to 5.5V and should be bypassed to GND with a 0.1µF capacitor.
6 REF bidirectional Reference input or output where in External Reference mode 0V to VCC sets full scale, and in Internal Reference mode the 10ppm/°C 1.25V output is available, bypassable with up to 10µF (0.33µF recommended) and requiring a buffer for DC load current.
7 VOUT output DAC analog voltage output, with rail-to-rail output swing limited by the supply range and a guaranteed load regulation of up to 10mA sourcing or sinking at 5V.
8 CA1 input Chip Address Bit 1 for the LTC2631-Z must be tied to VCC, GND or left floating to select the I2C slave address of the part.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package TSOT-23-8
Category Data Converters
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Positive Supply Voltage For Specified Performance VCC 2.7 5.5 V For Specified Performance 5
Operating Temperature Range (LTC2631C, commercial grade) 0 70 °C LTC2631C 2
Supply Current, internal reference, VCC=3V, external ref ICC 150 200 µA VCC = 3V, VREF = 2.5V, External Reference 5
Supply Current, VCC=3V internal reference ICC 180 240 µA VCC = 3V, Internal Reference 5
Supply Current, VCC=5V external reference ICC 160 210 µA VCC = 5V, VREF = 2.5V, External Reference 5
Supply Current, VCC=5V internal reference ICC 190 260 µA VCC = 5V, Internal Reference 5
Supply Current in Power-Down Mode (C and I grade) ISD 0.6 1.8 µA VCC = 5V, C-Grade, I-Grade 5
Full-Scale Voltage Temperature Coefficient (C-Grade) VFSTC -10 10 ppm/°C VCC = 3V, Internal Ref. (Note 9); C-Grade 5
Reference Output Voltage (LTC2631-L internal reference) VREF 1.24 1.25 1.26 V 6
Reference Temperature Coefficient -10 10 ppm/°C 6
Reference Input Resistance 160 190 220 kΩ 6
Low Level Output Voltage (SDA) VOL 0.4 V Sink Current = 3mA 6
Output Fall Time tOF 250 ns VO = VIH(MIN) to VO = VIL(MAX), CB = 10pF to 400pF (Note 11) 6
Pulse Width of Spikes Suppressed by Input Filter tSP 0 50 ns 6
Input Leakage IIN -1 1 µA 0.1VCC ≤ VIN ≤ 0.9VCC 6
I/O Pin Capacitance CIN 10 pF (Note 7) 6
Capacitive Load for Each Bus Line CB 400 pF 6
External Capacitive Load on Address Pin CAn CCAn 10 pF 6
Differential Nonlinearity (LTC2631-10) DNL -0.5 0.5 LSB VCC = 3V, Internal Ref. (Note 3) 5
Integral Nonlinearity (LTC2631-10) INL -1 0.2 1 LSB VCC = 3V, Internal Ref. (Note 3) 5
Zero-Scale Error (LTC2631-10) ZSE 0.5 5 mV VCC = 3V, Internal Ref., Code = 0 5
Offset Error (LTC2631-10) VOS -5 5 mV VCC = 3V, Internal Ref. (Note 4) 5
VOS Temperature Coefficient VOSTC -10 10 µV/°C VCC = 3V, Internal Ref. (Note 4) 5
Full-Scale Error FSE -0.4 0.08 0.4 %FSR VCC = 3V, Internal Ref. (Note 14) 5
DAC Output Span (internal reference) VOUT 0 2.5 V Internal Reference 6
SCL Clock Frequency fSCL 0 400 kHz 7
Hold Time (Repeated) Start Condition tHD(STA) 0.6 µs 7
Low Period of the SCL Clock Pin tLOW 1.3 µs 7
High Period of the SCL Clock Pin tHIGH 0.6 µs 7
Set-Up Time for a Repeated Start Condition tSU(STA) 0.6 µs 7
Data Hold Time tHD(DAT) 0 0.9 µs 7
Data Set-Up Time tSU(DAT) 100 ns 7
Rise Time of Both SDA and SCL Signals tr 300 ns (Note 11) 7
Fall Time of Both SDA and SCL Signals tf 300 ns (Note 11) 7
Set-Up Time for Stop Condition tSU(STO) 0.6 µs 7
Bus Free Time Between a Stop and Start Condition tBUF 1.3 µs 7
Settling Time (10-bit, ±0.098%) tS 3.8 µs VCC = 3V (Note 8); ±0.098% (±1LSB at 10-Bits) 7
Supply Voltage (VCC) absolute maximum VCC -0.3 6 V All voltages with respect to GND 2
REF_SEL, SCL, SDA voltage absolute maximum -0.3 6 V 2
Storage Temperature Range -65 150 °C 2
Maximum Junction Temperature TJMAX 150 °C (Note 5) 2
Thermal Resistance Junction-to-Ambient (TS8 8-lead TSOT-23) θJA 195 °C/W 2

CAD (KiCad official)

  • Symbol: LTC2631CTS8-LZ10#TRMPBF
  • Footprint: Package_TO_SOT_SMD:TSOT-23-8
  • 3D model: TSOT-23-8 (KiCad packages3D, STEP)
  • 3D model files: ltc2631cts8-lz10-trmpbf-etched.step / ltc2631cts8-lz10-trmpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc2631cts8-lz10-trmpbf.step / ltc2631cts8-lz10-trmpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (28 pp, sha256 4c98446794069d98, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF