3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMIC2800-G1JJYML-TR
Microchip Tech · Power Management Specialized - PMIC · QFN-16(3x3)
MIC2800-G1JJYML-TR from Microchip Tech, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LOWQ | input | LOWQ mode control: logic high (>1V) selects constant-frequency PWM mode, logic low (<0.2V) selects low-noise LOWQ linear mode, and it must not be left floating. |
| 2 | BIAS | passive | Internal bias supply for control and reference circuitry, to be decoupled to signal ground with a 0.1 µF ceramic and not loaded. |
| 3 | SGND | power_in | Signal ground for the biasing and control circuitry; its current loop should be kept as small as possible. |
| 4 | PGND | power_in | Power ground for the high-current PWM mode; its current loop should be kept as small as possible. |
| 5 | SW | output | Switch node connected to the inductor, driven by the internal power MOSFETs; route it away from sensitive nodes because of high-speed switching. |
| 6 | VIN | power_in | DC/DC converter supply input that must be tied externally to pin 7. |
| 7 | VIN | power_in | LDO2 supply input that must be tied externally to pin 6. |
| 8 | LDO2 | power_out | Output of LDO regulator 2, which is 300 mA capable; in LOWQ mode its output load is limited to 10 mA. |
| 9 | FB | input | Feedback input to the DC/DC error amplifier; for fixed output voltages connect it directly to VOUT. |
| 10 | LDO | power_out | Output of the LOWQ-mode linear regulator, connected to the DC/DC output; in LOWQ mode it can deliver 60 mA and limits LDO1 and LDO2 loads to 10 mA. |
| 11 | LDO1 | power_out | Output of LDO regulator 1, whose input power is provided by the DC/DC switching regulator. |
| 12 | POR | output | Open-drain power-on reset output that goes active low on an output undervoltage condition on any of the three regulated outputs. |
| 13 | CSET | passive | Delay set input where a capacitor to GND sets the POR rising delay; it cannot be grounded directly, and leaving it open gives the minimum delay. |
| 14 | CBYP | passive | Reference bypass input where an external 0.1 µF to GND reduces output noise; it may be left open. |
| 15 | EN1 | input | Active-high enable for the DC/DC converter and LDO1; logic high turns them on, logic low turns them off, and it must not be left floating. |
| 16 | EN2 | input | Active-high enable for LDO2 only; logic high turns it on, logic low turns it off, and it must not be left floating. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-16(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (VIN) | VIN | -0.3 | 6 | V | 3 | ||
| Supply Voltage (VIN) operating range | VIN | 2.7 | 5.5 | V | 3 | ||
| Enable Input Voltage (VEN1, EN2) | VEN1, EN2 | -0.3 | V | max +(VIN+0.3V) | 3 | ||
| Enable Input Voltage (VEN1, EN2) operating range | VEN1, EN2 | 0 | V | max +VIN | 3 | ||
| LOWQ, POR voltage | LOWQ, POR | -0.3 | 6 | V | 3 | ||
| LOWQ, POR voltage operating range | LOWQ, POR | 0 | 5.5 | V | 3 | ||
