Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

FT24C1024A-TTR-T

FMD(Fremont Micro Devices) · EEPROM · TSSOP-8

FT24C1024A-TTR-T from FMD(Fremont Micro Devices), in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No-connect pin with no internal function stated in the datasheet.
2 A1 input Device address input that is matched against the 5th/6th device address bits and is internally recognized as VIL if left unconnected.
3 A2 input Device address input that is matched against the 5th/6th device address bits and is internally recognized as VIL if left unconnected.
4 GND power_in Ground reference for the device.
5 SDA bidirectional Serial data line, bi-directional with an open-drain output that can be wire-ORed and is normally pulled high by an external resistor.
6 SCL input Serial clock input where the rising edge latches data into the device and the falling edge clocks data out.
7 WP input Write protect input that disables all programming when tied to VIH or VCC and allows programming when left unconnected or at VIL; reads are unaffected.
8 VCC power_in Supply voltage pin with a 1.7V to 5.5V range, requiring a decoupling capacitor of at least 10nF.

Key specifications

Parameter Value
Manufacturer FMD(Fremont Micro Devices)
Package TSSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC1 1.7 5.5 V 10
Supply read current ICC1 0.5 1 mA VCC @ 5.5V SCL = 400 kHz 10
Supply write current ICC2 2 8 mA VCC @ 5.5V SCL = 400 kHz 10
Standby supply current ISB1 1 µA VCC @ 1.7V, VIN = VCC or VSS 10
Input leakage current IIL 3 µA VIN = VCC or VSS 10
Output leakage current ILO 3 µA VIN = VCC or VSS 10
Input low level VIL -0.6 V max is VCC × 0.3 10
Output low level VOL1 0.2 V VCC @ 1.7V, IOL = 0.15 mA 10
Output low level VOL2 0.4 V VCC @ 3.0V, IOL = 2.1 mA 10
Clock frequency, SCL fSCL 400 kHz 1.7V 9
Clock frequency, SCL fSCL 1000 kHz 2.5-5.5 V 9
Clock pulse width low tLOW 1.3 µs 1.7V and 2.5-5.5 V 9
Clock pulse width high tHIGH 0.6 µs 1.7V and 2.5-5.5 V 9
Noise suppression time tI 100 ns 1.7V 9
Noise suppression time tI 50 ns 2.5-5.5 V 9
Clock low to data out valid tAA 0.1 0.9 µs 1.7V and 2.5-5.5 V 9
Bus free time before new transmission tBUF 1.3 µs 1.7V and 2.5-5.5 V 9
START hold time tHD.STA 0.6 µs 1.7V and 2.5-5.5 V 9
START set-up time tSU.STA 0.6 µs 1.7V and 2.5-5.5 V 9
Data in hold time tHD.DAT 0 µs 1.7V and 2.5-5.5 V 9
Data in set-up time tSU.DAT 100 ns 1.7V and 2.5-5.5 V 9
Input rise time tR 0.3 µs 1.7V and 2.5-5.5 V 9
Input fall time tF 300 ns 1.7V and 2.5-5.5 V 9
STOP set-up time tSU.STO 0.6 µs 1.7V and 2.5-5.5 V 9
Data out hold time tDH 50 ns 1.7V and 2.5-5.5 V 9
Vcc slew rate at power up tPWR,R 0.1 50 V/ms 1.7V and 2.5-5.5 V 9
Time required after VCC stable before commands tPUP 100 µs 1.7V and 2.5-5.5 V 9
Minimum time at Vcc=0V between power cycles tPOFF 500 ms 1.7V and 2.5-5.5 V 9
Write cycle time tWR 5 ms 1.7V and 2.5-5.5 V 9
Endurance 1e+06 Write Cycles 25°C, Page Mode, 3.3V 9
Operating temperature -40 85 °C Industrial 2
Storage temperature -50 125 °C 2
Input voltage on any pin relative to ground -0.3 V max is VCC + 0.3V 2
Maximum voltage 8 V 2
ESD protection on all pins 4000 V >4000V 2

CAD (KiCad official)

  • Symbol: FT24C1024A-TTR-T
  • Footprint: Package_SO:TSSOP-8_3x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: ft24c1024a-ttr-t-etched.step / ft24c1024a-ttr-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ft24c1024a-ttr-t.step / ft24c1024a-ttr-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: FMD(Fremont Micro Devices) datasheet (16 pp, sha256 effedb83593f8d68, retrieved 2026-10-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF