3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLP2951-03YM-TR
Microchip Tech · Linear Voltage Regulators (LDO) · SOIC-8
LP2951-03YM-TR from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VOUT | power_out | Regulated voltage output, guaranteed 100 mA output, and requires a 1.0 μF (or greater) capacitor to ground to prevent oscillation. |
| 2 | SENSE | input | Output voltage sense input; tie to pin 1 (VOUT) for 5V output using the internal divider. |
| 3 | SHDN | input | Logic-compatible shutdown input that switches the regulator on and off. |
| 4 | GND | power_in | Ground terminal. |
| 5 | ERROR | output | Open-collector error output that goes low when the output is more than about 5% out of regulation, requires an external pull-up of 100 kΩ to 1 MΩ, and can sink 400 μA. |
| 6 | 5V TAP | passive | Internal resistor divider tap for 5V output; tie to pin 7 (FB) for 5V output. |
| 7 | FB | input | Voltage feedback input with nominal 1.235 V reference and 20 nA nominal bias current; output is programmable from 1.235 V to 30 V with external resistors. |
| 8 | VIN | power_in | Unregulated supply voltage input; a 0.1 μF capacitor to ground is recommended if there is more than 10 inches of wire to the AC filter capacitor or a battery is used. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output voltage | VOUT | 4.95 | 5 | 5.05 | V | TJ = 25°C, LP2951-03 (±1%) | 5 |
| Output voltage | VOUT | 4.925 | 5.075 | V | -25°C ≤ TJ ≤ +85°C, LP2951-03 (±1%) | 6 | |
| Output voltage over full temperature range | VOUT | 4.9 | 5.1 | V | -40°C to +125°C, LP2951-03 (±1%) | 6 | |
| Output voltage over load variation | VOUT | 4.88 | 5.12 | V | LP2951-03 (±1%), 100 μA ≤ IL ≤ 100 mA, TJ ≤ TJ(max) | 6 | |
| Output voltage temperature coefficient | 50 | 150 | ppm/°C | LP2951-03 (±1%), Note 1 | 6 | ||
| Line regulation | 0.04 | 0.2 | % | LP2951-03 (±1%), Note 2, 3 | 7 | ||
| Line regulation | 0.4 | % | LP2951-03 (±1%), Note 2, 3 | 7 | |||
| Load regulation | 0.1 | 0.2 | % | LP2951-03 (±1%), Note 2, 100 μA ≤ IL ≤ 100 mA | 7 | ||
| Load regulation | 0.3 | % | LP2951-03 (±1%), Note 2, 100 μA ≤ IL ≤ 100 mA | 7 | |||
| Dropout voltage | 50 | 80 | mV | Note 4, IL = 100 μA | 7 | ||
| Dropout voltage | 150 | mV | Note 4, IL = 100 μA | 7 | |||
| Dropout voltage | 380 | 450 | mV | Note 4, IL = 100 mA | 7 | ||
| Dropout voltage | 600 | mV | Note 4, IL = 100 mA | 7 | |||
| Ground current | 100 | 150 | μA | IL = 100 μA | 7 | ||
| Ground current | 200 | μA | IL = 100 μA | 7 | |||
| Ground current | 8 | 12 | mA | IL = 100 mA | 7 | ||
| Ground current | 14 | mA | IL = 100 mA | 7 | |||
| Dropout current | 180 | 250 | μA | VIN = 4.5V, IL = 100 μA | 8 | ||
| Current limit | 160 | 220 | mA | VOUT = 0V | 8 | ||
| Thermal regulation | 0.05 | 0.2 | %/W | Note 5 | 8 | ||
| Reference voltage | VREF | 1.21 | 1.235 | 1.26 | V | LP2951-03 (±1%) | 8 |
| Reference voltage | VREF | 1.2 | 1.27 | V | LP2951-03 (±1%) | 8 | |
| Reference voltage | VREF | 1.185 | 1.285 | V | LP2951-03 (±1%), Note 7 | 8 | |
| Feedback bias current | 20 | 40 | nA | 9 | |||
| Feedback bias current | 60 | nA | 9 | ||||
| Output leakage current | 0.01 | 1 | μA | 9 | |||
| Output leakage current | 2 | μA | VOH = 30V | 9 | |||
| Output low voltage (flag) | 150 | 250 | mV | VIN = 4.5V, IOL = 200μA | 9 | ||
| Output low voltage (flag) | 400 | mV | VIN = 4.5V, IOL = 200μA | 9 | |||
| Upper threshold voltage | 40 | 60 | mV | Note 6 | 9 | ||
| Lower threshold voltage | 75 | 95 | mV | Note 6 | 9 | ||
| Lower threshold voltage | 140 | mV | Note 6 | 9 | |||
| Input logic voltage Low | 0.7 | V | LP2951-03 (±1%) | 10 | |||
| Input logic voltage High | 2 | V | LP2951-03 (±1%) | 10 | |||
| Shutdown input current | 30 | 50 | μA | VSHUTDOWN = 2.4V | 11 | ||
| Shutdown input current | 100 | μA | VSHUTDOWN = 2.4V | 11 | |||
| Shutdown input current | 450 | 600 | μA | VSHUTDOWN = 30V | 11 | ||
| Shutdown input current | 700 | μA | VSHUTDOWN = 30V | 11 | |||
| Regulator output current in shutdown | 3 | 10 | μA | 11 | |||
| Regulator output current in shutdown | 20 | μA | Note 9 | 11 | |||
| Junction operating temperature | TJ | -40 | 125 | °C | 12 | ||
| Storage temperature range | TA | -65 | 125 | °C | 12 | ||
| Storage temperature | -65 | 150 | °C | 5 | |||
| Input supply voltage | -0.3 | 30 | V | 5 | |||
| Feedback input voltage | -1.5 | 30 | V | Note 2, 3 | 5 | ||
| Shutdown input voltage | -0.3 | 30 | V | Note 2 | 5 | ||
| Error comparator output voltage | -0.3 | 30 | V | Note 2 | 5 | ||
| Thermal resistance junction-to-ambient, SOIC package | JA | 160 | °C/W | Typically mounting on a 1'' square copper-clad FR4 circuit board | 12 | ||
| Thermal resistance junction-to-case, SOIC package | JC | 25 | °C/W | 12 |
CAD (KiCad official)
- Symbol:
LP2951-03YM-TR - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
lp2951-03ym-tr-etched.step/lp2951-03ym-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp2951-03ym-tr.step/lp2951-03ym-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (30 pp, sha256
9310d226e59ae920, retrieved 2026-10-27, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).