| Junction Temperature (TJ) | TJ | -40 | 125 | °C | 3 | ||
| Storage Temperature (TS) | TS | -65 | 150 | °C | 3 | ||
| Lead Temperature | 260 | °C | soldering, 10 sec. | 3 | |||
| ESD Rating | 2 | kV | Human body model, 1.5 kΩ in series with 100 pF | 3 | |||
| Junction Thermal Resistance QFN-16 | θJA | 45 | °C/W | 16-Ld QFN | 3 | ||
| UVLO Threshold | UVLOTH | 2.45 | 2.55 | 2.65 | V | Rising input voltage during turn on | 4 |
| UVLO Hysteresis | UVLOHYS | 100 | mV | 4 | |||
| Ground Pin Current in Shutdown | IGND_SHDN | 0.2 | 5 | µA | All EN = 0V | 4 | |
| Overtemperature Shutdown | TSD | 160 | °C | 4 | |||
| Overtemperature Shutdown Hysteresis | TSDHYS | 23 | °C | 4 | |||
| Enable Input Voltage Logic Low | VIH | 0.2 | V | 4 | |||
| Enable Input Voltage Logic High | VIL | 1 | V | 4 | |||
| Enable Input Current | IENLK | 0.1 | 1 | µA | VIL ≤ 0.2V | 4 | |
| Turn-on Time (DC/DC) | tTURN-ON | 83 | 350 | µs | EN2 = VIN; ILOAD = 300 mA; CBYP = 0.1 µF | 4 | |
| POR Threshold Voltage, Failing | VTHLOW_POR | 90 | 91 | % | Low Threshold, % of nominal (Flag ON) | 4 | |
| POR Threshold Voltage, Rising | VTHIGH_POR | 96 | 99 | % | High Threshold, % of nominal (Flag OFF) | 4 | |
| POR Output Logic Low Voltage | VOLPOR | 10 | 100 | mV | IL = 250 µA | 4 | |
| Flag Leakage Current | ILEAKPOR | 0.01 | 1 | µA | Flag OFF | 4 | |
| CSET Pin Current Source | ICSET | 0.75 | 1.25 | 1.75 | µA | VCSET = 0V | 4 |
| CSET Pin Threshold Voltage | VTHCSET | 1.25 | V | POR = High | 4 | ||
| Output Voltage Accuracy (DC/DC, LOWQ High) | VOUT | -2 | 2 | % | Fixed Output Voltages | 5 | |
| Output Voltage Accuracy (DC/DC, LOWQ High, bold range) | VOUT | -3 | 3 | % | bold values, -40°C ≤ TJ ≤ +125°C | 5 | |
| Current Limit in PWM Mode | ILIM | 0.75 | 1 | 1.6 | A | VOUT = 0.9*VNOM | 5 |
| Output Voltage Line Regulation | (∆VOUT/VOUT)/∆VIN | 0.2 | %/V | VOUT > 2.4V; VIN = VOUT + 300 mV to 5.5V, ILOAD= 100 mA | 5 | ||
| Output Voltage Load Regulation | ∆VOUT/VOUT | 0.2 | 1.5 | % | 20 mA < ILOAD < 300 mA | 5 | |
| Maximum Duty Cycle | DCMAX | 100 | % | VFB ≤ 0.4V | 5 | ||
| Oscillator Frequency | fosc | 1.8 | 2 | 2.2 | MHz | 5 | |
| Output Voltage Noise (DC/DC) | VN | 60 | µVRMS | COUT = 2.2 µF; CBYP = 0.1 µF; 10 Hz to 100 KHz | 5 | ||
| Output Voltage Accuracy (DC/DC, LOWQ Low) | VOUT | -2 | 2 | % | Variation from nominal VOUT | 5 | |
| Output Voltage Accuracy (DC/DC, LOWQ Low, -40°C to +125°C) | VOUT | -3 | 3 | % | Variation from nominal VOUT; -40°C to +125°C | 5 | |
| Output Voltage Temp. Coefficient | TCVOUT | 40 | ppm/C | 5 | |||
| Line Regulation (DC/DC, LOWQ Low) | (∆VOUT/VOUT)/∆VIN | 0.02 | 0.3 | %/V | VIN = VOUT + 1V to 5.5V; IOUT = 100 µA | 5 | |
| Load Regulation (DC/DC, LOWQ Low) | ∆VOUT/VOUT | 0.2 | 1.5 | % | IOUT = 100 µA to 50 mA | 5 | |
| Ripple Rejection (DC/DC, LOWQ Low) | PSRR | 50 | dB | f = up to 1 kHz; COUT = 2.2 µF; CBYP = 0.1 µF | 5 | ||
| Ripple Rejection (DC/DC, LOWQ Low) | PSRR | 30 | dB | f = 20 kHz; COUT = 2.2 µF; CBYP = 0.1 µF | 5 | ||
