3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownM24128-BFMN6TP
STMicroelectronics · EEPROM · SOIC-8
M24128-BFMN6TP from STMicroelectronics, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | E0 | input | Chip enable input that sets device select code bit b1; it must be tied to VCC or VSS and is read as low when left floating. |
| 2 | E1 | input | Chip enable input that sets device select code bit b2; it must be tied to VCC or VSS and is read as low when left floating. |
| 3 | E2 | input | Chip enable input that sets device select code bit b3; it must be tied to VCC or VSS and is read as low when left floating. |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage. |
| 5 | SDA | bidirectional | Serial data I/O, an open-drain output that requires a pull-up resistor to VCC. |
| 6 | SCL | input | Serial clock input used to strobe data on SDA in and to output data on SDA. |
| 7 | WC | input | Write control; when driven high, write operations to the entire memory array are disabled, and when driven low or left floating they are enabled. |
| 8 | VCC | power_in | Supply voltage; the M24128-BF operates from 1.7 V to 5.5 V over -40 °C to +85 °C. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SOIC-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 1.7 | 5.5 | V | Table 8, voltage range F | 19 | |
| Ambient operating temperature READ | TA | -40 | 85 | °C | READ | 19 | |
| Ambient operating temperature WRITE | TA | 0 | 85 | °C | WRITE | 19 | |
| Operating clock frequency | fC | 400 | kHz | VCC ≥ 1.6 V | 19 | ||
| Operating clock frequency | fC | 1000 | kHz | VCC ≥ 1.7 V | 19 | ||
| Ambient operating temperature | TA | -40 | 130 | °C | 18 | ||
| Storage temperature | TSTG | -65 | 150 | °C | 18 | ||
| DC output current | IOL | 5 | mA | SDA = 0 | 18 | ||
| Input or output range | VIO | -0.5 | 6.5 | V | 18 | ||
| Supply voltage | VCC | -0.5 | 6.5 | V | 18 | ||
| Electrostatic pulse (Human Body model) | VESD | 4000 | V | Human Body model, AEC-Q100-002 | 18 | ||
| Input capacitance (SDA) | CIN | 8 | pF | Characterized only | 20 | ||
| Input capacitance (other pins) | CIN | 6 | pF | Characterized only | 20 | ||
| Input impedance (E2, E1, E0, WC) low | ZL | 50 | kΩ | VIN < 0.3 VCC | 20 | ||
| Input impedance (E2, E1, E0, WC) high | ZH | 500 | kΩ | VIN > 0.7 VCC | 20 | ||
| Write cycle endurance | Ncycle | 4e+06 | cycles | TA ≤ 25 °C, VCC(min) < VCC < VCC(max) | 20 | ||
| Write cycle endurance | Ncycle | 1.2e+06 | cycles | TA = 85 °C, VCC(min) < VCC < VCC(max) | 20 | ||
| Data retention | 200 | Year | TA = 55 °C | 20 | |||
| Input leakage current (SCL, SDA, E2, E1, E0) | ILI | -2 | 2 | µA | VIN = VSS or VCC, device in Standby mode | 23 | |
| Output leakage current | ILO | -2 | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 23 | |
| Supply current (Read) | ICC | 0.8 | mA | VCC = 1.6 V or 0.7 V, fc = 400 kHz | 23 | ||
| Supply current (Read) | ICC | 2.5 | mA | VCC = 1.6 V or 0.7 V, fc = 1 MHz | 23 | ||
| Supply current (Write) | ICC0 | 2 | mA | Value overaged over tW, VCC < 2.5 V | 23 | ||
| Standby supply current | ICC1 | 1 | µA | Device not selected, VIN = VSS or VCC, VCC = 1.6 V or 0.7 V | 23 | ||
| Input low voltage (SCL, SDA, WC, E2, E1, E0) | VIL | -0.45 | 0.25 | V | VCC < 2.5 V; max printed as 0.25 VCC | 23 | |
| Input high voltage (SCL, SDA) | VIH | 0.7 | 6.5 | V | VCC < 2.5 V; min printed as 0.7 VCC | 23 | |
| Input high voltage (WC, E2, E1, E0) | VIH | 0.7 | 0.6 | V | VCC < 2.5 V; min printed as 0.7 VCC, max printed as VCC+0.6 V | 23 | |
| Output low voltage | VOL | 0.2 | V | IOL = 1 mA, VCC = 1.6 V or 1.7 V | 23 | ||
| Clock frequency | fC | 400 | kHz | 24 | |||
| Clock pulse width high | tCHCL | 600 | ns | 24 | |||
| Clock pulse width low | tCLCH | 1300 | ns | 24 | |||
| SDA (out) fall time | tQL1QL2 | 20 | 300 | ns | CL = 10 pF | 24 | |
| Data in setup time | tDXCH | 100 | ns | 24 | |||
| Data in hold time | tCLDX | 0 | ns | 24 | |||
| Data out hold time | tCLQX | 50 | ns | 24 | |||
| Clock low to next data valid (access time) | tCLQV | 900 | ns | 24 | |||
| Start condition setup time | tCHDL | 600 | ns | 24 | |||
| Start condition hold time | tDLCL | 600 | ns | 24 | |||
| Stop condition set up time | tCHDH | 600 | ns | 24 | |||
| Time between Stop condition and next Start condition | tDHDL | 1300 | ns | 24 | |||
| WC set up time (before the Start condition) | tWLDL | 0 | µs | WC=0 set up time to enable WRITE | 24 | ||
| WC hold time (after the Stop condition) | tDHWH | 1 | µs | WC=0 hold time to enable WRITE | 24 | ||
| Internal Write cycle duration | tW | 5 | ms | 24 | |||
| Pulse width ignored (input filter on SCL and SDA) | tNS | 50 | ns | single glitch | 24 | ||
| Clock frequency | fC | 0 | 1 | MHz | 25 | ||
| Clock pulse width high | tCHCL | 260 | ns | 25 | |||
| Clock pulse width low | tCLCH | 500 | ns | 25 | |||
| SDA (out) fall time | tQL1QL2 | 20 | 120 | ns | CL = 10 pF | 25 | |
| Data in setup time | tDXCH | 50 | ns | 25 | |||
| Data in hold time | tCLDX | 0 | ns | 25 | |||
| Data out hold time | tCLQX | 50 | ns | 25 | |||
| Clock low to next data valid (access time) | tCLQV | 450 | ns | 25 | |||
| Start condition setup time | tCHDL | 250 | ns | 25 | |||
| Start condition hold time | tDLCL | 250 | ns | 25 | |||
| Stop condition setup time | tCHDH | 250 | ns | 25 | |||
| Time between Stop condition and next Start condition | tDHDL | 500 | ns | 25 | |||
| WC set up time (before the Start condition) | tWLDL | 0 | µs | WC=0 set up time to enable WRITE | 25 | ||
| WC hold time (after the Stop condition) | tDHWH | 1 | µs | WC=0 hold time to enable WRITE | 25 | ||
| Write time | tW | 5 | ms | 25 | |||
| Pulse width ignored (input filter on SCL and SDA) | tNS | 50 | ns | 25 |
CAD (KiCad official)
- Symbol:
M24128-BFMN6TP - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
m24128-bfmn6tp-etched.step/m24128-bfmn6tp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m24128-bfmn6tp.step/m24128-bfmn6tp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (46 pp, sha256
f271d50817e50b0b, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).