Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LM76003RNPR

Texas Instruments · DC-DC Converters · WQFN-30-EP(4x6)

LM76003RNPR from Texas Instruments, in a WQFN-30-EP(4x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 SW power_out Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor.
2 SW power_out Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor.
3 SW power_out Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor.
4 SW power_out Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor.
5 SW power_out Switching output of the regulator, internally connected to the HS FET source and LS FET drain; connect to the power inductor and bootstrap capacitor.
6 BOOT passive Bootstrap capacitor connection for the high-side driver; connect a high-quality 470-nF capacitor from this pin to SW.
7 NC unconnected Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability.
8 VCC power_out Output of the internal bias supply used for internal control circuits; connect a high-quality 2.2-µF capacitor to GND, and TI does not recommend loading this pin with external circuitry.
9 BIAS power_in Optional BIAS LDO supply input; tie to VOUT for 3.3 V ≤ VOUT ≤ 18 V or to an external 3.3-V or 5-V rail to improve efficiency, with a 1-µF capacitor to ground when used, and tie to ground when not in use.
10 RT input Switching frequency setting pin; a resistor from this pin to ground sets the frequency, the default is 500 kHz if floating, and it must not be shorted to ground.
11 SS/TRK input Soft-start control pin; leave floating for the 6.3-ms internal ramp, add a capacitor to ground to extend soft start, or drive an external ramp for tracking, and do not short to ground.
12 FB input Feedback input for output voltage regulation, connected to a resistor divider; it must never be shorted to ground during operation.
13 AGND power_in Analog ground and reference for internal references and logic; all electrical parameters are measured with respect to this pin and it connects to system ground.
14 AGND power_in Analog ground and reference for internal references and logic; all electrical parameters are measured with respect to this pin and it connects to system ground.
15 AGND power_in Analog ground and reference for internal references and logic; all electrical parameters are measured with respect to this pin and it connects to system ground.
16 PGOOD output Open-drain power-good flag output that is high when VOUT regulation is OK and low on a fault or when EN is low; connect to a supply through a current-limiting resistor.
17 SYNC/MODE input Synchronization and mode-setting input that must not float: tie to ground for DCM/PFM at light load, to logic high for forced PWM, or to an external clock to synchronize (triggered on the rising edge).
18 EN input Precision-enable input where high turns the regulator on and low turns it off; it must not float, can be tied to VIN, and allows adjustable UVLO via an external divider.
19 NC unconnected Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability.
20 PVIN power_in Supply input to the internal bias LDO and HS FET; connect to the input supply and input bypass capacitor CIN placed right next to this pin and PGND with short traces.
21 PVIN power_in Supply input to the internal bias LDO and HS FET; connect to the input supply and input bypass capacitor CIN placed right next to this pin and PGND with short traces.
22 PVIN power_in Supply input to the internal bias LDO and HS FET; connect to the input supply and input bypass capacitor CIN placed right next to this pin and PGND with short traces.
23 NC unconnected Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability.
24 PGND power_in Power ground connected internally to the LS FET source; connect to system ground, DAP/EP, AGND and the ground side of CIN and COUT with the CIN path kept as short as possible.
25 PGND power_in Power ground connected internally to the LS FET source; connect to system ground, DAP/EP, AGND and the ground side of CIN and COUT with the CIN path kept as short as possible.
26 PGND power_in Power ground connected internally to the LS FET source; connect to system ground, DAP/EP, AGND and the ground side of CIN and COUT with the CIN path kept as short as possible.
27 NC unconnected Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability.
28 NC unconnected Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability.
29 NC unconnected Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability.
30 NC unconnected Not internally connected; connect to ground copper on the PCB to improve heat-sinking and board-level reliability.
31 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package WQFN-30-EP(4x6)
Category Power Management (PMIC)
Pins 31