| Current Limit (DC/DC, LOWQ Low) | ILIM_LOWQ | 80 | 120 | 190 | mA | VOUT = 0V | 5 |
| Output Current Capability (LDO1, VIN ≥ 1.8V) | IOUT | 300 | mA | VIN ≥ 1.8V | 6 | ||
| Output Current Capability (LDO1, VIN ≥ 1.5V) | IOUT | 120 | mA | VIN ≥ 1.5V | 6 | ||
| Output Voltage Accuracy (LDO1, LOWQ High) | VOUT | -2 | 2 | % | Variation from nominal VOUT | 6 | |
| Output Voltage Accuracy (LDO1, LOWQ High, -40°C to +125°C) | VOUT | -3 | 3 | % | Variation from nominal VOUT; -40°C to +125°C | 6 | |
| Current Limit (LDO1, LOWQ High) | ILIM | 350 | 500 | 700 | mA | VOUT = 0V | 6 |
| Ripple Rejection (LDO1, LOWQ High) | PSRR | 70 | dB | f = up to 1 kHz; COUT = 2.2 µF; CBYP = 0.1 µF | 6 | ||
| Ripple Rejection (LDO1, LOWQ High) | PSRR | 44 | dB | f = 20 kHz; COUT = 2.2 µF; CBYP = 0.1 µF | 6 | ||
| Output Voltage Noise (LDO1) | VN | 30 | µVRMS | COUT = 2.2 µF; CBYP = 0.1 µF; 10 Hz to 100 KHz | 6 | ||
| Output Voltage Accuracy (LDO1, LOWQ Low) | VOUT | -3 | 3 | % | Variation from nominal VOUT | 6 | |
| Output Voltage Accuracy (LDO1, LOWQ Low, -40°C to +125°C) | VOUT | -4 | 4 | % | Variation from nominal VOUT; -40°C to +125°C | 6 | |
| Current Limit (LDO1, LOWQ Low) | ILIM | 50 | 85 | 125 | mA | VOUT = 0V | 6 |
| Ripple Rejection (LDO1, LOWQ Low) | PSRR | 70 | dB | f = up to 1 kHz; COUT = 2.2 µF; CBYP = 0.1 µF | 6 | ||
| Ripple Rejection (LDO1, LOWQ Low) | PSRR | 42 | dB | f = 20 kHz; COUT = 2.2 µF; CBYP = 0.1 µF | 6 | ||
| Output Voltage Accuracy (LDO2, LOWQ High) | VOUT | -2 | 2 | % | Variation from nominal VOUT | 7 | |
| Output Voltage Accuracy (LDO2, LOWQ High, -40°C to +125°C) | VOUT | -3 | 3 | % | Variation from nominal VOUT; -40°C to +125°C | 7 | |
| Line Regulation (LDO2, LOWQ High) | (∆VOUT/VOUT)/∆VIN | 0.02 | 0.3 | %/V | VIN = VOUT +1V to 5.5V; IOUT = 100 µA | 7 | |
| Ripple Rejection (LDO2, LOWQ High) | PSRR | 75 | dB | f = up to 1 kHz; COUT = 2.2 µF; CBYP = 0.1 µF | 7 | ||
| Ripple Rejection (LDO2, LOWQ High) | PSRR | 40 | dB | f = 20 kHz; COUT = 2.2 µF; CBYP = 0.1 µF | 7 | ||
| Current Limit (LDO2, LOWQ High) | ILIM | 400 | 550 | 850 | mA | VOUT = 0V | 7 |
| Output Voltage Noise (LDO2) | VN | 25 | µVRMS | COUT = 2.2 µF; CBYP = 0.1 µF; 10 Hz to 100 KHz | 7 | ||
| Output Voltage Accuracy (LDO2, LOWQ Low) | VOUT | -3 | 3 | % | Variation from nominal VOUT | 7 | |
| Output Voltage Accuracy (LDO2, LOWQ Low, -40°C to +125°C) | VOUT | -4 | 4 | % | Variation from nominal VOUT; -40°C to +125°C | 7 | |
| Current Limit (LDO2, LOWQ Low) | ILIM | 50 | 85 | 125 | mA | VIN = 2.7V; VOUT = 0V | 7 |
CAD (KiCad official)
- Symbol:
MIC2800-G1JJYML-TR - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
mic2800-g1jjyml-tr-etched.step/mic2800-g1jjyml-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic2800-g1jjyml-tr.step/mic2800-g1jjyml-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (30 pp, sha256
59709361ca877f0a, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).