component
TPS60111PWP
Public Made by Adomby adom
Texas Instruments DC-DC Converters, HTSSOP-20-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownTPS60111PWP
Texas Instruments · DC-DC Converters · HTSSOP-20-EP
TPS60111PWP from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Analog ground for internal reference and control circuitry; connect to PGND through a short trace. |
| 2 | SYNC | input | Clock synchronization selection; connect to GND for internal clock or to IN for external synchronization. |
| 3 | ENABLE | input | Enable input; device enters shutdown mode (0.05 µA max) when low and output disconnects from input. |
| 4 | FB | input | Feedback input for 5-V regulation via on-chip 1.22-V reference divider; connect close to load for best regulation. |
| 5 | OUT | power_out | Regulated 5-V ±4% output at 150 mA maximum; bypass to GND with output filter capacitor. |
| 6 | C1+ | output | Positive terminal of charge-pump capacitor C1F; actively driven flying capacitor node. |
| 7 | IN | power_in | Supply input in 2.7-V to 5.4-V range; bypass to GND with (CO/2) µF capacitor and connect both INs through short trace. |
| 8 | C1− | output | Negative terminal of charge-pump capacitor C1F; actively driven flying capacitor node. |
| 9 | PGND | power_in | Power ground for charge-pump current flow; connect all PGND pins together. |
| 10 | PGND | power_in | Power ground for charge-pump current flow; connect all PGND pins together. |
| 11 | PGND | power_in | Power ground for charge-pump current flow; connect all PGND pins together. |
| 12 | PGND | power_in | Power ground for charge-pump current flow; connect all PGND pins together. |
| 13 | C2− | output | Negative terminal of charge-pump capacitor C2F; actively driven flying capacitor node. |
| 14 | IN | power_in | Supply input in 2.7-V to 5.4-V range; bypass to GND with (CO/2) µF capacitor and connect both INs through short trace. |
| 15 | C2+ | output | Positive terminal of charge-pump capacitor C2F; actively driven flying capacitor node. |
| 16 | OUT | power_out | Regulated 5-V ±4% output at 150 mA maximum; connect both OUTs through short trace. |
| 17 | SKIP | input | Mode selection input; low for constant-frequency mode (minimized ripple), high for pulse-skip mode (low quiescent current). |
| 18 | COM | input | Mode selection input; low for push-pull mode (minimized ripple), high/IN for single-ended mode (fewer components). |
| 19 | CLK | input | External clock signal input (400-800 kHz range) when SYNC is high; connect to GND for internal 300-kHz clock. |
| 20 | GND | power_in | Analog ground for internal reference and control circuitry; connect to PGND through a short trace. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20-EP |
| Category | Power Supply Chip |
| Pins | 21 |
CAD (KiCad official)
- Symbol:
TPS60111PWP - Footprint:
Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm - 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
tps60111pwp-etched.step/tps60111pwp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps60111pwp.step/tps60111pwp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (26 pp, sha256
f590960ada84532a, retrieved 2026-10-07, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).