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Absolute maximum voltage PVIN to PGND -0.3 65 V 5
Absolute maximum voltage EN to AGND -0.3 V max printed as VIN + 0.3 5
Absolute maximum voltage FB, RT, SS/TRK to AGND -0.3 5 V 5
Absolute maximum voltage PGOOD to AGND -0.1 20 V 5
Absolute maximum voltage SYNC to AGND -0.3 5.5 V 5
Absolute maximum voltage BIAS to AGND -0.3 V max printed as lower of (VIN + 0.3) or 30 5
Absolute maximum voltage AGND to PGND -0.3 0.3 V 5
Absolute maximum voltage SW to PGND -0.3 V max printed as VIN + 0.3 5
Absolute maximum voltage SW to PGND less than 10-ns transients -3.5 65 V less than 10-ns transients 5
Absolute maximum voltage BOOT to SW -0.3 5.5 V 5
Absolute maximum voltage VCC to AGND -0.3 5.5 V 5
Junction temperature TJ -40 150 °C 5
Storage temperature Tstg -65 150 °C 5
Operating free-air temperature range TA -40 125 °C over operating free-air temperature range 5
Operating input voltage PVIN to PGND 3.5 60 V 5
EN input voltage 0 V max printed as VIN 5
FB input voltage 0 4.5 V 5
PGOOD input voltage 0 18 V 5
BIAS input voltage, BIAS input not used 0 0.3 V BIAS input not used 5
BIAS input voltage, BIAS input used 0 V BIAS input used; max printed as lower of (VIN + 0.3) or 24 5
AGND to PGND voltage -0.1 0.1 V 5
Output voltage VOUT 1 V max printed as 95% of VIN 5
Output current LM76003 IOUT 0 3.5 A LM76003 5
Operating junction temperature range TJ -40 125 °C recommended operating junction temperature range; limits apply over this range 6
Operating input voltage range VIN 3.5 60 V 6
Shutdown quiescent current ISD 1.2 10 µA VEN = 0 V, TJ = 25℃ 6
Operating quiescent current from VIN (non-switching) IQ_NONSW 0.9 12 µA VEN = 2 V, VFB = 1.5 V, VBIAS = 3.3 V external 6
Enable input high level for VOUT VEN_VOUT_H 1.14 1.204 1.25 V VEN rising 6
Enable input leakage current ILKG_EN 1.4 200 nA VEN = 2 V 6
Internal VCC undervoltage lockout VCC_UVLO 2.96 3.14 3.27 V VCC rising 6
Operating quiescent current from external VBIAS (non-switching) IBIAS_NONSW 21 50 µA VEN = 2 V, VFB = 1.5 V, VBIAS = 3.3 V external 6
Feedback voltage VFB 0.987 1.006 1.017 V PWM mode 6
Input leakage current at FB pin ILKG_FB 0.2 60 nA VFB = 1 V 6
BOOT - SW undervoltage lockout VBOOT_UVLO 1.6 2.2 2.7 V 7
Short-circuit high-side current limit LM76003 IHS_LIMIT 4.35 5.5 6.8 A LM76003 7
Low-side current limit LM76003 ILS_LIMIT 3.4 4.2 5.3 A LM76003 7
Hiccup threshold on FB pin VHICCUP 0.38 0.42 0.46 V 7
Soft-start charge current ISSC 1.8 2 2.2 µA 7
Power-good overvoltage threshold VPGOOD_OV 106 110 113 % % of FB voltage 7
Power-good undervoltage threshold VPGOOD_UV 86 90 93 % % of FB voltage 7
High-side MOSFET on-resistance RDS_ON_HS 95 150 mΩ IOUT = 1 A, VBIAS = VOUT = 3.3 V 7
Low-side MOSFET on-resistance RDS_ON_LS 45 85 mΩ IOUT = 1 A, VBIAS = VOUT = 3.3 V 7
Thermal shutdown threshold TSD 160 °C Shutdown threshold 7
Thermal shutdown recovery threshold TSD 135 °C Recovery threshold 7
Sync input high level threshold VSYNC_HIGH 2 V 8
Sync input low level threshold VSYNC_LOW 0.4 V 8
Sync input minimum on- and off-time tSYNC_MIN 80 ns 8
PGOOD rising edge deglitch delay tPGOOD_RISE 80 140 200 µs 8
PGOOD falling edge deglitch delay tPGOOD_FALL 80 140 200 µs 8
Maximum switch on-time tON-MAX 3.8 8 11.4 µs HS timeout in dropout 8
Internal oscillator frequency fOSC 440 500 560 kHz RT = Open 8
Minimum adjustable frequency by RT or SYNC fADJ 270 300 330 kHz RT = 133 kΩ, 0.1% 8
Maximum adjustable frequency by RT or SYNC fADJ 1980 2200 2420 kHz RT = 17.4 kΩ, 0.1% 8
Junction-to-ambient thermal resistance RθJA 29.6 °C/W 6
Junction-to-case (top) thermal resistance RθJC(top) 17.6 °C/W 6
Junction-to-board thermal resistance RθJB 9.1 °C/W 6
Junction-to-case (bottom) thermal resistance RθJC(bot) 1 °C/W 6

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper 3. Minimize trace length to the FB pin net. Place both feedback resistors, RFBT and RFBB, close to the FB pin. Because the FB node is high impedance, maintain the copper area as small as possible. Rou 42

CAD (Adom-generated)

  • Symbol: LM76003RNPR
  • Footprint: Adom_Gen:Texas_Instruments_LM76003_03fead
  • 3D model: generated to fit the land (STEP)
  • 3D model files: lm76003rnpr-etched.step / lm76003rnpr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lm76003rnpr.step / lm76003rnpr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (59 pp, sha256 1ef4ab645f7e3202, retrieved 2026-11-21)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.

Datasheet PDF